Community

Hi, I can't seem to install Creo 12 because when I get to the "Licenses" step, after applying the license and entering my credentials, having done this on 2 clean installs meaning I delete all of it's contents and restart the process, I am prompted with an error!" instead of a "success!" 

I am using Mathcad Release 15.0 and DatecodeM045One user trying to open a DataFiles Folder .dat file and when they click Load Data nothing happens. It will not populate the Project Name, Wall No, or any of the other project information that the .dat file contains. However, the same project file works for every other user. Even on the same existing machine. We believed this would be windows profile specific issue but we completely blew the users profile away and had them log back in to create new profile with the same results. While I understand this product is end of life, we still have certain FDOT (Florida DOT) projects that they rely on us using this until the tools this old product provide can be resolved by new versions. We are sincerely hoping you may have suggestions and options for similar issues from past that you can provide input on.Here are the errors that I facedProject Information from .dat file will simply just not load for this one user only.

I am solving a system of 1D steady ODEs in Mathcad using RK4. The system works correctly until I add a heat transfer term representing two-way coupling between a gas phase and injected droplets. When this term is included, the solver no longer outputs results and reports that the gradient matrix must be scalar or a matrix.The gas stagnation temperature gradient depends on Reynolds number, Nusselt number and a convective heat transfer coefficient that is itself a function of the ODE variables, which vary along z (length of nozzle)All other gradients (Mach, pressure, velocity, etc.) are functions of the same state vector and work correctly when the heat term is removed. I suspect I am incorrectly defining a function within the gradient matrix or using If else wrong.Any help would be appreciated, as I'm going round in circles.below is screenshot of part of code:  Thanks very much 

GreetingsI have a rather strange question, with topic that some people might consider insignificant and unimportant, but this particular function that Im making will probably be used numerous times in a single worksheet. For that reason Im trying to optimize almost every function in my file as much as possible. Ofcourse I dont expect a detailed answer with testing results etc, but rather your thoughts on this topic.In this case, I need to determine in which region of IAPWS-IF97 (formulation for thermodynamic properties of water) the point lies on a pressure-temperature plot.P-T Diagram, Validity range of IF-97So, here is the question itself: wich model of (p,T) function would be faster and easier to calculate (e.g. on a low-spec hardware), the one with separated IF`s, or the one where IF`s combined with usage of multiple "and (˄)" and "or (˅)"?And will the result be different in Mathcad Prime?Model 1Model 2Functions and constants used (for clarification, in case you are interested)ps(T

Hello all,recently bought a Creo Illustrate license and in the PTC Portal we arranged the Licensing Host details (added the name of the notebook and MAC address)The problem i have is that i am unable to start Creo Illustrate, it seems i need a file before i can start the software. Did some checks in Copilot and it mentions i need a license.dat file which i can retrieve from the PTC portal.I am able to find an option called "Retrieve license file" but according to Copilot these are not the correct file which i need. However i am not able to find another option to find this elusive file 🙂 (or is Copilot just sending me to a totally wrong non existent solution?)Thnx in advance

I am using Mathcad Prime Release 11.0 and Datecode11.0.0.0Hi Support,需要提供关于Mathcad Prime的一个功能介绍关于- 提供一个例子实现vba对Mathcad变量的读写和强制计算刷新 (组件对象模型部分)Thanks,

Version: Windchill 13.1 Use Case: I want Suggestion box under create layout of subtype of part Description: Actually while i am going to create subtype of Part Suggestion box is not coming simple Textbox is coming Suggestable class is not triggering . 

