2 Replies 1169 Views
Hi, I have question if is possible in terminal table to use value with spaces. Example: | SET | | PI...
by PetePickettII on 12-11-2019 11:12 PM
0 Replies 157 Views
There is very little documentation on this. I have a simple block (in wiring diagram) with 5 ports o...
I am attempting to share a network between several cables so they can all route together in a bundle...
I created a pipe. The points used to route were referencing another assembly and using existing axis...
Hello,I try to auto associate the ECAD Schematic & Board in Ecad Neutral WGM.We use the non separabl...
by PetePickettII on 10-23-2019 09:20 AM
0 Replies 175 Views
Once our drawings are done, our harness mfg facility exports it to Autocad and adds the following mf...
Hi, I am searching for a way to delegate the Windchill Version and the Windchill LifeCycle state to ...
To all, I am using CREO 3.0 M090. When I route a cable or wire using a network everything is fine. W...
2 Replies 1092 Views
I am attempting to build up a new Connector Shape in Creo Schematics that will support adding Backsh...
Can we able to defined the length of cable in creo schematic?
Hi, everyone. A client asked me about something and I haven't been able to get the problem out of my...
Trying to open a file and get an error message "Cabling harness cannot be retrieved in this mode" Wh...
2 Replies 418 Views
Hello, I have started using Creo Schematics 4.0 recently for Cabling, BOM generation(.csv), Harness ...
Hi!I have a quite big wiring design going on, of a harness so big, it won't fit on any of my current...
1 Reply 407 Views
I'm fairly a beginner for both Cabling and Schematics and need to help company up these programs to ...
Hello,I have a 2D library that I would like to import as central catalog in schematics. Problem is I...
3 Replies 479 Views
Is there a way to tell the name of the cabling assembly that created a wire part from the part only?...
by BillF on 08-05-2019 11:46 AM
0 Replies 305 Views
If the Parameter pane is open, using Refit Sheet to view the entire sheet defaults to zooming it to ...
2 Replies 439 Views
Schematics can output a .eda file that Creo View can use. Can this file be created or viewed by any ...
This is a non-spec driven piping question, if that matters. There's been a design change, requiring ...
1 Reply 680 Views
Hi, I am working with a lot of hoses, I need to create drawings for them. Drawing contains a table w...
hi all, How can I replace a fitting by pipe diaemeter? I can't find the relection using pro/program
Has there been any advancement on this issue? It has been 4 years since this post. I am still in sea...
Hi.. I have created one pipe by creo - piping module and added some insulation, Now i want to find i...
by Ramesh_Mani on 06-11-2019 09:07 AM
0 Replies 438 Views
Greetings, In Pro-diagram - We used to select the one or more highways at a time using the drop down...
Our cables are routed and then each leg length is fixed. Sometimes if modifications are made to the ...
I have been using cross sheet graphics to break a design into multiple sheets and to reduce the clut...
Can anyone tell me how to show twisted wires in Pro-E? I took the PTC training course on Cabling a f...
by ptc-4428911 on 05-29-2019 07:28 PM
0 Replies 354 Views
I'm fairly new to Creo cabling and right now is working on flatten harness. My harness part is simpl...
I had a user ask me how to show the harness length in a drawing note. The length can be shown in a t...