Windchill Matrix
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
Windchill Matrix
Hi Guys,
I am looking for a CAD compatibility matrix for Windchill 11.0 M030 CPS 22. If any one has kindly shared with me.
Regards,
Aj
Solved! Go to Solution.
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
I do have an older version of the matrix that clearly shows Windchill 11.0 M030 is only supported up to Creo 6, as I listed in my comment above. I was looking at that chart when I wrote my earlier response.
Like jbailey said, Creo 7 may work, but it is not supported with Creo 7.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
thanks for the replay @avillanueva
which Creo Parametric we can use in Windchill 11.0 M030 CPS22.
Aj
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
Thanks for the replay @jbailey How we can find it like if it's CPS 10 which version of Creo we can use and CPS22 which one we required like that. How we can find it.
Aj
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
This is probably the best matrix you are going to get...
https://www.ptc.com/support/-/media/support/refdocs/Pro_INTRALINK_8,-d-,x/11,-d-,1/WindchillCreoSWCompatibility11x_168117.pdf?sc_lang=en
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
sorry to say here i can only see upto CPS 14, i want CPS22 also
Creo 6.0 support with Windchill 11.0 requires as a minimum Windchill 11.0 M030 CPS14 refer page 12.
Aj
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
You can use any release of Creo 6 with Windchill 11.0 M030 CPS14 and higher. Your use of CPS22 will be fine with any release of Creo 6.
You cannot use any higher versions of Creo with Windchill 11.0 M030.
To use a higher version of Creo, you will need to upgrade Windchill.
Windchill 11.1 can be used with Creo 7 & Creo 8, along with Creo 6.
Windchill 11.2 is the same.
Windchill 12.0 removes support for Creo 6 and adds support for Creo 9 and Creo 10.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
Thanks for sharing @BenLoosli
But i thing we can use Creo 7 also but i can't find any matrix for that.
Aj
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
It may work, but it is not supported.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Notify Moderator
I do have an older version of the matrix that clearly shows Windchill 11.0 M030 is only supported up to Creo 6, as I listed in my comment above. I was looking at that chart when I wrote my earlier response.
Like jbailey said, Creo 7 may work, but it is not supported with Creo 7.