Archive Read Only

Hello, Is Pro/ Plastic Advisor included with Wildfire 4 or do you have to buy it sepparetly? thanks, bern

Can anyoneshow me a way(if it is possible) to have the weight (mass) of a Simp Rep caluclated and have it in a table on the dwg. like we can do with the &WEIGHT:1[.0] for the master rep.thank for any helpMike Forrette-

Like many of you I have spent years cleaning up Pro-E items. The eternal quest to eliminate such things as Circular Refs and Ghost Objects. Now the bean counters ask me: Why spend the time doing all that extra work? We can still release the parts so why can’t we just leave them alone? Can you give me your answers to these questions? How bad are these items? What is their impact to component cost? What happens if you just leave them alone?Curtis Odom

Hi,Is there any way in Pro/Tookit to identify weak dimensions in a section?I am going through documentation and found nothing useful so far.Thanks,Regards,Amar

Hello Nuno, There are also trainings and tutorials on TDO available in PTC.com, however I strongly recomend that you check out PTC University. There you can find courses that may help you with all of PTC products. ________________________ Agora em PT Olá Nuno, Existem disponíveis tutoriais sobre o TDO e EMX disponiveis no site da PTC, no entanto, recomendo vivamente uma visita à PTC University. É basicamente uma Universidade online com cursos acerca de todos os produtos PTC.

Dear All, If anybody having Pro-Tool kit auxiliary for any application pleaseforward me.Thanks in advance. With best regardsGopinath

Dear All, If anybody having Pro-Tool kit auxiliary for any application pleaseforward me.Thanks in advance. With best regardsGopinath

Dear All, If anybody having Pro-Tool kit auxiliary for any application pleaseforward me.Thanks in advance. With best regardsGopinath

Hallo in die Runde, ich habe mir gerade CoCreating Moddeling Personal Edition heruntergeladen, doch beim ersten Start des Programmes kommt die meldung, OLAPE hat ein Problem festgestellt, un muss beendet werden. Dannach kommt die MEldung, ich hätte keinegültige Lizenz! Kann mir jemand weiterhelfen, oder habe ich einfach etwas vergessen, oder nicht beachtet? Danke im Vorraus für die Hilfe! Gruß Tristan

I am attempting to create a curvature continuous style curve that closely follows and references two arcs. Essentially, the new style curve will run through the arcs and provide a transition between them. I'm having trouble with the final result as it has unwanted inflections. Both arcs are convex and I essentially want a curvature continuous radius between them. Any suggestions?

Can someone stop this foxy advertisement? I get this e-mail everyday...Do you read this e-mail, Mr. Kellner? What are you trying to do? This isreally rude and immoral...Kind Regards,Murat TOKLU "Paul Kellner" <consult1@engtran <br="/> .com> To Sent by: - consult1@engtran. cc com Subject [proecad] - RE: List Digest, Nov 13.11.2008 11:06 12, 2008 Please respond to "Paul Kellner" <consult1@engtran <br="/> .com> Thank you for contacting Engineering Transport.

Thank you for contacting Engineering Transport.

I am trying to use the PTCViewer control in an asp.net page, but am running into a persistent problem. The page loads fine, and the control renders the image correctly -- but when I close the page, it seems to "hang" the browser until I manually end the task. There is nothing else going on with the page (no load/unload events, no other controls, etc.). It happens every time with both IE6 and IE7. Any suggestions would be greatly appreciated. Thanks.

I'm curious about how Mechanica treats a load distributed on a beam. I have a beam-based trailer frame I'm analyzing, and I came up with someunexpected results (see the attached picture). I was not expecting the stress in the center beam to be so much lower thanthe of the frame - in fact, I was expecting it to be higher. Closerinspection of the results show a stress of under 500 psi in this beam. IKNOW that aint' right. I'm going to re-run the analysis, substituting the one distributed load withmany smaller point loads, but in the meantime, can anyone tell me why thisis behaving this way? It seems like Mechanica is making an assumption I'mnot aware of. -- Lyle BeidlerMGS Inc178 Muddy Creek Church RdDenver PA 17517717-336-7528 Fax 717-336-0514 <">mailto:-> - <">http://www.mgsincorporated.com>

Thank you for contacting Engineering Transport.

Hello,It's Maintenance time and this year, I get to be involved.  I'm looking at what we own vs. the available packages (Foundation, Advanced and Enterprise) to make sure we aren't paying for more or less than we need.  The PTC web site gives a general overview of what's in each package, but it's not specific, that I've found.  Is there a document that shows what specific modules (Pro|Assy, Pro|Detail, Pro|Report, etc) are included in each package?  That would be very helpful.Thanks,Doug Schaefer

I am looking to implement some standards into hole features using WF4, in this case blind holes. I would like to specify the thread length for blind holes and have a relation (or something) that adds a fixed value to determine the correct drill depth. I do not see how to do this by customizing the .hol files, but I am hoping there is a way.IE for 1/4-20 UNC drill_depth=tap depth+.2505/16-18UNC drill_depth=tap_depth+.278etc.This will then drive pro/manufacture later in the process. Please advise what others are doing to make this work as robust as possible.Thanks,Bill ChapmanSencon

Any suggestions on the best places to post a job advertin theUK without having to go through agencies?Cheers, SeanLoughborough University

Any suggestions on the best places to post a job advertin theUK without having to go through agencies?Cheers, SeanLoughborough University

Thank you for contacting Engineering Transport.

I'm running Pro/e (3.0) I have the box checked to highlight preselected objects, however when I move my mouse cursor over an object it does not show up in red like it should. In the model tree I select highlight geometry and preselection highlighting and it will underline the component or operation, but that's it. I could not figure out how to get this back to default and work like it normally should. Please help me.[/code]

Does anyone have a hole table for standard flat head rivets used in the aircraft industry?

I was told that only keys that display characters when typed can be usedfor mapkeys. Thanks,Matt

Thank you for contacting Engineering Transport.

Can any body Please provide List of Pro/E Users ( Customers) Across world.ThanksSrini