Get Help

Turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Community
- :
- Creo Parametric
- :
- Simulation
- :
- Re: Symmetry Boundary Condition in Thermal Mode 6....

Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

Highlighted

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-26-2020
01:38 AM

02-26-2020
01:38 AM

Hello Community,

right now I'm trying to compose a thermal Model which I want to model using a symmetric boundary condition. I've read about thermal symmetric boundary condtions in the Documentation for Simulate 5.0 but can't seem to find it in 6.0? Was it taken out? Is there a workaround?

Thanks in advance 🙂

SNC

Solved! Go to Solution.

Labels:

1 ACCEPTED SOLUTION

Accepted Solutions

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-27-2020
06:15 AM

02-27-2020
06:15 AM

7 REPLIES 7

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-26-2020
11:31 PM

02-26-2020
11:31 PM

Re: Symmetry Boundary Condition in Thermal Mode 6.0

Are you looking for this symmetry?

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-27-2020
02:11 AM

02-27-2020
02:11 AM

Re: Symmetry Boundary Condition in Thermal Mode 6.0

I remind you that using 3D symmetric BCs (outside "2D symmeties") you need also to physically cut the parts.

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-27-2020
04:10 AM

02-27-2020
04:10 AM

Re: Symmetry Boundary Condition in Thermal Mode 6.0

Kind of. Im looking for the "Mirror Symmetry". The one you showed me is the cyclic one, which I can find in my model to. However in my mechanical Models I'm using mirror symmetry a lot. Now I wand to use a thermal study for a MEC/T Load and I would love to have the mirror symmetric boundary condition in thermal too.

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-27-2020
06:15 AM

02-27-2020
06:15 AM

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-28-2020
01:17 AM

02-28-2020
01:17 AM

Re: Symmetry Boundary Condition in Thermal Mode 6.0

Ah okay. Thanks a lot. At least I know for sure, that there is no mirror symmetry in the thermal module.

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-27-2020
06:48 AM

02-27-2020
06:48 AM

Re: Symmetry Boundary Condition in Thermal Mode 6.0

i believe if you do not put any boundary condition in thermal on the symmetry plane the results will be valid for symmetry. in structural side for load due to thermal the structural symmetry constraint is needed and available to choose. Does this make sense? try some simple model to be convinced. with and without symmetry cut.

Highlighted
##

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Notify Moderator

02-28-2020
01:15 AM

02-28-2020
01:15 AM

Re: Symmetry Boundary Condition in Thermal Mode 6.0

Okay that's interesting. I was under the impression that you would have to use the exact same model in both analysis. I will try to compute a thermal calculation with a "full" modell and import those results into the mechanical module where I've loaded the "half" model.