New to cabling! Creo 3.0. I created a network and can route (manually using via network) between con...
We have created a bend machine table and would like to use it on the drawing. However we would like ...
Where do I post for cabling? I don't see a 'label".
Hi, I am new to cable routing. Sort of. Used the old one a bit. Learning newer Creo 3 version. So I ...
Is this site still under fixation? I had to remove the "s" from "https" to get in. Otherwise i was g...
I am tyring to change the data type of a few attributes from "string" to "integer". We are using Cre...
by rmees-2 on 05-02-2018 07:27 PM
0 Replies 348 Views
Hi folks,I'm just sending this out here to see response. We partner with external tool design resour...
Hi everyone! After open some neutral (.neu) files and save them into a PRT model, I lost the ability...
With the posting about Pro/Intralink 3.3's timeout date being hit today, It raises a question.How ma...
Hello !I am pretty new to Creo. I have installed a PTC Creo parametric in my computer. It is pretty ...
The Cabling and Piping module in Creo helps you quickly create piping in your model. But what happen...
by as-5 on 05-02-2018 07:29 PM
0 Replies 263 Views
Dear Mr. Jim,1. The Creo Schematics version I'm working in is 3.0 with datecode M020.2. I've created...
If you use branching in Creo Schematic, how does Pro Cabling handle it to do the routing to the comp...
by rhahn-2 on 05-02-2018 07:29 PM
0 Replies 286 Views
Is there a way to get all of the common Entry Ports/Pins to show in the Parameter Editor? When I ope...
I am very new to creating harnesses and am trying to figure out how to change the routing of a wire ...
Hello,I am trying to remove a location in cabling but the following message appears on the bottom: "...
Sequence of Events:1. Create a 3-D cable in PRO/CABLE.2. Flatten that cable (create the .mfg file).3...
We're running Creo Schematics 3.0 M020 with Windchill WGM 10.2 M030-CPS22.We recently updated out WG...
Hi everyone, thanks for your help in advance.We are starting to migrate from using IDF transfer for ...
Hi everyone,someone knows how can I break dependency of locations for a cabling? I have a harness th...
1 Reply 473 Views
Schematics 2 - will update to Schematics 4 when we go to Windchill 11Occasionally I get the message:...
Hi All,When we create a harness and create new spools (Bundle coverings, conduits, tubes etc.) is th...
by sheidenreich on 12-12-2018 02:04 PM
0 Replies 616 Views
Comparing Cadence schematics. I point to the *.cpm file and Creo stops working.
2 Replies 1996 Views
Hello,I'm a user of Windchill (10.2) and I use the WorkGroup Manager of Windchill with Altium Design...
3 Replies 1563 Views
There is a fairly straightforward mechanism for sharing Windchill Attributes and their values betwee...
Hello,Job OpportunityI know that maybe this is the wrong place for this, but right now I am desperat...
2 Replies 789 Views
I have created a network and I'm trying to route cables using that network. Sometimes when routing a...
I finished piping root shown below.Please advice how to solve this problem
Hi all,do you know the logic ProE uses to name the Line Stock inside the model tree?I get the inform...
1 Reply 510 Views
I have a harness that is used in several applications. 95% of it is shaped exactly the same between ...