Get Help

Turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Community
- :
- PTC Mathcad
- :
- PTC Mathcad
- :
- Re: I want to know 'How to combine two 3D plots in...

Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

09-14-2017
11:28 PM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-14-2017
11:28 PM

I want to know 'How to combine two 3D plots in a single 3D plot'

Dear all,

I want to combine two 3D plots (M, N, V) and (M1, N1, V1)

into a single 3D plot in Mathcad.

I attached my code below.

Could anyone help me

Thanks.

Solved! Go to Solution.

1 ACCEPTED SOLUTION

Accepted Solutions

09-15-2017
06:06 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
06:06 AM

@terryhendicott wrote:

Hi,

You are plotting way too many points in the combined plot 400,002 points. This will take Mathcad forever to plot.

Enclosed is a program that samples every five points of M,N,V and M1,N1,V1 into shorter arrays Ms,Ns,Vs, and Ms1,Ns1,Vs1. It takes Mathcad minutes to show finally the plots of these two curves in a 3D plot. Each plot can have its own appearance. Here I chose red and blue scatter plots. I am not sure how long it will take if you leave MathCad to plot the 400,002 points

The bottom left of the 3d graph is like this (Ms,Ns,Vs),(Ms1,Ns1,Vs1) Hope this helps

Without undue difficulties, we can do a quick calculation if you reduce the number of integration steps.

Viktor

6 REPLIES 6

09-15-2017
04:56 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
05:33 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
05:33 AM

Hi,

You are plotting way too many points in the combined plot 400,002 points. This will take Mathcad forever to plot.

Enclosed is a program that samples every five points of M,N,V and M1,N1,V1 into shorter arrays Ms,Ns,Vs, and Ms1,Ns1,Vs1. It takes Mathcad minutes to show finally the plots of these two curves in a 3D plot. Each plot can have its own appearance. Here I chose red and blue scatter plots. I am not sure how long it will take if you leave MathCad to plot the 400,002 points

The bottom left of the 3d graph is like this (Ms,Ns,Vs),(Ms1,Ns1,Vs1) Hope this helps

09-15-2017
06:06 AM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
06:06 AM

@terryhendicott wrote:

Hi,

You are plotting way too many points in the combined plot 400,002 points. This will take Mathcad forever to plot.

Enclosed is a program that samples every five points of M,N,V and M1,N1,V1 into shorter arrays Ms,Ns,Vs, and Ms1,Ns1,Vs1. It takes Mathcad minutes to show finally the plots of these two curves in a 3D plot. Each plot can have its own appearance. Here I chose red and blue scatter plots. I am not sure how long it will take if you leave MathCad to plot the 400,002 points

The bottom left of the 3d graph is like this (Ms,Ns,Vs),(Ms1,Ns1,Vs1) Hope this helps

Without undue difficulties, we can do a quick calculation if you reduce the number of integration steps.

Viktor

09-15-2017
07:35 PM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
07:35 PM

Thanks a lot Viktorrobov for your reply.

But, I have some doubt in plotting 2 3D plots.

When I draw 2 3D plots, plot 1 is plotted using lines from appearence tab

and the plot 2 is plotted using wireframe from appearence tab.

In the appearence tab, I can't find lines option in plot 2.

I want to know, 'How to choose lines options for plot 2 from the appearence tab ?'

In plot 1, I saw the following in the appearence tab,

Line options

* Lines

* Contour lines

*No lines

whereas in plot 2, I saw the following,

Line options

*Wireframe

*contour Lines

*No lines

I can't find lines option in plot 2.

How to choose lines from the appearence tab in plot ?

I attached the code here.

09-15-2017
08:57 PM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
08:57 PM

Hi,

The lines options on the appearance tab change depending on what is selected in the generals tab.

You have for plot one scatter plot and for plot two surface plot. This gives you the two different lines options.

09-15-2017
07:19 PM

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

09-15-2017
07:19 PM

Thanks a lot terryhendicott for your reply.