Hello Everyone,I am working with the WebFrame widget in a ThingWorx Mashup and facing an issue related to loading indication.When the URL inside the WebFrame takes time to load, there is no built-in loading indicator or event to detect the loading state. I want to display a custom loading indicator (spinner) until the URL is fully loaded.My requirements:Show a custom loader when WebFrame URL starts loadingHide the loader once the URL is completely loadedChallenges:WebFrame does not provide any loading status or onLoad eventI cannot reliably detect when the content has finished loadingAdditional Issue (Event Router):I tried using the Event Router to control a BOOLEAN variable (e.g., isLoading) for showing/hiding the loader. However, I am not sure how to properly pass or assign TRUE/FALSE values through the Event Router.Questions:Is there any way to detect WebFrame loading start/end events in ThingWorx?What is the best practice to implement a custom loading indicator for WebFrame?How can

I have already submitted the request by following the instructions provided in a previous community thread, but unfortunately PTC Korea has been unable to assist me with this matter. I would greatly appreciate direct support from the appropriate team or representative. Thank you.

HI, I'm new to CreoJS and it is the first time i meet this situation. In Feburary 2026 PTC introduced new important features for me. How can I update CreoJS without reinstalling whole Creo.    

Hello Team, I need to retrieve a list of checked-out objects and open tasks assigned to a disconnected User ( User left the org).Please give suggestions Note: I don't want to use participate admin--> select disconnect User. Thank youKumar B 

Hello, I am trying to learn Arbortext Editor, and I am trying to follow the "Get Started with Arbortext Editor" playlist. My company uses an older version (5.4), and I can't find the Arbortext XML DocBook V4.0 sample. I go to File > New and "docbook" isnt there. I can check "sample" when I highlight "free-from XML", but that file isnt the same as the one in the tutorial.  I have scoured my computer files, and I have opened every .sgm file, and I can't find it. Is there any way to get this file, or am I out of luck?

Version: Windchill 12.1 Use Case: Searching for the latest document in Windchill Desktop Integration in officeDescription: The DTI feature in MS Office, for us rarely open as a list of documents, so we use the search feature. The standard search setting is though to show all revisions of a document. This clutters the output and easily gets users to chose the non-latest revision.  Where can this preference be set?  

mathcad cannot handle correctly the swap of negative symbol in odd powers.Specific, calculating this expression (-1/8)^(-2/3) gives an imaginary result instead of the 4 as result

We are experiencing inconsistent data loss between KEPServerEX V6.13.266 and our Atlas Copco Torque Tools. Specifically, torque results are missing in the following scenarios:Power Cycles/Battery Swaps: Results fail to report immediately after switching the tool ON or swapping batteries.Intermittent Drops: We are seeing partial data transfer (e.g., only 5 out of 9 tightening cycles recorded).Please review these cases and provide your recommendations or potential fixes to resolve these synchronization issues.Kindly setup the call to discuss or need more informationThanks,MuraliKrishnan

Creo Elements Direct Modeling 20.7.1.0 (English):I can't "snap to" or "catch" an intersection when dimensioning.In this case I would like to dimension from the bottom of a key slot to the top of the shaft at the 12 o'clock position. The only way i have found is to draw a very short vertical geometry line at the point where the center line intersects the diameter line. When I create this line I can snap/catch the intersection of the center line and the diameter line WHY can't I catch the same intersection when dimensioning?Thank you for your help.Tim Higdon

Hi everyone, I’m currently learning ThingWorx and trying to connect a small IoT setup, but I’m a bit confused about the correct architecture and would really appreciate some guidance. My current setup uses an ESP8266-based NodeMCU board to read data from a wireless AC current sensor. At the moment, the ESP8266 collects the sensor data and displays it on a local web server using an HTTP client. That part is working fine. Now I want to extend this project so the device can send the sensor data to **ThingWorx for monitoring and analytics**, ideally using **MQTT** since it seems to be the common approach for IoT communication. From what I understand so far, the workflow might look something like this: Sensor → ESP8266 → MQTT → ThingWorx However, I’m unsure about a few things: Do I need to install and run a **separate MQTT broker** (for example Mosquitto) between the ESP8266 and ThingWorx?Does **ThingWorx provide its own MQTT broker**, or does it only act

 ComponentConstraint constraint = componentConstraints.get(i); Selection compRef = constraint.GetAssemblyReference(); Model model = compRef.GetSelModel(); Hello，During the development, I encountered that when the Model is an array, the assembly item model obtained from the constraint is not the correct array model. I used the above code to obtain the model according to the principle that the array parts indicated by the red arrow were obtained, but the source file indicated by the green arrow was obtained. Is there a way to get the parts of the array?

