| |
All Not sure if this is 'intended functionality' but attached is a
drawing view of a model created u...
|
4 Replies
|
2144
Views
| |
|
by
HugoHermans
on
Dec 13, 2020
05:21 AM
Latest post on
Sep 26, 2014
10:26 AM
by
TomU
1 Reply
1023
Views
|
Suppose a sketch contains 4 datum points. I know how to rename the
sketch, but I want to rename the ...
|
1 Reply
|
1023
Views
| |
| |
Hello everyone, I have a need to create center lines between the slots
made between the patterned fe...
|
9 Replies
|
3438
Views
| |
| |
Dear All, I would like to use the branch functionality in a line to
joint 2 segment of a same line. ...
|
1 Reply
|
1959
Views
| |
| |
I want to animate an assembly and save as an mpeg. This is pretty basic,
yet I dont know how to do i...
|
1 Reply
|
1204
Views
| |
| |
Hello, I have received a task of simulating a difficult scenario. Rubber
(Elastollan 1185A) is over ...
|
6 Replies
|
3303
Views
| |
| |
Hi team, could you please help how to write mac's for cable drawing
tables. thanks, madhu This threa...
|
1 Reply
|
966
Views
| |
| |
Could any one help me about following questions: 1. How the part
parameters are linked with pcf file...
|
10 Replies
|
4628
Views
| |
| |
Hi, I am trying to pass an ECAD .IDF file from Mentor Graphics
Expedition into CREO Direct Modeling ...
|
4 Replies
|
5718
Views
| |
| |
hv fun ^^) Video Link : 2405 This thread is inactive and closed by the
PTC Community Management Team...
|
1 Reply
|
6703
Views
| |
| |
Hello all, I have been working with Creo 3 for a few days now & keep
running into the same problem w...
|
4 Replies
|
2010
Views
| |
|
by
lteckani
on
May 03, 2018
05:20 AM
Latest post on
Sep 25, 2014
12:19 AM
by
lteckani
2 Replies
1844
Views
|
How do I best replicate the load on a seesaw on one side at the middle?
I performed load analysis of...
|
2 Replies
|
1844
Views
| |
| |
Obviously if you want the drawing you would back up the drawing. Same
with export I would pick the d...
|
3 Replies
|
882
Views
| |
| |
Obviously if you want the drawing you would back up the drawing. Same
with export I would pick the d...
|
0 Replies
|
442
Views
| |
|
by
davehaigh
on
Dec 12, 2020
09:29 PM
Latest post on
Sep 24, 2014
04:07 PM
by
TomU
2 Replies
982
Views
|
Wait just a second, I think your making this more complicated than it
needs to be. Create a startup ...
|
2 Replies
|
982
Views
| |
|
by
TomU
on
Dec 12, 2020
09:29 PM
Latest post on
Sep 24, 2014
04:07 PM
by
TomU
1 Reply
609
Views
|
In case you missed it, the original question was how to get Creo data
out of Windchill without using...
|
1 Reply
|
609
Views
| |
| |
This can be done but not with Read only access. This level of access
only allows the user to see tha...
|
1 Reply
|
632
Views
| |
|
by
EricHuffman
on
Dec 12, 2020
09:30 PM
Latest post on
Sep 24, 2014
02:18 PM
by
TomU
1 Reply
827
Views
|
Gurus, Is it possible to copy CREO files from Windchill to local drive?
We want to allow a user to l...
|
1 Reply
|
827
Views
| |
|
by
TomU
on
Dec 12, 2020
09:29 PM
0 Replies
455
Views
|
Nope. As of 9.1 M050 PTC has discontinued the ability to directly
download Creo CAD files from Windc...
|
0 Replies
|
455
Views
| |
| |
This can be done but not with Read only access. This level of access
only allows the user to see tha...
|
0 Replies
|
539
Views
| |
| |
Recently our needs for PCB design software increased, and our current
solution is straining to meet ...
|
4 Replies
|
2942
Views
| |
| |
Recently our needs for PCB design software increased, and our current
solution is straining to meet ...
|
0 Replies
|
531
Views
| |
| |
There is a known problem with republishing in Creo View upon check-in
when a lower level rep or fami...
|
4 Replies
|
2360
Views
| |
| |
In our drawing templates, the person that set them up put layer rules in
place along with states. If...
|
1 Reply
|
1118
Views
| |
|
by
AR
on
Dec 12, 2020
09:30 PM
Latest post on
Sep 24, 2014
08:06 AM
by
AR
2 Replies
1030
Views
|
with Creo v.20 I can export the 3D model and 2D drawing and then open it
and use it in Creo Modeling...
|
2 Replies
|
1030
Views
| |
|
by
spete
on
Dec 12, 2020
10:27 AM
Latest post on
Sep 24, 2014
05:01 AM
by
ReinhardN
8 Replies
5659
Views
|
I am working on an assembly that was copied from another assembly. Some
of the reused components are...
|
8 Replies
|
5659
Views
| |
| |
Why is creo useless in wireframe mode when rotating the model or
assembly. Only when I turn off show...
|
4 Replies
|
1928
Views
| |
| |
I am working on a school project, and I need to design this building in
a 3-D building model. I have...
|
6 Replies
|
3804
Views
| |
| |
We design machines and many of the parts are purchased, we do not know
the exact dimensions but want...
|
8 Replies
|
2901
Views
| |
|
by
MGortner
on
Dec 12, 2020
10:05 PM
Latest post on
Sep 24, 2014
12:43 AM
by
mms-2
3 Replies
3348
Views
|
In CREO 1 and 2, Is there a way to see a different color on open quilt
edges while in shaded or shad...
|
3 Replies
|
3348
Views
| |
