Archive Read Only

Is there an easy way to cap off holes in ProE 2.0? I’m needing to do this, so I can run simulations in CFdesign. Or is there a better way of doing it? If anyone has any other helpful tips and hints it would be much appreciated.

I am trying to copy a number of components from one model to another. Is there a way to do this? The models use the same default coordinate system and are fairly similar in shape. I just need to move the components over to see if there are any issues with their placement on the other model.

Thanks - that's exactly what I was looking for. Apparently there issomething wrong with either my measure or my analysis. I get NOTCOMPUTED as the value after running a kinematic analysis, and the iconunder #3 below is grayed out. If I attempt a DYNAMIC analysis, it failsto run. "Failed to initialize dynamics analysis" I'll have to dig a little deeper.

Is there a way to change the line types pro-e creates when you save as a dwg?. Thanks in advance.

I'm in need of an ANSYS consultant for a small, proof of concept project - please inquire if you're interested or know someone that might be. Consultant must have a copy of ANSYS.Thanks,Paul DeLong

Hello, Has anyone found a good tool for translating NX data to Pro/E that maintains both geometry and mass properties? Thanks!Margi

Is it just me or is the PTC call logger on their website not working?

I've just started using CFdesign with ProE and could do with as much help as possible... I've never used CFdesign and need to master it for a Master's Project. Are there any useful ideas to think of when degsining my models in ProE (ps. using Version 2.0). Help needed... Thanks

what is crc file?

Hi,I have created FlatBody using one face and I want to fuse another face with that flatbody face How can i getthis?I have use mergewithbody option. but it is not working. it is gettingbody with two faces.

Dear ProGurus,I am creating proProgram and in the input area, i have parameter "A".However, later i would like to limit this A value to certain range which icreate using restricted range method.However, when i open the parameter box, i cannot tick the exisitng A tobecome restricted parameter.I have to go proprogram, delete parameter A, then delete A in parameter box,then recreate new parameter call A and check the restricted box.then only i am able to limit the A wihin the range value.I also notice that there are precedence depends on where we create theparameter.Any advice?THanks in advance.

Afternoon all,I am not a Mechanica user but am the admin for my site for Pro/E. One of my users is really frustrated with Mechanica not doing what he is expecting it to do. Here is his email to me, could anyone help him out with these issues? I will forward any responses to him that I recieve. Also, I will attach all the files he says would be needed to recreate the problem. If they do not come through and you think you may be able to help, let me know and I will send these files to you directly.Wildfire 3Mechanica 3Thanks in advance,Shane V.

Afternoon all,I am

Afternoon all,I

I have created a skeleton that has a merged .prt file in it. I need to replace the file with an updated version. Can anyone help?

I want to rotate several elements around a hinge point, but I cannot figure out how to specify the hinge point.What am I overlooking?Thank you,Brian S. LynnTechnical Coordinator, Product Engineering

Hallo Allerseits, ich habe die folgende Problemstellung: Es soll eine Teilmantelfläche eines Kegelstumpfes erstellt werden und die Daten über die Bogenlängen und den Verlauf der durch den Schnitt erzeugten Ellipsenbögen gemessen werden. Stellen Sie sich einen Kegel vor, der im Verhältnis Durchmesser zu Höhe von 1 zu 3 vorliegt. Der daraus resultierende Winkel zur Senkrechten ist tan Radius zur Höhe, also tan 1/6. Nun soll die Grundfläche schräg abgeschnitten werden, sodass sich eine elliptische Grundfläche ergibt und sich der Winkel der Aussenlinie von tan 1/6 auf 40° gegenüber der Senkrechten verändert. Es entsteht also ein schräg stehender Kegel, der gegenüber der horizontalen Fläche um 40° - tan 1/6 gekippt ist. Die neu elliptische Grundfläche ist nun horizontal, das bedeutet, das alle Punkte auf der Ellipse in der horizontalen Ebene liegen. Jetzt wird der Kegelstumpf erzeugt, in dem in 1/3 der ehemaligen Höhe des Kegels über der neuen elliptischen Grundfläche ein weiterer horizon

Has anyone on the forum ever created an equation driven curve to represent an NACA 5 series aerofoil profile? If so would you be prepared to share your equation?Thanks,Sam

Hi, I am trying to create a hell like those on lady shoes (stiletto heel). But I don't know how to extrude it like a cone. If somebody is able to make one and to send me a sample file with some explanation it could help...

Does anyone know if Mechanica can run combined Random and Sinusoid vibration analysis? This is also known as Gunfire Vibration environment.thanks in adavance

Hi, can someone tell me if ProE works on Vista? thanks.

Does anyone know of a good source of military connector models for download?Thanks

I thoroughly enjoyed attending this year's PTC/USER world event. Though I am still traversing the country to get home. During my lengthy layover, I have been reviewing the presentation files for sessions I didn't attend. this got me thinking.Does anyone have presentation files from previous years? I heard someone mention at the conference that last year was devoted more to best practices and standards. That is a topic I am working on at my company. Thanks in advance. Paul BockAvox Systems

Does anyone have a ProE model (or other format) of a 20' shipping container which you'd be willing to share? Otherwise, do you know of a site where I can find (free or purchase) a model?Thanks!Doug

Does anyone knows of a: Chart that shows a human adult (Male & Female) that is larger than 97 percentile or obese? 3D model of an obese person? \()/ \()/ \()/ \()/ \()/ \()/ \()/ \()/ \()/ \()/ \()/ \()/ \()/ Gary L. Stasienko Philips Medical Systems (Cleveland) Inc. Ohio USA MRI Division, Mechanical Engineering Group 595 Miner Road Cleveland, Ohio 44143, USA E-mail: -