thanks for your reply..yes i am using iso post processor..most of cycle .which i generate thru this pp is working fine ..except drilling taping reaming etc cycle...by default the current processor generate drilling cycle with this format.
%DRILLING_1 G71
N1 G40 G90
N2 G30 G17 X-100 Y-100 Z-75
N3 G31 G90 X100 Y100 Z3
N4 G17 T17 M6
N5 S3 M3
N6 G00 X31 Y-12 M8
N7 G00 Z20
N8 G83 P01 2 P02 -4 PO3 -1 P04 0 PO5 100
N9 G00 X31 Y-12 Z-8 M89
N10 G00 Y77 M99
N11 M9
N12 M5
N13 M30
N999999 %DRILLING_1 G71
but i dont want to use this canned cycle due to some restriction(2nd setup clearance not available ) in this format ..
..i am sending you conversational post processor which i want to use only for drilling taping and reaming purpose please if you can update it or guide me how i can update on below mention format
0 BEGIN PGM 201RM10 MM
1 BLK FORM 0.1 Z X-400 Y-400 Z-75
2 BLK FORM 0.2 X+400 Y+400 Z+3
3 TOOL CALL 1 Z S80
4 CYCL DEF 201 REAMING ~
Q200=3 ;SET-UP CLEARANCE ~
Q201=-30 ;DEPTH ~
Q206=30 ;FEED RATE FOR PLNGNG ~
Q211=0 ;DWELL TIME AT DEPTH ~
Q208=80 ;RETRACTION FEED RATE ~
Q203=+0 ;SURFACE COORDINATE ~
Q204=50 ;2ND SET-UP CLEARANCE
5 L Z+50 R0 F3500 M3
6 L X-262.99 Y-146.925 M99
7 L X-303.002 M99
8 L X-305.002 Y+130.225 M99
9 L X-228.002 Y+166.1 M99
9 L X-106.487 Y+157.861 M99
9 L X-29.002 Y+164.233 M99
9 L X+28.999 M99
9 L X+106.484 Y+157.861 M99
9 L X+227.999 Y+166.1 M99
9 L X+304.999 Y+130.225 M99
9 L X+302.999 Y-146.925 M99
9 L X+262.99 M99
10 L Z+50 R0 F3000 M2
11 END PGM 201RM10 MM..
right now conversational post processor output in below mention format
1 BEGIN PGM DRILLING_1-CONVERSATIONAL MM
2 TOOL DEF 17 L0 R0
3 TOOL CALL 17 Z S3
4 M3
5 M8
6 L Z-20 F M90
7 L X+31 Y-12 F M90
8 CYCL DEF 1.0 PECKING
9 CYCL DEF 1.1 SETUP 2.00
10 CYCL DEF 1.2 DEPTH -4.00
11 CYCL DEF 1.3 PECKG 1.00
12 CYCL DEF 1.4 DWELL 0
13 CYCLE DEF 1.5 F100
14 L Z+10 R0 F M99
15 L Y+77 R0 F M99
16 L Z-20 F M90
17 M9
18 M5
19 M30
20 END PGM MM
hope you will understand..also attach creo mfg test model files and both iso and conversational pp
regards
FISA
