cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 

Community Tip - Learn all about PTC Community Badges. Engage with PTC and see how many you can earn! X

Creo Simulate contact analysis

Go to solution
ilyachaban
14-Alexandrite
14-Alexandrite
‎Feb 17, 2023 03:19 AM
‎Feb 17, 2023 03:19 AM

Creo Simulate contact analysis

Hello, I'm trying to create and simulate contact analysis on mounted parts there are 6 main frames, 12 bolts and 4 pins with around 20 contacts defined. 

simulation doesn't converge at all. everything i've tried didn't get me anywhere always contact area is dancing around and residual factor too. 

I'm sure that I have defined all the contacts in all the places. All the frames are modelled as 1 part and all the bolts has slight interpenetration to create pretension. But it doesnt converge at all. 

Is there any good practice how to create contact simulation with many contacts? \

 

 

Things that i've tried: create pretension, delete pretension, fine mesh, rough mesh, change parameter called sim_contact_tolerance_factor increase/decreace, change convergence settings, finite friction, infinite friction, 0 friction, 

Example of convergence:

 

 

 

   Load factor            :     1.00000e-01
   Residual norm tolerance:     1.00000e-09

------------------------------------------
Iteration    Residual norm      Area
------------------------------------------
    1          1.0000e+00      7.0615e+04   Fri Feb 17, 2023   06:51:17
    2          1.0000e+00      4.5168e+05   Fri Feb 17, 2023   06:51:56
    3          1.0063e-03      3.4800e+05   Fri Feb 17, 2023   06:52:35
    4          1.3636e-06      2.9005e+05   Fri Feb 17, 2023   06:53:14
    5          1.5219e-07      2.6358e+05   Fri Feb 17, 2023   06:53:53
    6          7.2918e-07      2.1785e+05   Fri Feb 17, 2023   06:54:33
    7          3.9976e-08      1.8730e+05   Fri Feb 17, 2023   06:55:12
    8          2.2661e-08      1.7018e+05   Fri Feb 17, 2023   06:55:50
    9          1.0919e-08      1.7080e+05   Fri Feb 17, 2023   06:56:29
   10          5.4540e-09      1.6276e+05   Fri Feb 17, 2023   06:57:08
   11          3.2743e-09      1.5247e+05   Fri Feb 17, 2023   06:57:46
   12          4.0881e-09      1.4957e+05   Fri Feb 17, 2023   06:58:24
   13          6.8582e-05      1.8358e+05   Fri Feb 17, 2023   06:59:05
   14          1.0554e-08      1.7415e+05   Fri Feb 17, 2023   06:59:44
   15          4.1022e-07      1.5177e+05   Fri Feb 17, 2023   07:00:23
Loosening gap stiffness to improve convergence
   16          2.3832e-07      1.4155e+05   Fri Feb 17, 2023   07:01:02
   17          1.7176e-08      2.9714e+05   Fri Feb 17, 2023   07:01:41
   18          2.0151e-07      2.6400e+05   Fri Feb 17, 2023   07:02:20
   19          6.1776e-09      2.4227e+05   Fri Feb 17, 2023   07:02:59
   20          1.1068e-09      2.5557e+05   Fri Feb 17, 2023   07:03:41
   21          1.1850e-09      2.3187e+05   Fri Feb 17, 2023   07:04:23
   22          7.6003e-10      2.4082e+05   Fri Feb 17, 2023   07:05:05
Adjusted gap stiffness to prevent interpenetration
   23          2.7779e-08      2.2493e+05   Fri Feb 17, 2023   07:05:47
   24          3.6278e-09      2.1695e+05   Fri Feb 17, 2023   07:06:29
   25          3.0372e-09      2.0945e+05   Fri Feb 17, 2023   07:07:10
   26          9.6627e-10      2.1422e+05   Fri Feb 17, 2023   07:07:52
Adjusted gap stiffness to prevent interpenetration
   27          1.5556e-07      2.0513e+05   Fri Feb 17, 2023   07:08:34
   28          1.7384e-08      2.0158e+05   Fri Feb 17, 2023   07:09:16
   29          5.1700e-09      1.8797e+05   Fri Feb 17, 2023   07:09:58
   30          3.3820e-09      1.9962e+05   Fri Feb 17, 2023   07:10:37
   31          5.6008e-09      2.1553e+05   Fri Feb 17, 2023   07:11:20
   32          9.8902e-08      2.0151e+05   Fri Feb 17, 2023   07:12:02
   33          1.2410e-08      2.1347e+05   Fri Feb 17, 2023   07:12:44
   34          2.0315e-08      1.9927e+05   Fri Feb 17, 2023   07:13:29