I'm using Creo 11 w/ Complete Machining Extension. I'm trying to learn 5-axis milling capabilities of Creo and I want to have a full tool library curated by someone else. I have downloaded the "Tooling Library" from PTC page "Legacy Creo Libraries".https://www.ptc.com/en/support/enablement/AdditionalCreolibraries Can anyone teach me or send me documentation on how to make use of the tools inside of Creo. For every .prt file of a tool there seems to be a corresponding .mnu file and there are 3 or 4 .exe. I imagine there is a way to view the .mnu files in a master menu with graphics, but I don't know. Thanks,Kevin

How do I get the folder ID? Right now I am trying to use the Windchill REST Services site where it generates the request and response for you. I assume that under the data administration domain you can get folders from a container using /Containers{'ContainerID'}'/Folders but it seems like none of the folders show up when I provide the ContainerID for an organization. Windchill Version 12.1.2.0 and REST API 2.5

I am using Windchill PDMLink Release 13.0 and Datecode with CPS 13.0.2.0Unable to create As Stored BOM in Windchill (Using EPM MemberLink Relaiton - InfoEngine API)Here are the errors that I facedLatest Revision of the child EPM Document shows up even when the specific revision is passed at the child level in the BOM.

Version: Windchill 13.0   Use Case: Using the + sign on multi-valued attributes with enumeration or pick list is an awful UX design. Has anyone built a data utility or interface JSP to populate using drop down checklist or a multi-select check list (like the type manager has). Description: when selecting multiple values for an attribute, there is a + (plus) sign to add another row to pick more values.   All other interfaces in the world (including type selection in the search ) us pull-down checkboxes, or pick list    has anyone already built the customization to do this that can be easily plugged in.  (Hopefully would be universal to handle any attribute)

Version: Windchill 13.0 Use Case: We are trying to use this Default Trace code in Edit Layout instead of Edit Common Attribute layout to make some Automation. and we are using listern to catch the value which check in, as this is not possible to Edit common attrbute alyout as object will not get checkout and chekcin. so i want to remove that Attribute from Edit Common attribute layout. any one know how to remove from Edit Common attribute Layout ?Description: We are trying to use this Default Trace code in Edit Layout instead of Edit Common Attribute layout to make some Automation. and we are using listern to catch the value which check in, as this is not possible to Edit common attrbute alyout as object will not get checkout and chekcin.so i want to remove that Attribute from Edit Common attribute layout. any one know how to remove from Edit Common attribute Layout ?

I have created a data utility on an attribute which opens a jsp when clicked. Now in this jsp i've created a wizard and added a wizard step. In the wizard step I have 2 table builders, so when i click on the Ok button i want to get the selected objects. But I'm unable to call a form processor on this wizard.

Hi all,I am building an automated drawing export system using Creo Toolkit (Creo 12, Windows, DLL architecture). PDF and DXF batch export are working perfectly via ProPDFExport and Pro2dExport. PLT export has been the blocker for 2+ days.What I have tried:1. ProPrintExecute — All three option getters succeed (status=0):ProPrintPrinterOptionsGet("postscript") ✅ProPrintMdlOptionsGet ✅ProPrintPlacementOptionsGet ✅But ProPrintExecute always returns -22 (PRO_TK_BAD_CONTEXT). Window ID from ProMdlWindowGet is confirmed valid (1001). Drawing is retrieved, displayed, window activated and set current before the call.2. cpbatch.exe — Cannot find it anywhere in our Creo 12 corporate installation:Parametric\bin\ — only parametric.exe and cocreatesim.exeCommon Files\x86e_win64\obj\ — not presentIs cpbatch.exe still shipped with Creo 12 or has it been removed?3. xtop.exe — Present in our installation. Has anyone used it for headless batch PLT export? What arguments does it accept?Environment:Creo Pa