Community Tip - If community subscription notifications are filling up your inbox you can set up a daily digest and get all your notifications in a single email. X
by
craig.s.bates
![]() ![]()
6 Replies
1397
Views
| Does anyone know how to create custom hatch patterns besides line
styles, angles and spacing? For ex...
|
6 Replies
|
1397
Views
| ||
by
SteveLucas
![]() ![]()
1 Reply
609
Views
| I am having a problem with profile milling. when I cut a diameter with a
profile sequence I get a se...
|
1 Reply
|
609
Views
| ||
PTC's suggested technique is to add an "_1" "_2" etc after each new
routing. Add the same to the cab...
|
0 Replies
|
241
Views
| |||
What do I need to do to open a Unigraphics part file? TIA John This
thread is inactive and closed by...
|
0 Replies
|
1212
Views
| |||
by
ptc-3191571
![]() ![]()
2 Replies
395
Views
| I am having an assembly file & I am inserting an component into it
,there are almost 10 instances of...
|
2 Replies
|
395
Views
| ||
1 Reply
314
Views
| Hello, just a bit more information regarding what I was asking. I have
attached a wordart scrawl dep...
|
1 Reply
|
314
Views
| ||
2 Replies
3367
Views
| You can download the complete newsletter authored by Todd Kraft, by
clicking here. PTC Product Focus...
|
2 Replies
|
3367
Views
| ||
by
TerryMcFall
![]() ![]()
1 Reply
557
Views
| Somebody must have run across this situation before... We're migrating
IL 3.4 to PDML and need to cr...
|
1 Reply
|
557
Views
| ||
On 07/26/10 13:06, Terry McFall wrote: > Somebody must have run across
this situation before… > > We...
|
0 Replies
|
215
Views
| |||
10 Replies
6276
Views
| Hi, I'm just getting to grips with WF4 student/personal ed. To learn pro
e I have started a project ...
|
10 Replies
|
6276
Views
| ||
by
TerryMcFall
![]() ![]()
1 Reply
272
Views
| Somebody must have run across this situation before... We're migrating
IL 3.4 to PDML and need to cr...
|
1 Reply
|
272
Views
| ||
1 Reply
386
Views
| Does anyone have a way to vary the angle dimension shown below so that
the section revolves around t...
|
1 Reply
|
386
Views
| ||
by
SteveBarnhart
![]() ![]()
3 Replies
1121
Views
| Hi all, I've been importing a number of .stp assemblies into Wildfire 4
lately and I'm wondering why...
|
3 Replies
|
1121
Views
| ||
2 Replies
510
Views
| Hi all, Can anybody tell me how a note can be enclosed in a single box?
Tried using "@[text]" in the...
|
2 Replies
|
510
Views
| ||
Hello All, I am usually pretty good at locating 3D files like this, but
I cannot seem to find a file...
|
0 Replies
|
377
Views
| |||
Turns out I was making this more difficult than it needed to be. When
you look in the trail file, pi...
|
0 Replies
|
238
Views
| |||
by
al204
![]() ![]()
2 Replies
448
Views
| Hello Proe Users...I know there are many experienced engineers and
designers using proe out there.I´...
|
2 Replies
|
448
Views
| ||
4 Replies
849
Views
| Not a datum plane, but one surface of an extrude? This thread is
inactive and closed by the PTC Comm...
|
4 Replies
|
849
Views
| ||
Thanks for all the help. There is divided opinion over this, so I have
posted all the responses (and...
|
0 Replies
|
230
Views
| |||
by
InteractiveMesh
![]() ![]()
5 Replies
3740
Views
| Hallo, beim Start des Downloads in Firefox wird ein neuer Tab geöffnet
und der Inhalt als Text ausge...
|
5 Replies
|
3740
Views
| ||
by
linda
![]() ![]()
4 Replies
2193
Views
| the dimension digits and tolerance digits must be the same for
wildfire2.0? 2.05+0.02/0.00 it is pos...
|
4 Replies
|
2193
Views
| ||
3 Replies
2569
Views
| How do I rename a single surface? I know how to rename a feature, that's
not what I am looking for. ...
|
3 Replies
|
2569
Views
| ||
File - Properties - Names (change)
|
0 Replies
|
290
Views
| |||
Pros, Does anyone have a 40"x48" shipping pallet they would like to
share? WF2, step, igs. Thanks, J...
|
0 Replies
|
301
Views
| |||
Hello All. I am trying to check If I using mechanica right. For that, I
tested a standerd paddle par...
|
0 Replies
|
302
Views
| |||
Hi all, Is it possible to show dual dimensions in a repeat region? I
already have some drawing optio...
|
0 Replies
|
370
Views
| |||
I have been having issues with "dirty" iges files. I have started using
"step" where possible as tha...
|
0 Replies
|
330
Views
| |||
by
ptc-886955
![]()
0 Replies
208
Views
| Hello, I was wondering if someone has move Windchill to another server.
I have a production server t...
|
0 Replies
|
208
Views
| ||
by
jwilkerson
![]() ![]()
2 Replies
979
Views
| Hi all, I have been searching the help files and the only place it talks
about 3D section views is i...
|
2 Replies
|
979
Views
| ||
2 Replies
1788
Views
| Hi We people of Europa use all ISO-specifications. When I want to draw a
Gass-thread the program doe...
|
2 Replies
|
1788
Views
|
User | Count |
---|---|
6 | |
5 | |
4 | |
3 | |
2 |
Subject | Author |
---|---|