   35          2.4502e-08      1.9847e+05   Fri Feb 17, 2023   07:14:14
   36          2.1911e-08      2.0351e+05   Fri Feb 17, 2023   07:14:56
   37          1.3892e-08      1.8761e+05   Fri Feb 17, 2023   07:15:38
   38          1.7767e-08      1.8462e+05   Fri Feb 17, 2023   07:16:23
   39          3.3594e-08      1.9113e+05   Fri Feb 17, 2023   07:17:05
   40          2.0919e-08      1.8388e+05   Fri Feb 17, 2023   07:17:48
   41          1.7216e-08      1.7961e+05   Fri Feb 17, 2023   07:18:34
   42          1.9691e-08      1.8318e+05   Fri Feb 17, 2023   07:19:15
   43          1.4191e-08      2.2937e+05   Fri Feb 17, 2023   07:19:57
   44          1.9441e-08      2.1013e+05   Fri Feb 17, 2023   07:20:38
   45          4.6010e-08      2.0278e+05   Fri Feb 17, 2023   07:21:20
   46          6.4672e-08      2.1654e+05   Fri Feb 17, 2023   07:22:01
   47          2.6309e-08      1.9879e+05   Fri Feb 17, 2023   07:22:42
   48          2.5303e-08      1.9170e+05   Fri Feb 17, 2023   07:23:23
   49          1.7855e-08      1.8747e+05   Fri Feb 17, 2023   07:24:04
   50          2.2876e-08      1.8581e+05   Fri Feb 17, 2023   07:24:47
   51          1.7156e-08      2.1835e+05   Fri Feb 17, 2023   07:25:28
   52          1.9992e-08      1.9296e+05   Fri Feb 17, 2023   07:26:10
   53          1.5495e-08      1.8153e+05   Fri Feb 17, 2023   07:26:52
   54          1.7576e-08      1.8018e+05   Fri Feb 17, 2023   07:27:34
   55          2.1264e-08      2.0016e+05   Fri Feb 17, 2023   07:28:16
   56          5.7598e-08      2.1021e+05   Fri Feb 17, 2023   07:28:58
   57          5.1185e-08      2.0055e+05   Fri Feb 17, 2023   07:29:40
   58          2.7393e-08      1.9653e+05   Fri Feb 17, 2023   07:30:24
   59          1.8009e-08      2.2472e+05   Fri Feb 17, 2023   07:31:04
   60          2.1383e-08      1.9777e+05   Fri Feb 17, 2023   07:31:47
   61          1.5448e-08      2.7099e+05   Fri Feb 17, 2023   07:32:28
   62          2.2027e-08      2.1360e+05   Fri Feb 17, 2023   07:33:09
   63          1.8144e-08      1.9227e+05   Fri Feb 17, 2023   07:33:51
   64          2.0051e-08      1.8533e+05   Fri Feb 17, 2023   07:34:33
   65          1.5847e-08      1.8219e+05   Fri Feb 17, 2023   07:35:14
   66          1.7437e-08      1.8076e+05   Fri Feb 17, 2023   07:35:56
   67          1.5126e-08      1.7785e+05   Fri Feb 17, 2023   07:36:37
   68          2.0546e-08      1.7657e+05   Fri Feb 17, 2023   07:37:18
   69          1.6498e-08      1.7678e+05   Fri Feb 17, 2023   07:38:00
   70          1.8724e-08      1.7677e+05   Fri Feb 17, 2023   07:38:41
   71          1.1573e-04      2.1970e+05   Fri Feb 17, 2023   07:39:24
   72          4.8163e-08      2.4947e+05   Fri Feb 17, 2023   07:40:06
   73          2.3002e-08      2.3116e+05   Fri Feb 17, 2023   07:40:47
   74          2.4053e-08      2.1288e+05   Fri Feb 17, 2023   07:41:30
   75          2.0014e-08      1.9955e+05   Fri Feb 17, 2023   07:42:12
   76          1.3195e-06      2.0574e+05   Fri Feb 17, 2023   07:42:53
   77          3.2539e-08      2.0102e+05   Fri Feb 17, 2023   07:43:34
Loosening gap stiffness to improve convergence
   78          2.3099e-07      1.9458e+05   Fri Feb 17, 2023   07:44:15
   79          1.5378e-08      3.8771e+05   Fri Feb 17, 2023   07:44:57
   80          4.6065e-10      3.4422e+05   Fri Feb 17, 2023   07:45:38
Adjusted gap stiffness to prevent interpenetration
   81          1.0244e-05      3.2347e+05   Fri Feb 17, 2023   07:46:19
   82          1.5491e-08      3.1698e+05   Fri Feb 17, 2023   07:47:00
   83          3.6565e-09      2.9462e+05   Fri Feb 17, 2023   07:47:41
   84          6.8412e-06      2.9824e+05   Fri Feb 17, 2023   07:48:24
   85          1.1817e-08      2.9346e+05   Fri Feb 17, 2023   07:49:05
   86          2.5043e-09      2.8267e+05   Fri Feb 17, 2023   07:49:47
   87          6.8605e-06      3.0087e+05   Fri Feb 17, 2023   07:50:28
   88          1.1866e-08      2.9516e+05   Fri Feb 17, 2023   07:51:11
   89          1.0546e-09      2.7080e+05   Fri Feb 17, 2023   07:51:53
