Skip to main content
PerForsman10-Marble
10-Marble
December 6, 2012
Solved

Wildfire 2.0 at Windows 7, 64-bit, crash when edit a drawing

  • December 6, 2012
  • 8 replies
  • 4468 views

I am running an old Wildfire 2.0 (M240) 32-bit and Intralink 3.4.

My company has invested in a new computer for me,

HP Z420 Windows 7, 64-bit with NVIDIA Quadro 2000.

After a few adjustements in two of the intralink-files, all are up and running and work just fine.

Except when i open a drawing (.drw) an try to change a dimension (right-klick and propertis).

Poff!! Pro/E has crashed.

I am not able to update in to newer software. (Company policy)

My colleague run WF 2 in Windows 7, 64-bit (Dell computer with AMD Phenom II processor and NVIDIA Quadro 600)

without problem.

Pleas help me what to do??


This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.
Best answer by SajuPhillipose

Please check the "pro_font_dir" statement on your config.pro. It could be that some of the newer fonts in Win7.0 or later is causing WF2 to crash when you try to edit. Perhaps you could change it to this:

"D:\Program Files (x86)\proeWildfire 2.0\text\" . In my laptop, WF2 is installed in "D:\Program Files (x86)\proeWildfire 2.0". These are native fonts of WF2. This worked for me.

Hope this helps.

M.P.Saju

8 replies

MartinHanak24-Ruby III
24-Ruby III
December 7, 2012

Per,

try to add the following option at the and of your config.pro to disable OPENGL graphics.

graphics win32_gdi

Then repeat your problematic action. If WF2 stays alive, then you have to play with graphics drivers - you need to find the propper version of them. If WF2 crashes then I give up ...

Do not forget to remove the option after test end.

Good luck

Martin Hanak

PerForsman10-MarbleAuthor
10-Marble
December 10, 2012

Now i have tried the graphics win32_gdi solution and WF2 still crashes.

It looks like i have to give up.

Still my question is why is WF2 running without problems on the computer of my colleague?

Per Forsman

MartinHanak24-Ruby III
24-Ruby III
December 10, 2012

Per,

do you have problems with any drawing -OR- only with one specific drawing ?

Did you test problematic drawing on second computer ?

1.] maybe your WF2 installation is corrupt

2.] maybe the drawing is corrupt

3.] may another piece of SW/HW causes the problem (for example Microsoft Intellimouse drivers can cause problems).

Martin Hanak

ptc-44377021-Visitor
1-Visitor
December 20, 2012

Maybe you can use wf2 with compatibility, running like a windows Xp 32 bits.

SajuPhillipose1-VisitorAnswer
1-Visitor
June 22, 2013

Please check the "pro_font_dir" statement on your config.pro. It could be that some of the newer fonts in Win7.0 or later is causing WF2 to crash when you try to edit. Perhaps you could change it to this:

"D:\Program Files (x86)\proeWildfire 2.0\text\" . In my laptop, WF2 is installed in "D:\Program Files (x86)\proeWildfire 2.0". These are native fonts of WF2. This worked for me.

Hope this helps.

M.P.Saju

PerForsman10-MarbleAuthor
10-Marble
September 24, 2013

Hi Saju,

I tried your suggestion and it solved the problem for me.

Thank you very mutch for the help.

Best Regards Per Forsman

Terms & ConditionsAccessibility statement