Archive Read Only

Thx for all the following answer.Everyone who sometimes concern with file transfert should not miss to hit the link proposed by Brad...David

Has anyone used Mechanical to analyze the stress in a brittle material? Such as glass, crystal, ceramic or something similar. Any problems or special considerations that I need to take into account to get accurate results?Thanks!

Hi,Does anyone ever tried to use a solid created in UG within ProE? Is there a special setup to use? In my case, few solids are well transfert, but not all of them, curves everywhere and so one...Thx in advance,David

I apologize for asking this question in a Pro-E forum, but I figure this isthe best way to get a quick response to my questions. Does any out therecurrently use AutoCAD 2006? If you could just send me an email and not tothe entire group, I have a couple of questions about manually modifying thecommand prompts you type to create line, offset, etc. Thank you.Nick

Good Morning:I'm looking for some Lego Star Wars models for use in a demo, I found a Battledroid and Yoda iges, any spacecraft or other goodies hovering around out there?May the force be with you!

fabuklous!I took the only one pijll of Cialgs and that was such a GREAT weekend!All the girls at the party were just punch-drungk with my potentiaglI have fgcked all of them THREE times but my dgck WAS able to do some more!Cgalis - it`s COOL! http://commodious.net/cs/?newsThe best weekend stuff I've ever trgied! Haven`t you tgried yet?Try IT Herehttp://commodious.net/cs/?newsm RND_DIGIT[1-3] SDcensorious converge urine avarice aaron obese brushfire dollar syntax deplore beauregard octagon downbeat someone'll othello downplay canaan would churchillian tanager basketball side angela doppler expel accession diamagnetism colicky amherst buckle u's taxi bellflower delmarva aid caracas lethargy http://www.getvisitorsquick.com/opts.html

thanks to all who replied! The basic consensus was that there is no harm in using INSERT more frequently than ALIGN, and even some definite benefits as some of you posted to the exploder. All replies are copied below... thanks!

You have to choose thru all (which is one sided).So it's kind of buried and deceptive.Then after you choose thru all go into the options tabAnd choose thru all for both directions.Hope this helpsMike

I'm trying to do a extrude cut that's 2 sided and thru all in WF2.Didn't we used to be able to do"both sides" "thru all" ?Has this been removed?It seems that only 2 sided blind is available now.ThanksMike

----------------Updated Summary

Does anyone know where the resume layer command went to in WF 2?Thanks,David LawrenceMechanical Engineer301.552.6300, X124301.577.9466 FaxSigma Space Corp4801 Forbes Blvd.Lanham, MD 20706www.sigmaspace.com

thanks for all of the responses. the following one sums up the solutionthe most lyrically.I say RIP IT...EASY SPLIT...SPLIT IT UP...GET IT STRAIGHT...GO FORIT...IT'S NOT TOO LATE...SO RIP IT...RIP IT GOOD....thanks again,bill

Does anyone remember what ERROR CODE -23 means in CAMU?Thank you,JoeJoe Haines Engineering Systems CNH America LLC500 Diller Ave MS 631 New Holland, PA 17557 - PH 717-355-3699 FX 717-355-4091

i have a newbie question. how can a hollow cone be flattened? i'mgetting the "helpful" inappropriate edge message. any help would beappreciated.bill505-845-9666

Thanks for all the responses. By using a couple of new icons (and maybe and a few new mapkeys), WF has the same functionality as 2001. Here's my original question and all responses:

Hi Everyone,I really need some help here. I've been contemplating buying a laptop towork on ProE.And as it turns out I am absolutely confused. I have brought it down tothree options keeping usability ruggedness and serviceability in mind.1) Toshiba Satellite M50 or Tecra S2 (http://www.hclnotebooks.com/product.htm#<http: www.hclnotebooks.com=" product.htm="> )2) IBM T43 or T42 (http://www-604.ibm.com/webapp/wcs/stores/servlet/ProductDisplay?catalogId=-356&productId=33068044&storeId=10000356&langId=356&dualCurrId=1000105&categoryId=2060442<http: www-604.ibm.com=" webapp=" wcs=" stores=" servlet=" productdisplay?catalogid="-<br"/>356&productId=33068044&storeId=10000356&langId=356&dualCurrId=1000105&categoryId=2060442> )3) HP 8230 (http://h50025.www5.hp.com/hpcom/in_en/11_28_366_3957_PY746PA.html )Any suggestions or advice would be a big big help to me !Thanks.Aditya

I want to send a big thank you to Joe, Doug, Herb, Michael, Ben, David andBen for the color maps. This exploder always amazes me with the quick andhelpful responses! I will send what I have to the few that requested infosoon. Thanks again guys!Nick

Pro-SuperUsers,We just upgraded to Wildfire 2.0 from 2001, and we got a very basic colorpalette. Does anyone have a good color palette that they could send me?Thanks.Nick

A big Thank You to Steve Jones for reminding me that I need to take ALLthe spaces out of the file name and not all but one...e SPINE / NON-FUSIONJustin GiaquintoDraftsman/CAD Operator Tel: (610)719-5703 Fax: (610)719-5100 -

How do I control the layers of a component during the placement process??

I'm guessing that Marty is doing software QC for PTC. Why do I say so? Because of the number of times a requester/menu pops up a long distanceacross the screen from where the pointer was when I clicked the mousebutton. Mr. Feldman could have kept up with most of it, but I'm adon't liketo. I know that this occurs sometimes to prevent blocking the next pick,although... The best example today is Edit/References/Replace Ref. The Edit menu is upper left. The References selection is mid to lower left. The menu that appears is in the Upper Right, but the question it stops toask is in the screen lower left.The box to click Yes/No is at the lower right. All corners covered. All that's missing is a decent pop-under modal requester (1 pixel X 1 pixel,please ) and it would be complete. A chameleon could not watch all this at the same time, so I guess that thesoftware QC guys are more flexible than them - obviously more flexible thanme. I know, I know - create a mapkey to skip the whole thing.

Who has an involute gear as a UDF that follows the standard ANSI spline geometry. Found the http://www.ptc.com/cs/cs_25/howto/agf652/agf652.htm. But I never could get a UDF to work for inside or outside gear teeth. Best Regards,Mit freundlichen Grüßen,Saludos, Mitchell SmithProduct/Prototype DesignerZF Sachs Automotive of America15811 Centennial Dr., Northville, MI 48167Phone: 734.582.8062 Fax: 734.459.6491Main phone: 734.416.6200Mitchell.Smith@zf.com <blocked::mailto:mitchell.smith@zf.com>

Does anyone know of any publication that reviews any or all of the geom_checks and explains them?Dan SchurrCAD FacilitatorEATON Corporation13100 E. Michigan Ave.Galesburg, MI 49053tel: 269-342-3236fax: 269-746-6236-

Proe users,I need some help in creating a drill file.I'm using Proe2001.Brad

Did this ever get fixed in a WF2 build that anyone knows of?I'm using M080 and the icon seems to map to an old menu location.ThanksMike Singer