   90          3.8126e-10      2.6411e+05   Fri Feb 17, 2023   07:52:35
Adjusted gap stiffness to prevent interpenetration
   91          1.0846e-05      2.8424e+05   Fri Feb 17, 2023   07:53:17
   92          3.3304e-08      3.0010e+05   Fri Feb 17, 2023   07:53:59
   93          2.4314e-08      2.7980e+05   Fri Feb 17, 2023   07:54:43
   94          6.8635e-06      2.8386e+05   Fri Feb 17, 2023   07:55:27
   95          5.9190e-08      2.8131e+05   Fri Feb 17, 2023   07:56:12
   96          9.8588e-08      2.6766e+05   Fri Feb 17, 2023   07:56:54
   97          8.0458e-06      2.8834e+05   Fri Feb 17, 2023   07:57:36
   98          8.1294e-08      2.8023e+05   Fri Feb 17, 2023   07:58:19
   99          5.6426e-08      2.7309e+05   Fri Feb 17, 2023   07:59:00
  100          7.0291e-06      2.8284e+05   Fri Feb 17, 2023   07:59:41
  101          7.1255e-08      2.7621e+05   Fri Feb 17, 2023   08:00:22
  102          8.1001e-08      2.6611e+05   Fri Feb 17, 2023   08:01:07
  103          1.6458e-05      2.8637e+05   Fri Feb 17, 2023   08:01:48
  104          8.8166e-08      2.8570e+05   Fri Feb 17, 2023   08:02:30
  105          4.7127e-08      2.7471e+05   Fri Feb 17, 2023   08:03:11
  106          8.0635e-08      2.6558e+05   Fri Feb 17, 2023   08:03:52
  107          8.3996e-08      2.6504e+05   Fri Feb 17, 2023   08:04:33
  108          1.0161e-07      2.6241e+05   Fri Feb 17, 2023   08:05:16
  109          9.0707e-08      2.8402e+05   Fri Feb 17, 2023   08:05:58
  110          5.8664e-08      2.5479e+05   Fri Feb 17, 2023   08:06:39
  111          6.3605e-08      2.7803e+05   Fri Feb 17, 2023   08:07:19
  112          5.7070e-08      2.6285e+05   Fri Feb 17, 2023   08:08:00
  113          6.7747e-08      2.6181e+05   Fri Feb 17, 2023   08:08:41
  114          9.3685e-08      2.5727e+05   Fri Feb 17, 2023   08:09:23
  115          9.8192e-08      2.5920e+05   Fri Feb 17, 2023   08:10:04
  116          6.1752e-08      2.5765e+05   Fri Feb 17, 2023   08:10:45
  117          4.5283e-08      2.5537e+05   Fri Feb 17, 2023   08:11:27
  118          4.6889e-08      2.5467e+05   Fri Feb 17, 2023   08:12:09
  119          9.4066e-08      2.5475e+05   Fri Feb 17, 2023   08:12:51
  120          1.0892e-07      2.5518e+05   Fri Feb 17, 2023   08:13:33
  121          7.8654e-08      2.5502e+05   Fri Feb 17, 2023   08:14:15
  122          5.5850e-08      2.5414e+05   Fri Feb 17, 2023   08:14:58
  123          6.5924e-08      2.5416e+05   Fri Feb 17, 2023   08:15:40
  124          5.8445e-08      2.5608e+05   Fri Feb 17, 2023   08:16:23
  125          7.4771e-08      2.5475e+05   Fri Feb 17, 2023   08:17:04
  126          9.1982e-08      2.6044e+05   Fri Feb 17, 2023   08:17:46
  127          7.9292e-08      2.5720e+05   Fri Feb 17, 2023   08:18:28
  128          5.7563e-08      2.5723e+05   Fri Feb 17, 2023   08:19:11
  129          5.1478e-08      2.5630e+05   Fri Feb 17, 2023   08:19:52
  130          6.7792e-08      2.5582e+05   Fri Feb 17, 2023   08:20:35
  131          6.7552e-08      2.5458e+05   Fri Feb 17, 2023   08:21:19
  132          1.3451e-05      2.7547e+05   Fri Feb 17, 2023   08:22:01
  133          9.9186e-08      3.0008e+05   Fri Feb 17, 2023   08:22:43
  134          6.1487e-08      2.8062e+05   Fri Feb 17, 2023   08:23:26
  135          9.8840e-08      2.6977e+05   Fri Feb 17, 2023   08:24:08
  136          7.1119e-08      2.6732e+05   Fri Feb 17, 2023   08:24:50
  137          8.4347e-08      2.6239e+05   Fri Feb 17, 2023   08:25:34
  138          8.4888e-08      2.8356e+05   Fri Feb 17, 2023   08:26:16
  139          8.8095e-08      2.7001e+05   Fri Feb 17, 2023   08:26:58
  140          5.7661e-08      2.6567e+05   Fri Feb 17, 2023   08:27:40
  141          5.2874e-08      2.6346e+05   Fri Feb 17, 2023   08:28:22
Loosening gap stiffness to improve convergence
  142          2.4066e-07      2.5976e+05   Fri Feb 17, 2023   08:29:04
  143          1.8710e-08      4.2414e+05   Fri Feb 17, 2023   08:29:46
