Archive Read Only

Can I extract the only parameter value which i want in Repeat Regions instead of extracting all the values in Table......... Please show me the way out..

Installed ProE student edition on vista, the program opens fine but when i try to open a file it crashes. Wondered if anyone knows why this is.

All, I apologize, but the analysis UI changes that I described some time agoneeded to be pushed back on build in Pro/ENGINEER Wildfire 3.0. Theywill be now be submitted to M090. Thank You, Netesh GohilDirectorProduct Management, Pro/ENGINEERPTC973-753-0210 <http: www.ptc.com=" company=" tl=" index.htm=">

We are currently using WF 2 (M100) at my current place of empoyment, however, I remember using a later build on my previous contract so is there a list that recommends which versions are good versions to update to? M100 appears to have a lot of issues, how do I know what build to to update to? I don't think that they want to do the WF3 so how do I review the builds to determine which one I would like to go with or to determine which build or date codes appear to be good versions to stay with? Any suggestions?

Abbiamo ricevuto più di 150 contributi impressionanti da parte di aziende di tutto il mondo. Per votare per i vostri progetti preferiti nelle diverse categorie di prodotti, visitare http://apps.cocreate.com/descomp2007/it/index.cfm Il termine ultimo per la votazione è il 13 aprile 2007. Di seguito saranno annunciati i vincitori.

Anybody how had similar problem? I have the hole menu blinking when I load WF3 or when I assemble a new component...it takes several seconds (around 10 sec) and after it settles down. Thanks, M

Wildfire 4 is comming with Visual Basic? Somebody knows something about this? CC

Does anyone have any experience with or a recommendation for ILDP/CMF (content monitoring and filtering) software to protect data used with Windchill? Thanks, Laurie_Pelletier@Bose.com

Hi I want the weight of the model in ProEngineer Bill Of Material created by using the repeat regions.I have added the parameter(weight) in relations and i want only that perticular parameter value to be extracted in Repeat Regions.Can anybody suggest me any

This electronic message including any attachments ("Message") maycontain information that is privileged, confidential and/or exempt fromdisclosure under trade secret and other applicable law. If you are notthe intended recipient, notify the sender immediately, permanentlydelete all copies of this Message, and be aware that examination, use,dissemination, duplication or disclosure of this Message is strictlyprohibited.

What's this file and how can I get itinto proe? A supplier gave this supposed CAD file to an engineer and hewants to make a proe model.Thanks,Jeremy

Right now we are using Mastercam for CAM, but we are looking for a CAM software that integrates with ProE, so that we can eliminate file translations. I know of Pro-NC and Hypermill. Are there any other good packages available? And does anyone have any experiences with these, good or bad?

Hi users,Every once in a while the pprint will not output the desiredinformation.(Tool table etc.) Eventually it does after many tries.It did not output this morning but it did output a previouslyposted program. The program was posted last week and the pprint was fine. Is there something missing from the cldata that would cause this? The pprint was created in 1999. I am using WF 3.0040.A restart did not help.Thanks Rob Jeanjaquet

What is the difference between Flex3c and ProE_Foundation?

Dear all, can use pro/mechanical analyse ball impact for electronic product? best regards Mike Liang

Any help would be greatly appreciated! MarkN

Can anyone direct me to a sales or technical representative from PTC for Ohio DA tools? PTC purchased Ohio a few years back. Thanks, Dave

what is the difference between publish geometry and copy geometry? I tried both but both of them sees to be same. Regards Deepak

Haven't received anything from here in a long time Just checking to make sure I'm still active with it Stan KlineSenior R&D DesignerBT Fuze Products

Can anybody please help me how to set different plotting style in Proe, what is "table.pnt" file. Thanking you

Hello, Stumbled across this page of tutorials at: http://ftp2.cocreate.com/lp/lphome.html Not done them yet. So reserving comments. I am a old Pro/E user, so this is like learning to drive on the other side of the road for me... Regards.

Hey folks I have a user that needs a particular graduated color or at least needsto create it. The best way to describe it is a cross section of the sun, umber orangeon the inside and bright yellow to white on the outside. He is looking at a .tx3 file that is graduated but it's the wrong color. Does anybody have a color like this they can share or can anybody tellme how to make one? Thanks Martin T. BrownSpallation Neutron SourceVoice 865-574-4818Rm# J-319-F CLO

What is the best way to "import" a basic Illustrator outline in to Wildfire 2.0. Thanks. I know this has been asked before, I just can't remember the answer.Jim

apparently I have to kickstart the exploders.. Terry JohnsonSenior Technical SpecialistRaytheon  -- North Texas972-344-5689Save the earth. It's the only planet with chocolate by Craig PuetzNorth Texas PTC/User Group  -- President

is anyone else having problems getting mail? Terry JohnsonSenior Technical SpecialistRaytheon  -- North Texas972-344-5689Save the earth. It's the only planet with chocolate by Craig PuetzNorth Texas PTC/User Group  -- President