Creo 7.0 License Troubles

[MB_9792676]

After looking at many questions and solutions posted here, I finally give up.

The license I requested does not seem to work properly with my Creo version. I have tried the key I am supposed to use, two others from the forum, the license files from my email are also added.

What else can I do?

This is the second machine I am trying this install. On the other it worked fine - is there a way to port the license in case it is restricted to one machine?

Thanks in advance,

Moritz

[IM_9837839]

I'm having the same problem with that same code.

[MartinHanak]

---

@MB_9792676 wrote:

After looking at many questions and solutions posted here, I finally give up.

The license I requested does not seem to work properly with my Creo version. I have tried the key I am supposed to use, two others from the forum, the license files from my email are also added.

What else can I do?

This is the second machine I am trying this install. On the other it worked fine - is there a way to port the license in case it is restricted to one machine?

Thanks in advance,

Moritz

---

Hi,

please run following command in Command prompt window on problematic computer and upload ip.txt file.

ipconfig /all > ip.txt

[MB_9792676]

Hi,

I have attached the ip.txt below.

[MartinHanak · Accepted solution]

---

@MB_9792676 wrote:

Hi,

I have attached the ip.txt below.

---

Hi,

C:\ProgramData\PTC\Licensing\sw_license_email_5091498.dat

• license is generated for different computer
• you cannot use this license file

C:\ProgramData\PTC\Licensing\sw_license_email_5154635.dat

• license is generated for your computer
• license contains Creo Parametric 6.0 license (CREOPMA_SchoolSTD6, version 37.0)
• you cannot use this license file

C:\ProgramData\PTC\Licensing\BK700908EDSTUDENTEDUNI_license.dat

• license is generated for your computer
• license contains Creo Parametric 7.0 license (CREOPMA_Student6, version 38.0)
• you CAN use this license file

1.] open parametric.psf file in Notepad (it is located in Parametic\bin subdirectory in Creo installation)

2.] check/modify two following lines

ENV=PTC_D_LICENSE_FILE-=C:\ProgramData\PTC\Licensing\BK700908EDSTUDENTEDUNI_license.dat

ENV=CREOPMA_FEATURE_NAME=CREOPMA_Student6 ()

3.] run Creo

[MB_9792676]

Thank you, this has worked flawlessly for Parametric, Layout and Simulate.

ENV=PTC_D_LICENSE_FILE-=C:\ProgramData\PTC\Licensing\BK700908EDSTUDENTEDUNI_license.dat

ENV=CREOPMA_FEATURE_NAME=CREOPMA_Student6 ()

For Direct, I had to change the following:

ENV=PTC_D_LICENSE_FILE-=C:\ProgramData\PTC\Licensing\BK700908EDSTUDENTEDUNI_license.dat

ENV=CREOPMA_FEATURE_NAME=CREODMA_Student3 ()

since that is what my license file includes.

Thank you!

[GD_9838213]

Hello, I have the same problem, when I open creo I read the same message that I attach. 

I've read and tried the solution that you suggest but I don't know what is the file named ip.txt. 

Could you help me? 

Thanks

[MartinHanak]

---

@GD_9838213 wrote:

Hello, I have the same problem, when I open creo I read the same message that I attach. 

I've read and tried the solution that you suggest but I don't know what is the file named ip.txt. 

Could you help me? 

Thanks

---

Hi,

license file mentioned on the picture contains Creo 6.0 license. Unfortunatelly you are using it to launch Creo 7.0.