  144          1.4229e-11      3.7598e+05   Fri Feb 17, 2023   08:30:28
Adjusted gap stiffness to prevent interpenetration
  145          2.8200e-08      3.5965e+05   Fri Feb 17, 2023   08:31:12
  146          1.8107e-09      3.2997e+05   Fri Feb 17, 2023   08:31:55
  147          1.4521e-06      3.1972e+05   Fri Feb 17, 2023   08:32:37
  148          8.4482e-09      3.4040e+05   Fri Feb 17, 2023   08:33:19
  149          7.1332e-07      3.3546e+05   Fri Feb 17, 2023   08:34:01
  150          6.1081e-09      3.3426e+05   Fri Feb 17, 2023   08:34:48
  151          7.0771e-07      3.3504e+05   Fri Feb 17, 2023   08:35:31
  152          6.1759e-09      3.3538e+05   Fri Feb 17, 2023   08:36:14
  153          1.4985e-06      3.2793e+05   Fri Feb 17, 2023   08:36:57
  154          8.2031e-09      3.4151e+05   Fri Feb 17, 2023   08:37:40
  155          7.2095e-07      3.3592e+05   Fri Feb 17, 2023   08:38:23
  156          6.9027e-09      3.3350e+05   Fri Feb 17, 2023   08:39:03
  157          7.0358e-07      3.3479e+05   Fri Feb 17, 2023   08:39:46
  158          7.2600e-09      3.3489e+05   Fri Feb 17, 2023   08:40:29
  159          1.4456e-06      3.2722e+05   Fri Feb 17, 2023   08:41:11
  160          8.4897e-09      3.4237e+05   Fri Feb 17, 2023   08:41:55
  161          7.1577e-07      3.3672e+05   Fri Feb 17, 2023   08:42:37
  162          6.8557e-09      3.3388e+05   Fri Feb 17, 2023   08:43:20
  163          7.0876e-07      3.3475e+05   Fri Feb 17, 2023   08:44:03
  164          6.8628e-09      3.3492e+05   Fri Feb 17, 2023   08:44:45
  165          1.5032e-06      3.2760e+05   Fri Feb 17, 2023   08:45:29
  166          8.6942e-09      3.4225e+05   Fri Feb 17, 2023   08:46:14
  167          7.2145e-07      3.3608e+05   Fri Feb 17, 2023   08:46:59
Loosening gap stiffness to improve convergence
  168          4.9275e-08      3.3360e+05   Fri Feb 17, 2023   08:47:43
  169          7.1184e-08      4.3826e+05   Fri Feb 17, 2023   08:48:27
  170          9.7485e-10      4.1120e+05   Fri Feb 17, 2023   08:49:11
Adjusted gap stiffness to prevent interpenetration
  171          1.6248e-07      4.0265e+05   Fri Feb 17, 2023   08:49:56
  172          1.7094e-09      3.8165e+05   Fri Feb 17, 2023   08:50:40
  173          7.2348e-08      3.7901e+05   Fri Feb 17, 2023   08:51:24
  174          1.1007e-09      3.7317e+05   Fri Feb 17, 2023   08:52:06
  175          1.5279e-07      3.7274e+05   Fri Feb 17, 2023   08:52:48
  176          1.6686e-09      3.7340e+05   Fri Feb 17, 2023   08:53:32
  177          7.2210e-08      3.7132e+05   Fri Feb 17, 2023   08:54:16
  178          1.0986e-09      3.6944e+05   Fri Feb 17, 2023   08:55:01
  179          1.5281e-07      3.7019e+05   Fri Feb 17, 2023   08:55:45
  180          1.6672e-09      3.7186e+05   Fri Feb 17, 2023   08:56:29
  181          7.2214e-08      3.7710e+05   Fri Feb 17, 2023   08:57:14
  182          1.0986e-09      3.7342e+05   Fri Feb 17, 2023   08:57:59
  183          1.5281e-07      3.7270e+05   Fri Feb 17, 2023   08:58:45
  184          1.6673e-09      3.7354e+05   Fri Feb 17, 2023   08:59:30
  185          7.2205e-08      3.7138e+05   Fri Feb 17, 2023   09:00:14
  186          1.0987e-09      3.6952e+05   Fri Feb 17, 2023   09:00:59
  187          1.5281e-07      3.7012e+05   Fri Feb 17, 2023   09:01:45
  188          1.6670e-09      3.7182e+05   Fri Feb 17, 2023   09:02:27
  189          7.2211e-08      3.7710e+05   Fri Feb 17, 2023   09:03:10
  190          1.0986e-09      3.7343e+05   Fri Feb 17, 2023   09:03:52
  191          1.5281e-07      3.7269e+05   Fri Feb 17, 2023   09:04:35
  192          1.6673e-09      3.7355e+05   Fri Feb 17, 2023   09:05:16
  193          7.2205e-08      3.7141e+05   Fri Feb 17, 2023   09:05:58
Loosening gap stiffness to improve convergence
  194          1.3992e-08      3.6951e+05   Fri Feb 17, 2023   09:06:39
  195          1.5492e-08      4.8051e+05   Fri Feb 17, 2023   09:07:21
  196          3.0527e-10      4.6902e+05   Fri Feb 17, 2023   09:08:08

