cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Showing results for 
Search instead for 
Did you mean: 

Community Tip - Did you get called away in the middle of writing a post? Don't worry you can find your unfinished post later in the Drafts section of your profile page. X

solving numerically the frequency and mode of the problem

Jslim_104115
6-Contributor

solving numerically the frequency and mode of the problem

Dear forum

 

In Euler-bernoulli theory, I am solving numerically the frequency and mode of the problem in which both ends are supported by springs in the vertical sagging of beams. Through this, the mode of the continuous beam is intended to be represented as a picture.

In the paper for reference, the angular frequency was calculated using MATLAB's system variable 'K' and "Inline function".

 

MATLAB from reference.

Jslim_104115_0-1701070038879.png

reference) Impacts of various boundayr conditions on beam vibrations. Ye Tao, 2015

My code is as attached.  I need help on how to implement this with MATCAD. When trying to implement using MATHCAD in the same way, it is difficult to solve the equation using a function and find each solution as the number of frequencies increases. Inquire about how to apply the function to this.

ACCEPTED SOLUTION

Accepted Solutions

A good reason to state the version level when you post a file--later versions can read earlier but early can't read later.  Attached pdf version, mods aren't challenging.  Note Werner's improvements!

View solution in original post

9 REPLIES 9

You've run afoul of Prime's dreaded labels problem, some of your K's show as bold blue--Prime thinks they're a unit rather than a variable.

 

You can plot the determinant of a matrix for each value of K, then solve for the roots of that equation.  Example in P9 attached (without roots.)

Some observations:

Werner_E_1-1701101386941.png

Werner_E_2-1701101547962.png

Werner_E_3-1701101618505.png

etc.

Werner_E_5-1701101907685.png

 

 

 

 

 

 

Jslim_104115
6-Contributor
(To:Werner_E)

Thank you very much for your response. I tried to apply the method of giving a specific range and solving the solution like your method, but I still think we need to organize more to apply the method of doing the harm and solving (understood like the false position root finding method) like the attachment.It is still difficult to find the determinant, and to find the value for each mode.

Thank you very much for your response. Unfortunately, I can't see your solution because it's a high version of the mathcad file, but I've solved it as much as I can as the attachment. It is still difficult to find the determinant, and to find the value for each mode.

A good reason to state the version level when you post a file--later versions can read earlier but early can't read later.  Attached pdf version, mods aren't challenging.  Note Werner's improvements!

Thank you very much for your kindness and good teaching.

You still don't say which version of Prime you are using. The attached file is in format of Prime 6.

 

Its not clear to me which calculation you are trying to implement.

 

Here some remarks:

Werner_E_0-1701207887314.png

Werner_E_1-1701207943085.png

Werner_E_2-1701207977190.png

 

 

 

Werner_E_3-1701208052326.png

 

 

 

 

Werner_E
25-Diamond I
(To:Werner_E)

Here is a rudimentary function which tries to get all zeros of a given function within a certain interval.
Its not perfect and has its failures.

If you increase the number of steps so no not miss any zeros which are very close, you will probably end up with some duplicates.

The same applies if you decrease the value of the variable "zeroprecision".
After all the function uses the built-in numeric "root" function which has its precision limits. to increase it you may try assigning the system variable TOL a lower values than the default 10^-3.

Werner_E_2-1701211818543.png

 

You can now use this function to get all zeros of your determinant within a given interval and calculate the appropriate w -value:

Werner_E_1-1701211617875.png

Werner_E_3-1701212303265.png

Werner_E_4-1701212687049.png

 

Prime 6 file attached. Use at your own risk 😉

Jslim_104115
6-Contributor
(To:Werner_E)

I'm trying to press Accept solution, but I can't use it again.
Thank you very much for your kindness and good teaching.

Announcements

Top Tags