turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Community
- :
- PTC Mathcad
- :
- PTC Mathcad Questions
- :
- Re: Creation a plot with error bars (Y and X axis)

Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-16-2012
01:54 PM

09-16-2012
01:54 PM

Hello, Dear Mathcad users!

It's my first lessons on **mathcad prime 2.0, **and I'am trying to create a plot with error bars (Y and X axis).

I managed with Y-axis, but I cannot make the same on X-axis.

Could somebody help me how to do it?

The file I've created attached.

Andrey KIselev

Student of Moscow State University.

Solved! Go to Solution.

Labels:

1 ACCEPTED SOLUTION

Accepted Solutions

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-17-2012
10:17 AM

12 REPLIES

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-17-2012
10:17 AM

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-18-2012
09:56 AM

09-18-2012
09:56 AM

Thank you, Mr. Jackson.

It's a pity that the latest version of Mathcad can't manage with some old tasks.

But, nevertheless, you was wery helpfull.

Best reguards, Andrey.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-30-2014
01:20 PM

09-30-2014
01:20 PM

Hi Richard/All,

Does anyone know if this has been fixed in Mathcad Prime 2.0 yet?

I am planning to have my students use Mathcad to do their physics lab write-ups and error bars (both x and y) would be really useful!

Also does anyone know how to do the maximum and minimum slopes of the lines of best fit that pass through all the error bar lines (for example, see attached picture)?

Thanks,

Benson

Highlighted
##
##### Re: Creation a plot with error bars (Y and X axis)

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-30-2014
01:33 PM

09-30-2014
01:33 PM

ps - anyone got any ideas on how to represent/deal with uncertainties in measured values that you put into a data table using the "insert table" feature?

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-30-2014
01:47 PM

09-30-2014
01:47 PM

Does anyone know if this has been fixed in Mathcad Prime 2.0 yet?

The x and y error bars can actually be made to work in Prime. Put the cursor in Re(xBars) on the graph axis and change the plot type to waterfall trace. Then do the same for Re(yBars).

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-30-2014
02:20 PM

09-30-2014
02:20 PM

Also does anyone know how to do the maximum and minimum slopes of the lines of best fit that pass through all the error bar lines (for example, see attached picture)?

Here are worksheets that show how to fit a line to data with errors in both x and y (there is no built-in Mathcad function to do it) and how to calculate the errors in the fitted parameters (this worksheet was taken from the Data Analysis Extension Pack in MC15). Unfortunately, the error calculation assumes errors in y only, and I don't have a worksheet that shows how to do these calculations when there are errors in both x and y. The Mathcad Prime files are for Prime 3.0 (sorry, I have no way to convert to Prime 2.0 format). The Data Analysis Extension Pack didn't convert perfectly, but it could be fixed.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

10-01-2014
09:09 AM

10-01-2014
09:09 AM

Hi Richard,

Thanks so much for responding!

Just a few follow-up questions though:

-what do you mean by "Re(xBars)" and "Re(yBars)"?

-the academic version I get as part of the PTC Schools programe is Prime 2.0. Is it possible for you to post .XPS file exports or screenshots so I can see what method you used?

-finally, any idea how to put the +/- uncertainty into a table of values created by using the "insert table" feature? Because the format seems to be fixed as <variable1> <units1> , <variable2> <units2> etc, so you can put x (s) and y (m) but not x (+/- 0.1s) and y (+/- 0.01m) for example. I guess worst case you could add separate columns for the upper and lower uncertainty bounds, right?

Cheers,

Benson

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

10-01-2014
04:26 PM

10-01-2014
04:26 PM

-what do you mean by "Re(xBars)" and "Re(yBars)"?

That's actually very obvious if you look in the worksheets.

-the academic version I get as part of the PTC Schools programe is Prime 2.0. Is it possible for you to post .XPS file exports or screenshots so I can see what method you used?

Your Prime 2.0 license file will work for Mathcad 15, which you can get here: http://www.ptc.com/product/mathcad/free-trial/thank-you. If you have Mathcad 15 installed you will also have a converter installed that will convert the Mathcad 15 files to Prime 2.0 files (although you will have to do a couple of fixes after the conversion).

I guess worst case you could add separate columns for the upper and lower uncertainty bounds, right?

That's the only way I can think of.

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

10-12-2014
04:15 AM

10-12-2014
04:15 AM

Hi Richard,

Thanks again for the clarification.

I've now upgraded to Mathcad Prime 3.0 and opened the files that you attached, but there does seem to be quite a few problems with the formatting, and I can't find a reference to Re(xBars) or Re(yBars) anywhere. Moreover, the statistical methods used in those sheets are far too complicated for what we need to do in IB DP Physics.

Basically, all I need is a simple example, showing how data with uncertainties could be put into a table and then plotted with error bars and max and min slope lines of best fit. In other words, something just like the below example, but augmented to include uncertainty data, error bars in x and y and max and min slope lines of best fit (and with slightly less scatter in the data, of course!).

Do you (or does anybody out there) have something like that you could share?

Thanks!

Benson

Announcements

____________________________________ If you experience problems when attaching a Mathcad sheet file ( .mcd, .xmcd or .mcdx) to the message then zip it first. To get the .zip file, use Windows Explorer, select the sheet file, right-mouse click and select "Send to" then "Compressed (zipped) folder". This results in a .zip file containing the worksheet that you can attach

Top Tags