 

 

 

 

 

 

Labels:
0 Kudos
Notify Moderator
ACCEPTED SOLUTION

Accepted Solutions
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 06:38 AM
‎Feb 17, 2023 06:38 AM

example contact

View solution in original post

contact_test.zip
0 Kudos
Notify Moderator
24 REPLIES 24
EddyVE
11-Garnet
11-Garnet
(To:ilyachaban)
‎Feb 17, 2023 03:48 AM
‎Feb 17, 2023 03:48 AM

Can you post a few screenshots of your assembly? That would help us in understanding what you are trying to do.

0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:EddyVE)
‎Feb 17, 2023 04:22 AM
‎Feb 17, 2023 04:22 AM

sorry can't post screenshots here is a sketch of a half of it and some connections

Bolted connection

ilyachaban_1-1676625680311.png

pin connection

ilyachaban_2-1676625698780.png

 

rough sketch

ilyachaban_3-1676625721758.png

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 04:51 AM
‎Feb 17, 2023 04:51 AM

contacts are very complicated, please upload STEP

 

 

example_contact.zip
1213 KB
0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 17, 2023 05:54 AM
‎Feb 17, 2023 05:54 AM

Sorry wrong formulation. I can't post work that i'm doing

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 06:13 AM
‎Feb 17, 2023 06:13 AM

OK, I am going to build a simple example

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 06:38 AM
‎Feb 17, 2023 06:38 AM

example contact

contact_test.zip
0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 17, 2023 06:47 AM
‎Feb 17, 2023 06:47 AM

Simulation that has that many elements actually works. There is no problem for me to simulate 2 parts in contact but when there is more parts simulation doesn't converge at all. 

