| |
I am trying to get a curvature like the photo attached, however it ended
up as a sharp edge, attache...
|
7 Replies
|
1422
Views
| |
| |
Hello everyone, I have mapkey for certain task for one part. How to
convert this mapkey into multipl...
|
7 Replies
|
1344
Views
| |
| |
Simulate features (loads, rigids, constraints, mesh settings, etc.) from
a part level analysis also ...
|
2 Replies
|
828
Views
| |
|
by
ashaik
on
10-24-2019
03:51 AM
Latest post on
10-24-2019
12:58 PM
by
kdirth
1 Reply
331
Views
|
kindy help me i need to change bend radius of sheetmetal part globally
that contains many bends
|
1 Reply
|
331
Views
| |
|
by
Henry_H
on
10-08-2019
05:02 PM
Latest post on
10-24-2019
11:54 AM
by
Henry_H
4 Replies
693
Views
|
In trying to create a datum curve through a points table with 88 points,
it fails if I select the po...
|
4 Replies
|
693
Views
| |
| |
I'm getting into a fairly complex assembly using a combination of
Pro/Program and Relations. This is...
|
14 Replies
|
2429
Views
| |
| |
Hi. Haven't posted on here in nearly ten years. Nothing personal but we
switched back to Autodesk pr...
|
11 Replies
|
3180
Views
| |
| |
Once our drawings are done, our harness mfg facility exports it to
Autocad and adds the following mf...
|
0 Replies
|
339
Views
| |
|
by
wfalco
on
10-22-2019
01:16 PM
Latest post on
10-23-2019
08:29 AM
by
wfalco
5 Replies
623
Views
|
Hi all, Could have searched this. But in somewhat of a hurry to get this
done. I am looking to blank...
|
5 Replies
|
623
Views
| |
| |
hi, my student creo said The file C:1Program Files\PTC1Creo
3.01M1101Common Files\textkrosshatch\iso...
|
3 Replies
|
471
Views
| |
| |
Hi I have an assembly which I opened in Creo 4.0. I come to know that it
has so many issues like mis...
|
3 Replies
|
676
Views
| |
| |
Does anyone know how to add the diameter symbol to the position
tolerance by default? OR.... There i...
|
1 Reply
|
356
Views
| |
|
by
MaikTheBike
on
10-20-2019
12:58 PM
Latest post on
10-21-2019
08:21 PM
by
BHOoi
6 Replies
753
Views
|
Hi, I'd like to create a clamp that holds an toothed belt in place. Here
you can see an example: I c...
|
6 Replies
|
753
Views
| |
|
by
eschinzel
on
10-17-2019
12:01 PM
Latest post on
10-21-2019
01:58 PM
by
kdirth
11 Replies
3166
Views
|
I have a part that when I add it or apply Edit Definition in Default
position it is out from where i...
|
11 Replies
|
3166
Views
| |
| |
To all, I am using CREO 3.0 M090. When I route a cable or wire using a
network everything is fine. W...
|
0 Replies
|
366
Views
| |
|
by
aoler
on
05-04-2018
10:12 AM
Latest post on
10-21-2019
09:57 AM
by
aoler
2 Replies
1498
Views
|
I am attempting to build up a new Connector Shape in Creo Schematics
that will support adding Backsh...
|
2 Replies
|
1498
Views
| |
| |
One of our users is getting newly created limit dimensions on his
drawing displayed as 12.250 - 12.2...
|
3 Replies
|
1193
Views
| |
| |
I have trouble figuring out how to create this pattern, it radiates
outwards to a certain diameter w...
|
5 Replies
|
594
Views
| |
| |
We've recently migrated from Creo 3 to Creo 4 M060. We have a mix of
users with different hardware, ...
|
11 Replies
|
6263
Views
| |
| |
With this article, https://www.ptc.com/en/support/article?n=CS294562,
PTC says that Creo 7 will use ...
|
3 Replies
|
3290
Views
| |
|
by
pwelch
on
05-02-2018
08:26 PM
Latest post on
10-18-2019
09:12 AM
by
at-2
9 Replies
6031
Views
|
How can I create STEP files from CREO Direct Modeling Express? "Help"
mentions that it writes STEP f...
|
9 Replies
|
6031
Views
| |
|
by
amitshah
on
05-04-2018
01:08 PM
Latest post on
10-18-2019
08:43 AM
by
TomU
8 Replies
1780
Views
|
Hi, How can I add, given dimension tolerance in the family table for
respective dimensions. Regards ...
|
8 Replies
|
1780
Views
| |
| |
This has been a recurring issue for me. I am trying to colour the entire
solid body (Not just outer ...
|
8 Replies
|
1151
Views
| |
| |
I'm generating a dxf from Creo Drawing using the Config.pro &
DXF_Export.pro setting. But, when I la...
|
7 Replies
|
1269
Views
| |
| |
How can I use the "plus" button?I searched for a specific config.pro's
option, but I've not find any...
|
2 Replies
|
482
Views
| |
| |
Hi all, after my Creo Parametric was updated to 4.0 I can´t drag and
drop a part from an assemble to...
|
3 Replies
|
829
Views
| |
| |
Hello, Can somebody advise me how to add tolerance limits to several
dimensions in either drawing or...
|
12 Replies
|
3551
Views
| |
| |
Man, I'd like to print this after some tweaks, but it's fighting me...
and when trying it as 2 diffe...
|
4 Replies
|
726
Views
| |
|
by
ptc-5060979
on
05-03-2018
05:14 AM
Latest post on
10-17-2019
01:48 AM
by
vicky
11 Replies
5516
Views
|
hello everybody i have a problem with advanced framework extintion (AFX)
that is some dialog boxes a...
|
11 Replies
|
5516
Views
| |
| |
Hi All, I have set a font for drafting but while taking the print outs
the font is different from wh...
|
3 Replies
|
503
Views
| |
