by
ZC_8293506
![]() ![]()
11 Replies
983
Views
| Hi, I have an problem about the table. The user defined parameter can
not displayed after i add some...
|
11 Replies
|
983
Views
| ||
by
NickKaehler
![]() ![]()
4 Replies
1313
Views
| Greetings, I was recently asked to change a drawing of a drill bit. So I
modified the model that I h...
|
4 Replies
|
1313
Views
| ||
by
ptc-1999062
![]() ![]()
5 Replies
523
Views
| Hello, I am trying to model a calibration target (similar to these
larger and higher dot density). I...
|
5 Replies
|
523
Views
| ||
by
StevenDumon
![]()
0 Replies
124
Views
| We are using the Automatic Rep since upgrading to Creo 5, particularly
when PTC by default hides the...
|
0 Replies
|
124
Views
| ||
by
Spedex
![]() ![]()
2 Replies
259
Views
| Hey, have a look at the following picture: As you can see, the beginning
of the measurement-line is ...
|
2 Replies
|
259
Views
| ||
by
jaehyunahn
![]() ![]()
4 Replies
398
Views
| Hi, Is there a good, need material library so i wasted lots of time for
this...but cannot find a def...
|
4 Replies
|
398
Views
| ||
5 Replies
471
Views
| Dear Community, After creating exploded states in the sub-assemblies, I
would like these states to b...
|
5 Replies
|
471
Views
| ||
by
Pettersson
![]() ![]()
5 Replies
364
Views
| Let's say I have a rather complex, curved geometry. I need to highlight
an area of this geometry in ...
|
5 Replies
|
364
Views
| ||
by
MilongueroViejo
![]() ![]()
5 Replies
672
Views
| I'm teaching myself Creo with version 6.0 student edition. In trying to
work on the framework utilit...
|
5 Replies
|
672
Views
| ||
by
SCHEnovice
![]() ![]()
1 Reply
934
Views
| Hopefully this is the right place to ask these questions, however, I am
having difficulty with two a...
|
1 Reply
|
934
Views
| ||
by
Carlos.Castillo
![]() ![]()
1 Reply
436
Views
| Hello, everyone: I am trying to model a coloured ribbon cable 24AWG (8
conductors), and my question ...
|
1 Reply
|
436
Views
| ||
by
dnordin
![]()
0 Replies
139
Views
| I opened a ticket with PTC asking a few questions about Creo View ECAD,
and I thought I'd ask them h...
|
0 Replies
|
139
Views
| ||
4 Replies
358
Views
| I need to join two plates at a right angle to each other using a bevel
weld reinforced by a fillet w...
|
4 Replies
|
358
Views
| ||
4 Replies
1493
Views
| Can we able to defined the length of cable in creo schematic?
|
4 Replies
|
1493
Views
| ||
by
Spedex
![]() ![]()
18 Replies
1015
Views
| Hey guys, i am using PTC Creo Parametric 7.0 (Student Edition) I created
a thread on a pin. Unfortun...
|
18 Replies
|
1015
Views
| ||
1 Reply
234
Views
| I am exporting a flat sheetmetal view 1:1 to dxf to send to
manufacturing. Our manufacturing program...
|
1 Reply
|
234
Views
| ||
by
dplachinski
![]() ![]()
6 Replies
479
Views
| I can add the link without issue. When I try to access the url (excel)
sheet, I get two warning mess...
|
6 Replies
|
479
Views
| ||
When saving a cabling assembly to Creo View, the network is saved with
it, leading to a lot of green...
|
0 Replies
|
121
Views
| |||
6 Replies
544
Views
| Hi everyone, Would appreciate if anyone can shed some light on this. I'm
new to Creo 5.0. Trying to ...
|
6 Replies
|
544
Views
| ||
2 Replies
336
Views
| I have a complex assmebly and i am have added a manikin and want to lock
out the selection of all th...
|
2 Replies
|
336
Views
| ||
by
Scott_Zaske
![]() ![]()
2 Replies
395
Views
| My company has recently updated to CREO Schematics 4 and the
functionality of changing cable decorat...
|
2 Replies
|
395
Views
| ||
4 Replies
491
Views
| One of the designers did a sheetmetal design with 4 distinct pieces so
it is in a part file, not an ...
|
4 Replies
|
491
Views
| ||
4 Replies
542
Views
| How to use creo schematics to get a length of Wires & Cables!! I am
looking for solutions that a par...
|
4 Replies
|
542
Views
| ||
by
AnandKumar
![]() ![]()
8 Replies
1984
Views
| @Hello All, Please find below the attached file "frame.prt". This creo
part has an parameter named p...
|
8 Replies
|
1984
Views
| ||
by
jalexander
![]() ![]()
1 Reply
260
Views
| When a view is converted to draft group, the line entities do not
maintain the colors they had befor...
|
1 Reply
|
260
Views
| ||
2 Replies
287
Views
| My company is currently giving some thought to how we handle standards.
There are two main aspects, ...
|
2 Replies
|
287
Views
| ||
by
Siege_engineer
![]() ![]()
2 Replies
368
Views
| Hello all, I am using Excel for pattern definiton, this can be achived
with the config option "part_...
|
2 Replies
|
368
Views
| ||
by
FK_7297405
![]() ![]()
3 Replies
322
Views
| I am trying to generate a hole geometry feature that is rotated
angularly around a specified central...
|
3 Replies
|
322
Views
| ||
by
dplachinski
![]() ![]()
5 Replies
549
Views
| Can you show annotations / Gtol's in an External inheritance or External
merge model? Original model...
|
5 Replies
|
549
Views
| ||
by
RA_7571150
![]()
0 Replies
200
Views
| I have been using a threaded shaft with RH and LH threads. The design is
provided with 2 nuts, each ...
|
0 Replies
|
200
Views
|
Subject | Author |
---|---|