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 06:54 AM
‎Feb 17, 2023 06:54 AM

in the model there are contact gaps, depending on the absolute accuracy

0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 17, 2023 07:17 AM
‎Feb 17, 2023 07:17 AM

What do you mean by contact gaps

Is that it?

ilyachaban_0-1676636199512.png

 

If it is: how did you choose 0.015?

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 07:37 AM
‎Feb 17, 2023 07:37 AM

yes: contact gap 0.15 mm > absolute accuracy 0.1 mm

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:skunks)
‎Feb 17, 2023 07:38 AM
‎Feb 17, 2023 07:38 AM

sorry: contact gap 0.015 mm > absolute accuracy 0.01 mm

0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 17, 2023 07:39 AM
‎Feb 17, 2023 07:39 AM

Is there any literature that defines that or it is your expirience with PTC Creo Simulate?

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 07:57 AM
‎Feb 17, 2023 07:57 AM

literature in german ...

0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 17, 2023 07:59 AM
‎Feb 17, 2023 07:59 AM

Because I've seen in literature that creo converge easily if you turn on friction and create interpenetration. so cylindrical connection has some friction under the head and has something to prevent it from rotation.

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 17, 2023 08:54 AM
‎Feb 17, 2023 08:54 AM

turn on friction is completely wrong way

0 Kudos
Notify Moderator
SweetPeasHub
17-Peridot
17-Peridot
(To:skunks)
‎Feb 21, 2023 08:38 AM
‎Feb 21, 2023 08:38 AM

Many contacts in Creo is difficult.

One tip I have is for a pin, to add a low stiffness spring (red color) to add some constraint to an otherwise loose pin.

SweetPeasHub_0-1676986451103.png

 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:SweetPeasHub)
‎Feb 22, 2023 03:11 AM
‎Feb 22, 2023 03:11 AM

I developed something like this about 12-13 years ago

2023-02-22.png

321 KB
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 22, 2023 11:39 AM
‎Feb 22, 2023 11:39 AM

Hi, thank you for your tips about contact gaps and friction. For now I have working model that converges very quickly. I didn't see your tip about axial rotation tip but i will use it 100%.

What degrees of freedom does this spring limits all 3 or only in tangential direction? 

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:ilyachaban)
‎Feb 23, 2023 03:08 AM
‎Feb 23, 2023 03:08 AM

thanks,

for example

2023-02-23_Spring_Property.png

0 Kudos
Notify Moderator
skunks
18-Opal
18-Opal
(To:skunks)
‎Feb 23, 2023 04:04 AM
‎Feb 23, 2023 04:04 AM

only necessary degrees of freedom, so that no rigid body displacement and no rigid body rotation take place

0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:skunks)
‎Feb 23, 2023 06:39 AM
‎Feb 23, 2023 06:39 AM

Thank you

0 Kudos
Notify Moderator
ilyachaban
14-Alexandrite
14-Alexandrite
(To:SweetPeasHub)
‎Feb 22, 2023 11:40 AM
‎Feb 22, 2023 11:40 AM

Thank you. Will try this one too. Now with the help of @skunks my model is working.

0 Kudos
Notify Moderator
PP_10622270
3-Newcomer
3-Newcomer
(To:ilyachaban)
‎Mar 15, 2023 02:52 AM
‎Mar 15, 2023 02:52 AM

Hello,

I came here to say only  that solution worked for me thanks to the community and the members for the solution. please keep sharing such post here .

Notify Moderator
olivierlp
Community Manager
Community Manager
(To:PP_10622270)
‎Mar 15, 2023 11:59 AM
‎Mar 15, 2023 11:59 AM

Thank you for the appreciation, @PP_10622270, and welcome to the PTC Community!

Thanks also to all participants in this topic! 

Olivier
0 Kudos
Notify Moderator
Announcements


Contact Community Management
Top Tags