Community Tip - Did you get called away in the middle of writing a post? Don't worry you can find your unfinished post later in the Drafts section of your profile page. X
2 Replies
1146
Views
| I'm trying to create a multiplier gear pair, with a ratio of 3:1. I have
modelled the gears and defi...
|
2 Replies
|
1146
Views
| ||
1 Reply
656
Views
| When opening what I believe is an older PROE version part, a "LEGACY
PRT" dialog box appears. What i...
|
1 Reply
|
656
Views
| ||
4 Replies
1290
Views
| Hi All im having a problem creating a mechanism. it consists of a worm
driven gear mounted on a shaf...
|
4 Replies
|
1290
Views
| ||
by
MICHAELPOTUMS
![]() ![]()
5 Replies
1263
Views
| Why the function fillet and chamfer are not available in the assembly
mode in Creo? This thread is i...
|
5 Replies
|
1263
Views
| ||
by
Inoram
![]() ![]()
3 Replies
942
Views
| Is it possible to pull this clip (blue) into the tube and see how the
legs move? Ultimately to test ...
|
3 Replies
|
942
Views
| ||
by
joshuataylor
![]() ![]()
11 Replies
2083
Views
| What verification software are you guys using? With PTC moving away from
Vericut we may consider oth...
|
11 Replies
|
2083
Views
| ||
2 Replies
1534
Views
| Hello, I have to find the tension in belt, in belt pulley mechanism...
This thread is inactive and c...
|
2 Replies
|
1534
Views
| ||
by
sdesaulles
![]() ![]()
3 Replies
1241
Views
| I'm currently trying to run Creo 3 on the above but an older model with
the 1Gb graphics card. It us...
|
3 Replies
|
1241
Views
| ||
IS THERE ANY TOOL FOR WARPAGE ANALYSIS IN PRO ENGINEER 5.0 This thread
is inactive and closed by the...
|
0 Replies
|
351
Views
| |||
2 Replies
7497
Views
| I can't use my right click n Creo 3.0 parametric. Can you help me ? This
thread is inactive and clos...
|
2 Replies
|
7497
Views
| ||
by
SandeepKadam07
![]()
0 Replies
364
Views
| I have created one solid part which is a rubber part. Can we use it in
mechanism and make it flexibl...
|
0 Replies
|
364
Views
| ||
by
ufrigge
![]()
0 Replies
295
Views
| Make' it any sense to move geometry free in then space??? This thread is
inactive and closed by the ...
|
0 Replies
|
295
Views
| ||
1 Reply
1010
Views
| Hi all. I've a question. Is possible nodes handle in Creo Simulate when
throw "Mesh/Run" inside "FEM...
|
1 Reply
|
1010
Views
| ||
2 Replies
3254
Views
| I recently updated my system to windows 10 from windows 7. On windows 7
I had the purge function but...
|
2 Replies
|
3254
Views
| ||
by
ptc-4136280
![]() ![]()
1 Reply
859
Views
| Good Morning, I was wondering if anyone uses the Change Request and
Change Notice function within Wi...
|
1 Reply
|
859
Views
| ||
by
vincecatlin
![]() ![]()
3 Replies
2338
Views
| The new right click menu is nice and big. It would be better if I could
eliminate all the stuff I do...
|
3 Replies
|
2338
Views
| ||
by
zuvgård
![]() ![]()
1 Reply
533
Views
| Hi I want to place an annotation feature on a part and when you click it
part of a surface should be...
|
1 Reply
|
533
Views
| ||
4 Replies
2881
Views
| OK I have a specific error that no one here at work has seen before. I
have a large model running a ...
|
4 Replies
|
2881
Views
| ||
1 Reply
784
Views
| Dear community, I have two plates and want to give bolted connection.
Now for bolted connection, we ...
|
1 Reply
|
784
Views
| ||
by
jbrodowski
![]() ![]()
4 Replies
988
Views
|
4 Replies
|
988
Views
| |||
by
pburke
![]() ![]()
4 Replies
1263
Views
| Hey Everyone, I get a fatal error whenever I am trying to check in a
part or assembly to Windchill. ...
|
4 Replies
|
1263
Views
| ||
8 Replies
5618
Views
| Anyone know of any tutorials for the Creo Parametric animation function?
There aren't any on PTC Uni...
|
8 Replies
|
5618
Views
| ||
1 Reply
1254
Views
| Hi, I'm trying to create some Force & Moment diagrams for a simply
supported beam, with a pin suppor...
|
1 Reply
|
1254
Views
| ||
by
dbower1
![]() ![]()
5 Replies
1751
Views
| Maybe I am not using the round feature properly... But If have a single
round feature that creates 7...
|
5 Replies
|
1751
Views
| ||
by
TomU
![]() ![]()
22 Replies
4156
Views
| Just saw this come through from PTC today. This is pretty huge. Multiple
sessions of Creo running on...
|
22 Replies
|
4156
Views
| ||
by
drodriguezortiz
![]() ![]()
2 Replies
1074
Views
| Hi People!I don't know why, but suddenly the cool background color (blue
degraded) from Simulate dis...
|
2 Replies
|
1074
Views
| ||
8 Replies
3117
Views
| Hello, I don't seem to understand why the results are as shown in the
attached picture. I'm performi...
|
8 Replies
|
3117
Views
| ||
3 Replies
4873
Views
| Hello, I would like to add contacts to my model. There is a part that
travels up an down a rod follo...
|
3 Replies
|
4873
Views
| ||
1 Reply
1325
Views
| Hi, I am new to Creo simulate. I just had question in my mind whether we
can import mesh file from o...
|
1 Reply
|
1325
Views
| ||
2 Replies
1012
Views
| Hi, I have case where I need to calculate effort required to rotate
platform about vertical pivot. P...
|
2 Replies
|
1012
Views
|
Subject | Author |
---|---|