MULTAX Errors

ScottJohnson · ‎Mar 03, 2017

When I post out MULTAX I get:I have issues now when posting MULTAX vs ROTATE.

When I post out ncl for ROTATE I get:

N52 G3 X88.669 Y700.92 I0 J-31.75

N53 G1 Y519.508

N54 X-384.9

N55 Z239.2

N56 G0 X358.3 Y821.57

N57 G1 Z227.008

N58 X-128.32

N59 G3 X-229.92 Y719.932 I0 J-101.6

N60 G1 X-229.782 Y348.712

N61 G3 X-128.182 Y247.15 I101.6 J.038

N62 G1 X87.087

N63 G3 X188.604 Y344.649 I0 J101.6

N64 G1 X202.943 Y699.639

N65 G3 X171.219 Y732.67 I-31.724 J1.281

N66 G1 X120.419

N67 G3 X88.669 Y700.92 I0 J-31.75

N68 G1 Y519.508

N69 X-384.9

N70 Z369.28

When I post out MULTAX I get:

N67 G3 X88.669 Y700.92 I0 J-31.75

N68 G1 Y519.507

N69 X-384.9

N70 Z369.28

N71 G0 X-408.727 Y502.998 Z342.721 B7.334

N72 X-401.695 Y486.481 Z350.936 B19.668

N73 X-331.864 Y469.967 Z417.59 B41.222

N74 X-167.123 Y453.454 Z506.542 B72.607

N75 X-15.116 Y436.933 Z533.185 B100.417

N76 X37.598 Y420.415 Z532.072 B117.256

N77 X23.732 Y403.904 Z532.87 B126.932

N78 X-22.074 Y387.388 Z532.941 B133.182

N79 X-67.8 Y370.866 Z529.072 B139.427

N80 X-109.283 Y354.351 Z522.083 B146.078

N81 X-147.763 Y337.839 Z512.524 B152.987

N82 X-184.867 Y321.319 Z500.338 B159.965

N83 X-222.123 Y304.8 Z484.95 B166.808

N84 X-260.679 Y288.288 Z465.362 B173.33

N85 X-300.986 Y271.773 Z440.366 B179.405

It is like it is reading ahead on RETRACT and anticipating a move to B180.

Same Creo file, just Use Rotation on or off. Seems to be in the .ncl somehow. Anyone else see this problem? Creo Parametric 2.0 Date Code M220.

AustinN.C.,Inc. · ‎Mar 03, 2017

Without seeing the NCL files and the LST file from the post it is hard to say for sure but I think this is the post doing linearization. Do you have LINTOL/n in your NCL file of Linearization enabled in the post? If so you can turn it off and see if that changes the output.

Fred

ScottJohnson · ‎Mar 03, 2017

Hi Fred,

No LINTOL in the ncl. This is the section that gets goofy after MULTAX.

RAPID

MULTAX / ON

GOTO / -15.1535433071, 20.4530544432, 14.5385737003, $

0.0000000000, 0.0000000000, 1.0000000000

RAPID

GOTO / -17.6823706865, 19.8030691050, 11.3284437210, $

-0.1276563404, 0.0000000000, 0.9918184606

RAPID

GOTO / -19.5422928246, 19.1527798756, 7.6875439264, $

-0.3365628468, 0.0000000000, 0.9416610060

RAPID

GOTO / -20.6613454558, 18.5026178012, 3.7560489448, $

-0.6589746926, 0.0000000000, 0.7521651112

RAPID

GOTO / -20.9975670368, 17.8524975825, -0.3174907902, $

-0.9542776933, 0.0000000000, 0.2989215348

RAPID

GOTO / -20.5379371207, 17.2020868167, -4.3807879984, $

-0.9835171498, 0.0000000000, -0.1808148669

RAPID

GOTO / -19.2997707077, 16.5517616034, -8.2774774899, $

-0.8889730830, 0.0000000000, -0.4579594499

RAPID

GOTO / -17.3310732506, 15.9017391000, -11.8588116850, $

-0.7993479743, 0.0000000000, -0.6008683849

RAPID

GOTO / -14.7049775249, 15.2514876683, -14.9920317347, $

-0.7291792577, 0.0000000000, -0.6843227382

RAPID

GOTO / -11.5203752907, 14.6010078273, -17.5578570808, $

-0.6504192488, 0.0000000000, -0.7595754082

RAPID

GOTO / -7.9004988280, 13.9508096248, -19.4571238626, $

-0.5580608794, 0.0000000000, -0.8298000090

RAPID

GOTO / -3.9819673162, 13.3007277489, -20.6189664234, $

-0.4541952079, 0.0000000000, -0.8909021906

RAPID

GOTO / 0.0892534996, 12.6503517692, -20.9997683708, $

-0.3425874215, 0.0000000000, -0.9394859545

RAPID

GOTO / 4.1570157292, 11.9999884941, -20.5844096982, $

-0.2282204355, 0.0000000000, -0.9736094868

RAPID

GOTO / 8.0654538957, 11.3499221993, -19.3893690288, $

-0.1161436216, 0.0000000000, -0.9932324296

RAPID

GOTO / 11.6691725233, 10.6997073554, -17.4593819649, $

-0.0103776001, 0.0000000000, -0.9999461513

AustinN.C.,Inc. · ‎Mar 03, 2017

This is CREO walking the tool along the retract surface, I assume a cylinder. There should be a setting in CREO where you can change the distance between points. If you increase this distance you can get rid of some or all of these moves. I don't know where that setting is but one of the CREO gurus on here should know! 😉

Fred