topic Re: Difficulty in selecting sketch entities in Creo in 3D Part & Assembly Design

Difficulty in selecting sketch entities in Creo

M.Liszka — Thu, 10 Oct 2024 13:10:18 GMT

I'm working in Creo Parametric version 11.0.1.0.

When in sketch mode and selecting entities for adding dimensions, I hover over the entity until it highlights, but when I click the entity often does not get selected. I thought there might be a config parameter that affects the sensitivity of sketch entity selection, but I wasn't able to identify one.

Re: Difficulty in selecting sketch entities in Creo

Tdaugherty — Thu, 10 Oct 2024 13:24:38 GMT

Can you check your computer's scaling setting? I've seen this issue occur when your scaling factor is set to something other than 100%. You can access the scaling settings by right clicking on your desktop and choosing Display Settings. Set it to 100% and try again.

Re: Difficulty in selecting sketch entities in Creo

kdirth — Thu, 10 Oct 2024 14:22:26 GMT

Could be a graphics issue. In 7.0 and Creo+ (running Creo12.0) I get instant highlighting and selection.

Is it the same with the display set to wireframe?

You could also try setting config graphics to win32_gdi to disable the video card. If this helps, you may need to use an updated driver (the latest is not always the best).

Re: Difficulty in selecting sketch entities in Creo

StephenW — Thu, 10 Oct 2024 14:58:40 GMT

There is an option in the config.pro called :

pick_aperture_radius

If this is set in any of your configs, it may make select more difficult. But honestly, I suspect it is either of the other response, graphics card or scaling.

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Thu, 10 Oct 2024 18:19:56 GMT

Thanks for your reply. This setting was already at 100% for my monitors.

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Thu, 10 Oct 2024 18:59:57 GMT

Thanks for your reply. This option was not already set, and setting it to its default of 7 did not seem to make things any better or worse.

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Thu, 10 Oct 2024 19:01:02 GMT

Setting the display to wireframe did not change this behavior.

How do you set config graphics to win32_gdi?

Re: Difficulty in selecting sketch entities in Creo

kdirth — Thu, 10 Oct 2024 19:13:33 GMT

In your default work directory, there should be a file named config.pro. Open it in a text editor and add the line graphics win32_gdi

Re: Difficulty in selecting sketch entities in Creo

Catalina — Tue, 15 Oct 2024 08:27:58 GMT

Hi @M.Liszka,

I wanted to see if you got the help you needed.

If so, please mark the appropriate reply as the Accepted Solution. It will help other members who may have the same question.
Please note that industry experts also review the replies and may eventually accept one of them as solution on your behalf.

Of course, if you have more to share on your issue, please pursue the conversation.

Thanks,

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Tue, 15 Oct 2024 16:43:33 GMT

I tried adding this parameter as you suggested. It definitely had a noticeable affect on the graphics, but not on the original problem.

Re: Difficulty in selecting sketch entities in Creo

tbraxton — Tue, 15 Oct 2024 16:46:41 GMT

What is the selection filter set to when you are having difficulty in sketch mode? It should be set to "all sketcher" but it is possible that it may not be.

Re: Difficulty in selecting sketch entities in Creo

StephenW — Tue, 15 Oct 2024 16:59:20 GMT

If that option had solved your problem, it would have meant your issue is specifically a graphics card issue.

Since it didn't, your problem is elsewhere.

Make sure you remove the option, it will destroy your overall system performance.

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Tue, 15 Oct 2024 17:25:08 GMT

Yes, I noticed! The option has been removed.

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Tue, 15 Oct 2024 17:29:42 GMT

This problem typically happens when trying to apply dimensions or reference dimensions, at which point the selection filter is set to "All."

Re: Difficulty in selecting sketch entities in Creo

StephenW — Tue, 15 Oct 2024 17:37:50 GMT

Is this in a large assembly? I know that once my assemblies get to a good size, selection begins to get worse. Most prominently in large assembly drawings, but in modeling also. Even worse when surface models are involved.

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Tue, 15 Oct 2024 17:48:57 GMT

No, this happens in sketch mode when modelling parts - even simple parts. I've seen what you're referring to as well, but that usually appears as a lag in highlighting or selecting entities. What I'm experiencing is no lag in highlighting but failure to select. I should also emphasize that this is an intermittent and so far unpredictable problem.

Re: Difficulty in selecting sketch entities in Creo

StephenW — Tue, 15 Oct 2024 17:44:28 GMT

Yes, agreed. Lag is correct for large assy's.

Intermittent and unpredictable is horrible. Hard to figure out what the issue is.

Re: Difficulty in selecting sketch entities in Creo

hdasilva — Thu, 09 Jan 2025 08:34:02 GMT

I am experiencing the same problem with Creo 11.0.2.0, I am also using Creo 9.0 without this issue.

Re: Difficulty in selecting sketch entities in Creo

RaphMORIN — Tue, 14 Jan 2025 11:33:04 GMT

I have the same problem. It appeared instantly after switching to Creo 11. We were previously using Creo 4 without issue. I think there's a problem with Creo 11. We submitted the case to support and they told us it was a driver or hardware issue as we're not using certified hardware !

It's really annoying, I thing we now have to click approximately 30% more to do the same job. And that's a lot of time wasted.

Here's another with the exact same problem : https://community.ptc.com/t5/3D-Part-Assembly-Design/Creo-11-Selection-Issues/m-p/982605#M137268

Re: Difficulty in selecting sketch entities in Creo

M.Liszka — Tue, 14 Jan 2025 16:06:24 GMT

Well, at least I'm not alone! Thanks for pointing to the other thread where users are having this same problem.

What non-certified hardware are you using? I'm pretty sure the graphics card I'm using is certified as I'm using an NVIDIA card on an HP laptop.