| |
Hello, In a transient thermal analysis, for a boundary convection
condition, give the possibilty to ...
|
2 Replies
|
2192
Views
| |
| |
Hello, my task is simple. I have 2 metal part with 1 interface between
them. The first body temperat...
|
5 Replies
|
3446
Views
| |
| |
Hello,I'm starting to use the mechanisms with Creo and would like to
play a kinematics with a bevel ...
|
14 Replies
|
13346
Views
| |
| |
I don't understand the problem...
|
1 Reply
|
2064
Views
| |
| |
I am trying to determine the best method for simulating an assembly with
pinned joints and hydraulic...
|
4 Replies
|
3259
Views
| |
| |
Hi , I have problem in my Creo where i am unable to view entire options
in pop-up windows and unable...
|
4 Replies
|
2643
Views
| |
|
by
psobejko
on
May 03, 2018
12:44 AM
Latest post on
Sep 21, 2018
08:46 AM
by
jbertels
1 Reply
1829
Views
|
I usually think that more users complain about the "traffic" light
indicator in Creo that shows the ...
|
1 Reply
|
1829
Views
| |
|
by
skesavan
on
Oct 04, 2016
06:55 AM
Latest post on
Sep 20, 2018
03:08 PM
by
getuj3
4 Replies
2921
Views
|
I need to analysis the stick and boom models. I have tried to do the
boom but stress is high in boom...
|
4 Replies
|
2921
Views
| |
| |
I have an assembly with a gusset bolted to a vertical beam. When I start
the analysis, I get an erro...
|
3 Replies
|
3439
Views
| |
| |
Hello, I try to push down the top part (see pict.). The inside of ring
part should contact with outs...
|
1 Reply
|
1303
Views
| |
|
by
skunks
on
Sep 07, 2018
07:14 AM
Latest post on
Sep 17, 2018
09:47 AM
by
skunks
2 Replies
1826
Views
|
results in creo 2 fatigue advisor: OK creo 3: wrong creo 4: wrong creo
5: wrong
|
2 Replies
|
1826
Views
| |
| |
Hello everybody,I wonder how can I make a function (for torque motors
and others) like this:f(theta)...
|
11 Replies
|
8857
Views
| |
| |
Hi Everyone, I am looking for a way to essentially generate a graph of
force balance (i.e. input and...
|
11 Replies
|
9842
Views
| |
| | |
4 Replies
|
3516
Views
| |
|
by
skunks
on
Aug 14, 2018
10:40 AM
Latest post on
Aug 31, 2018
04:38 AM
by
skunks
8 Replies
4328
Views
|
dynamic friction 0,05 (view in My Videos)
|
8 Replies
|
4328
Views
| |
| |
Hi, I have a Beam idealization helt at three points, at the ends and in
the middle. I then perform a...
|
2 Replies
|
1834
Views
| |
|
by
skunks
on
Aug 24, 2018
05:45 AM
Latest post on
Aug 27, 2018
08:30 AM
by
skunks
1 Reply
1311
Views
|
grey cast iron cap what is wrong?
|
1 Reply
|
1311
Views
| |
|
by
skunks
on
Aug 23, 2018
02:00 AM
Latest post on
Aug 23, 2018
11:44 AM
by
skunks
4 Replies
2235
Views
| |
4 Replies
|
2235
Views
| |
|
by
skunks
on
Aug 20, 2018
04:27 AM
Latest post on
Aug 22, 2018
08:40 AM
by
skunks
4 Replies
1915
Views
| |
4 Replies
|
1915
Views
| |
| | |
5 Replies
|
2578
Views
| |
| |
Hello I am new to mechanism. Can anyone guide me for sample tutorial on
the same? I would like to st...
|
0 Replies
|
1068
Views
| |
|
by
Nussic
on
Jun 15, 2018
11:03 AM
Latest post on
Aug 15, 2018
03:58 PM
by
cfdgeek
1 Reply
1919
Views
|
Hello, When using the Fluid Analysis i always get the message "Residual
is NaN!" after pressing exec...
|
1 Reply
|
1919
Views
| |
| |
I'm hoping someone can help me with this...I'm fairly new to Creo
simulate... I am trying to simulat...
|
2 Replies
|
2115
Views
| |
| | |
6 Replies
|
3275
Views
| |
|
by
ptc-2784098
on
Feb 04, 2019
12:26 PM
Latest post on
Aug 09, 2018
07:19 AM
by
mliska
4 Replies
18251
Views
|
I'm using a Lenovo Thinkpad T430s running Windows 7 Enterprise, Service
Pack 1. I installed Creo, bu...
|
4 Replies
|
18251
Views
| |
| | |
6 Replies
|
3653
Views
| |
| |
Hello, I have a simple mechanism with no interference and I had defined
a 3D contact on it. I run th...
|
1 Reply
|
1810
Views
| |
| |
I'm trying to analyse a shaft with various components assembled on it.
One of those is a nut, which ...
|
4 Replies
|
3853
Views
| |
| |
1. using parts supplied in differential_parts (STEP for those who do not
have CREO 5) 2. assemble th...
|
6 Replies
|
4144
Views
| |
| | |
1 Reply
|
1354
Views
| |
