cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Showing results for 
Search instead for 
Did you mean: 

Community Tip - Did you get called away in the middle of writing a post? Don't worry you can find your unfinished post later in the Drafts section of your profile page. X

How to designate parameters automatically using Model check ?

hsuryaprakash
1-Newbie

How to designate parameters automatically using Model check ?

How to designate parameters automatically using Model check ?

1 ACCEPTED SOLUTION

Accepted Solutions

According to image value in ModelCHECK parameter is missing, add PDM as value for parameters. e.g. PRT_PARAMETER TRIANGLE NONE EQ PDM

View solution in original post

10 REPLIES 10

You may try using <MODE>_PARAMETER <PARAM> <TYPE> <FUNCTION> PDM (e.g. PRT_PARAMETER DESCRIPTION NONE EQ PDM) in start file

Hi

I have tried the above method but unable to achieve the desire thing.

Kindly find the attached image

DESIGNATE.JPG

According to image value in ModelCHECK parameter is missing, add PDM as value for parameters. e.g. PRT_PARAMETER TRIANGLE NONE EQ PDM

Haris,

Does the syntax help you to designate parameter?

Yes.Now I can able to designate

Thanks a lot...

Could you please mark the appropriate reply as correct answer?

Hello, I'm strugeling with modelcheck (Creo3.0M110)

I added  lines in the file to check like below:

PRT_PARAMETER NAME_1 NONE EQ PDM
PRT_PARAMETER NAME_2 NONE EQ PDM
PRT_PARAMETER DRAWING_REVISION STR EQ LIST_PRT_REV
PRT_PARAMETER PRODUCT_MODEL STR EQ LIST_PRODUCT_MODEL
PRT_PARAMETER ENGINEER STR
PRT_PARAMETER CHECKER STR
PRT_PARAMETER APPROVER STR
PRT_PARAMETER ORDERNUMBER STR
PRT_PARAMETER SERIALNUMBER STR
PRT_PARAMETER PUMPMODEL STR
PRT_PARAMETER DOCUMENT_TYPE STR
PRT_PARAMETER DOCUMENT_CLASS STR
PRT_PARAMETER DIN24250_NUMBER INTEGER
PRT_PARAMETER INFO STR
PRT_PARAMETER SPEC_NUMBER STR
PRT_PARAMETER RELEASE STR
PRT_PARAMETER POSITION_NUMBER STR
PRT_PARAMETER MASS REAL
PRT_PARAMETER VOLUME REAL
PRT_PARAMETER DENSITY REAL
PRT_PARAMETER ID_NUMBER STR
PRT_PARAMETER NOTES STR
PRT_PARAMETER NATIVE_DESCR STR
PRT_PARAMETER NUMBER_OF_STAGES INTEGER
PRT_PARAMETER DRAWING_UNITS STR
PRT_PARAMETER PRODUCT_SIZE STR
PRT_PARAMETER FLS_UNIT_SYSTEM STR
PRT_PARAMETER FLS_LANGUAGE STR
PRT_PARAMETER FLS_DESIGN_FILE STR
PRT_PARAMETER FLS_MIGRATION_SOURCE STR
PRT_PARAMETER FLS_REGULATORY_REQUIREMENTS STR
PRT_PARAMETER FLS_ALTERNATE_NUMBER STR
PRT_PARAMETER COMMODITY_CODE STR
PRT_PARAMETER FLS_DESCRIPTION NONE EQ PDM
PRT_PARAMETER OEM_SITE STR
PRT_PARAMETER DESIGN_CENTER STR
PRT_PARAMETER EXTENDED_DESCRIPTION STR
PRT_PARAMETER FLS_ALTERNATE_DESCRIPTION STR
PRT_PARAMETER ORIGINAL_EQUIP_MFG STR

 

All parameters are added except the ones with "NONE EQ PDM"

PTC ModelCHECK

PARAMCHECK  
   Error updating parameter(s): 3  
 
    FLS_DESCRIPTION  
    NAME_1  
    NAME_2  

Tried "NONE EQ PDM", it worked well. May be some for information will clarify. 

Hi,

@Mahesh_Sharma I have added parameter i.e. LBH which should carry the value of OVERALL SIZE of model check refereeing Article CS29792. But parameter is not appearing in Part/Assy parameters. Kindly help me out.

Thanks in Advance.

 
 

 

@GS_9583712 

 

It seems added correctly in start file. however it will be worth checking:

 

1. ADD_CHK_PARAM is set to Y in check file

2. After executing ModelCHECK, is it using correct set of config files? You can check that in ModelCHECK report. 

 

Top Tags