Archive Read Only

I'm sorry if you received this the first time I sent the request but since I didn't get any out of office reply's or an answer I'm guessing that no one got the original request. Is there a way to change the Text height and or the Type of text used in theModel Tree?WildFire 2 - M190Curtis SmithAida America

I did a search and it said to use File/Open change file type to .jt, however I do not see the option to select .jt. Anyone know if there is another way to do this.

Hi,Is anyone using this simulating program by means of Pro/Engineer parts?How does it work without the Pro/ENG Import Module suggested by COMSOL?How is the interactivity?Thanks for the advice!

Halllo ich bin noch etwas unerfahren in Cocreate PE. Wenn ich versuche ein Teil als VRML-Datei abzuspeichern, ist das Auswahlfenster leer. Bei Auswahl ""alle Objekte"" erscheint ""Einzelauswahl erforderlich"". Woran kann das liegen? Für schnelle Antwort dankbar MONIPOS

Any one know where I can get free 3d drill bits? Iges etc.?

Has anyone ever had troubles with RP houses saying the edge radii in STL files look gouged and not smooth?The chord height has beenadjusted to the input defaults, and angle control I've never been asked to change.This problem seems to have appeared in WF3 and WF4.

There are a lot of thicken options. None of these option allow me to do what I thought was possible inearlier versions. Thicken a thin Solid Thanks to those who replied. replies :

Hi - I'm throwing out a question from that all too familiar place of ignorance...Where does one start when tasked with setting up bi-directional workflows between Agile 9.2.2.4 and IL8 M045? Is this a consultant thing, or are their modules that need to be purchased?Would like to have Agile see revision and release level changes in IL, and IL see changes initiated in Agile.Thanks in advance - will post relevant replies.-TerTerrence (Terry) McFallCAD Systems AdministratorVarian Medical Systems911 Hansen WayPalo Alto, CA 94304650-424-6039 desk650-799-0179 cell

I know that I'm NOT too young for the Senior moment plus I ate all thatbeef in the eighties so my brain must look like a sponge. Some days Ihave to be reminded to wear trousers so I guess forgetting a Proe menucallout is small fry! John's advice worked perfectly and I've written it down, now if only Ican remember where I put it.......... Thanks, Richard A. BlackLead EngineerEaton Corporation16900 Aberdeen RoadLaurinburg, NC. 28353Tel: 910-610-1788Fax: 910-277-3700

I'm using WF3 drafting mode and am having a senior moment. I have erasedthe title to a section view (e.g. SECTION A-A). How do I get it to"show" again? Richard A. BlackLead EngineerEaton Corporation16900 Aberdeen RoadLaurinburg, NC. 28353Tel: 910-610-1788Fax: 910-277-3700

Since the last time I brought this subject up, I have been contacted by users wanting to know how to make these parts. A few months ago I had an opportunity to experiment one more time. What you’ll find at the other end of this link, <u>http://www.box.net/shared/ahhcczagcg</u>, are the results of that work. If you are interested, enjoy. Just reply to this thread with a simple thank you. Anyone who has ANY negative comments, just remember what your mother used to say, “If you have nothing good to say, don’t say anything at all.” Now, if you excuse me, I have a boat to catch…

How do you open files created by Pro Engineer 3 in Pro Engineer 2 ? Is it even possible?

Is there a way to change the Text height and or the Type of text used in theModel Tree?WildFire 2 - M190Curtis SmithAida America

I recently upgraded to Wildfire 4.0 from Wildfire 3.0. I had the software setup to launch full screen, but now it fills the screen width wise but there is a 1/2 of the monitor not filled on the bottom. What can I do about that?

Does anyone knows how to change the zoom factor in Pro/Engineer so that I can control how fast to zoom in and out when rotating the mouse wheel?Thanks.

In detailing iam unble to create partial view in a unfolded view. is it not possible in proe? is there any solution for this?

HI ALL, please let me know how to download example files for PTC. Eg.- http://www.ptc.com/cs/cs_24/howto/agf362/agf362.htm THANKS. HARI..

It's been a while since I did any NC work. Can someone tell me how toswitch the direction of my cut? Currently it is from upper-right tolower-left. I want it to go from lower-left to upper right.ThanxTony

It probably is right in front of my face, but I don't see itWhere did section thicken go ? I'm on wildfire 3.0 M110

Is there a way to hide dimensions and constraints while working in the sketcher?

hi friends i need round options about 1.normal to spline 2.detail dialog box 3.transition (stage-1&stage-2)

Ist es normal das wenn ich zum beispiel ein Rechteck erhöhen will und auf die schaltfläche gehe das ich dann nichts mehr im Editor erkenne und sich alles verzehrt? sobald ich auf das rechte kreuz klicke oder zoome verwindet es. Aber sobald ich wieder editieren will verzehrt sich alles. HILFE

Just curious if anyone out there has a model of a standing person that they would like to share? Thanks,James Westerfield | www.benchmade.com

Can someone please explain what the purpose of the Front & Back referencesare for a cam follower connection? My colleague is having some trouble withit, and the help files aren't much use. -- Lyle BeidlerMGS Inc178 Muddy Creek Church RdDenver PA 17517717-336-7528 Fax 717-336-0514 <">mailto:-> - <">http://www.mgsincorporated.com>

Registration for the PTC/User program at RCR NASCAR Racing Shops next week(Wed Oct 1) is still open. There is no charge for Users (your breakfast and lunch are provided by oursponsors), but you gotta sign up. . Come see new features in Wildfire 4 and a sneak preview ofWildfire 5!. Hear your favorite presenters talk about Pro/E functionality.. Register for a Mindstorm NXT and other cool items. More info at