|
by
cncwhiz
on
Dec 13, 2020
06:55 AM
Latest post on
Sep 22, 2010
09:47 AM
by
cncwhiz
5 Replies
979
Views
|
I have a part that I modeled and I need to make a mirror of the part. I
can mirror it but don't know...
|
5 Replies
|
979
Views
| |
| |
Hi All, When I mesh my model, I get a notice that "Some connection
between surfaces have been ignore...
|
0 Replies
|
730
Views
| |
| |
Hi All, I have a Mechanica model that has a rigid link that I cannot
delete. In order to simplify th...
|
0 Replies
|
591
Views
| |
|
by
proedude
on
Dec 13, 2020
12:56 AM
Latest post on
Sep 22, 2010
01:49 AM
by
bfrandsen
1 Reply
820
Views
|
All - We are currently running PDMLink v9.1 M020 and Pro/ENGINEER
Wildfire 4.0 M130. Our machines ar...
|
1 Reply
|
820
Views
| |
| |
I'm suddenly having problems in moving set datum tags in drawing views.
I've created them in the mod...
|
1 Reply
|
887
Views
| |
| |
Thanks to everyone who responded; I have not had an opportunity to run
down all the suggestions but ...
|
3 Replies
|
881
Views
| |
| |
Anybody know where to find the "ref dim" command in part or assembly
mode on WF 5 ? Bob This thread ...
|
0 Replies
|
345
Views
| |
|
by
BobSchwerdlin
on
Dec 12, 2020
11:03 PM
Latest post on
Sep 21, 2010
02:02 PM
by
kkja
7 Replies
1290
Views
|
Hi all, I've been on Pro/E WF 5.0 (build M040) for about 2 weeks now and
just can't get past the cra...
|
7 Replies
|
1290
Views
| |
| |
Good afternoon PTC users. We have been viewing this forum and providing
individualized feedback to m...
|
0 Replies
|
516
Views
| |
|
by
lococnc
on
Dec 12, 2020
11:03 PM
0 Replies
369
Views
|
Is there any way to export a pro/e model with a parametric midsuface,
without a license of mechanica...
|
0 Replies
|
369
Views
| |
|
by
A.DelNegro
on
Dec 13, 2020
06:55 AM
Latest post on
Sep 21, 2010
08:47 AM
by
bkurth
2 Replies
983
Views
|
I was able to show the axis datum, finally as shown here. The question
is, I have a drawing with the...
|
2 Replies
|
983
Views
| |
|
by
dbms435
on
Dec 13, 2020
06:55 AM
0 Replies
461
Views
|
Users: I can create the first wall in a sheetmetal part but subsequent
walls appear to be impossible...
|
0 Replies
|
461
Views
| |
| |
Hey I just downloaded and installed Pro E Wildfire 5.0 Education Edition
and am struggling to get th...
|
1 Reply
|
2132
Views
| |
| |
Thanks to the respondents, and kudos to Terry Partridge for the
solution. Apparently if you put the ...
|
0 Replies
|
381
Views
| |
| |
Can anyone tell me why Pro makes life so difficult? I have a part in my
assembly, and like all other...
|
1 Reply
|
755
Views
| |
| |
Good Afternoon everyone! I have a few drawings that take quite a while
(20 - 40 minutes) to open if ...
|
0 Replies
|
543
Views
| |
| |
Hi all, I am a new user to Pro/engineer wildfire 5.0. I want to create a
section view in my drawing....
|
2 Replies
|
1835
Views
| |
| |
Chris wins the prize. Thanx. I had shown one of the other axis on my
drawing but apparently you need...
|
0 Replies
|
444
Views
| |
| |
Gurus, I'm trying to add a dimension in another dimension using the
following syntax 3x &d280 = @D T...
|
1 Reply
|
574
Views
| |
| |
CoCreate Modeling 17.0: Up to 2 times faster than version 16.0! See the
comparison at: http://www.yo...
|
0 Replies
|
2786
Views
| |
| |
CoCreate Modeling 17.0: Faster, Easier Modeling with New PULL Command.
See more at: http://www.ptc.c...
|
0 Replies
|
2552
Views
| |
| |
Hi All, I have an assembly that consists of a shaft and a flat blade.The
shaft has a hole that a pin...
|
4 Replies
|
1041
Views
| |
|
by
cfly
on
Dec 12, 2020
03:57 PM
Latest post on
Sep 19, 2010
05:51 PM
by
gkbeer
1 Reply
1293
Views
|
All: Does anyone know why 'Layer Properties' is sometimes grayed out on
a component whose Workspace ...
|
1 Reply
|
1293
Views
| |
| |
Since this list was so helpful for me in previous cases I figure I'd ask
for another stumper, at lea...
|
1 Reply
|
734
Views
| |
|
by
ArunMathew
on
Dec 12, 2020
03:57 PM
Latest post on
Sep 18, 2010
10:31 AM
by
Kevin
1 Reply
2553
Views
|
hi everybody... i have recieved some proe assembly files from our
customer which is arranged hapazar...
|
1 Reply
|
2553
Views
| |
|
by
TracyWillis
on
Dec 12, 2020
11:03 PM
Latest post on
Sep 17, 2010
05:03 PM
by
pgress
2 Replies
705
Views
|
Anyone know whythe File / Edit menu is on thethe Right-hand side, under
the windows Close button in ...
|
2 Replies
|
705
Views
| |
| |
Gurus, I'm having trouble getting my custom balloon to work. It is just
like the "With Qty" option b...
|
0 Replies
|
565
Views
| |
| |
I've been using SDRC then NX for a long time and now my company wants to
switch to Pro-E. I've been ...
|
9 Replies
|
21267
Views
| |
|
by
breiter
on
Dec 12, 2020
03:57 PM
Latest post on
Sep 17, 2010
11:51 AM
by
ptcuser11
1 Reply
912
Views
|
All, I have an assembly i am running an analysis on. It consists of an
inner race, outer race and a ...
|
1 Reply
|
912
Views
| |
| |
Guys, Thanks for the responses. Looks like we'll need to go to a newer
build. We have been testing M...
|
0 Replies
|
447
Views
| |
