Archive Read Only

Hello Pro/M gurus! Can anyone help me verify the results of my Pro/M modal analysis on the following: Cantilever beam 12.0 inches long, width is 2.0 in, height (or thickness) is 0.5 in. Properties are: Young's modulus = 30,000,000 psi Poisson's ratio = 0.30 Mass density = 7.22e-4 lbm/cu. in. The above modal setup was an example from the book: Building Better Products with Finite Element Analysis by V. Adams and A. Askenazi. (see page 478). The result given in the book for the first natural frequency is 114.5 Hz (using formula).The result given as obtained from MSC/NASTRAN is 114.0 HZ. The result that I got from Pro/M for the first mode is 2243 to 2264 Hz (I tried the analysis on the idealized model and the solid model. Convergence was to within 1%). Need your help to verify if I made a mistake in my setup. I am using Pro/M 2001. Thanks for all your help in advance. Jerome Simbajon

Need a cad model of an Army helmet. Rough approximation is OK. Just need it for pictures.Anyone have one to share or know where to get one?Also.... I could use an Army backpack as well. ThanksErik

Well seeings how everything is a little differnt I am not shocked to findout that making a singular word BOLD in a line of text has changed.Does anyone know how to do this ?I noticed that braces are no longer required {}

-----Original Message-----Did/does anyone else have a problem with the mouse wheel not zooming inWildfire 2.0 release M040?Thanks in advance,----------------------------------------------------Thanks for all the replies. I had forgotten to mention some things like Win 2000 and the wheel worked fine in Wildfire 1. Doing a simple "Update Driver" on my mouse worked, (You might want to try that Daryle).For archive's sake, some other people's solutions to same problem:A mouse setting for the wheel set to 'auto scroll'.Mouse in USB port not working, use adaptor into round mouse port.

Ronald Grabau just wanted to say thanks for the great article in this month's Profiles.If you people haven't seen it, check it out.http://www.profilesmagazine.com/p30/grabau.htmlBrian S. LynnCAD Administrator/Designer

Hello all:Does anyone have or am I missing within Pro/e the symbol for 3rd angleprojection?Thanks,-----Andy Henry ( andy@tcservice.com )T.C. Service Co. - Top Cat Air Toolshttp://www.tcservice.comVoice 800 321 6876 or 440 954 7500Cell 440 339 7359

I am trying to gather information on Pro/e system management courses. DoesPTC offer these and how do I get enrolled?

Associates, Does anyone know if it is possible to change the number of recently opened files displayed at the bottom of the "file" menu? I have a user that wants to display a longer list to make retrieval easier. If anyone knows how, please let me know. Thanks.Dave

Do you guys have any simple 3D exams to test blueprint reading ability?IE: given an isometric view ad then you need to either match or generatefront, right, top, etc.? I have also seen tests where they have stacks ofblocks shown isometrically that you need to count.Thanks,1st

Here are all the responses I received followed by the originalquestion...thanks again to everyone!

Thanks to Brian Lynn who pointed out that the coordinate system creation for a coordinate system is located under the point button in sketcher. I am now able to get a toroidal bend but I can only specify the angle of the bend. What I want is to be able to specify the bend radius and have the bend angle determined by the system.> Dwayne Quatier> GE Healthcare> Ultrasound> Product Development Engineer> T 480-222-7003> F 480-760-2489> E -> www.gehealthcare.com> 365 S. 52nd St> Tempe, AZ, 85281, USA>

Thank You all.Found some sites I didn't know about.I used SDP's nice models Here were the links:www.sdp-si.com <http: www.sdp-si.com="/>

Hi all -- Can the model tree be detached from its anchor in WF2? Can't find it in customize menus.Thanks.ChrisChris RockholdSr. Tech Support Engineer II978.440.2706978.440.3322 fax-

Pro-Users,I am trying to create a balseal rotary seal and the spring contained withinthe seal is a "rotary" spring with the spring coils revolving around asingle diameter. I know how to make a standard helical swept spring, but Iam not sure how to attack this one. Any help would be appreciated. Thanks.Nick

Wondering if anyone had a model for the Tinnerman Palnut. The trimclip, p/n D98810-051M. Thanks in advance!

Did/does anyone else have a problem with the mouse wheel not zooming inWildfire 2.0 release M040?Thanks in advance,Joe

Greetings All Could any of you guide me to the PTC's web site concerning pc hardware,certify specifications for W/F 2.0Thank you

Where do you specify the cross-section's default font(global setting). I've spent some time reading PTC'sknowledge base database with no luck.Thanks

The answer is..... SETTING FILTER IN LOWER RIGHT CORNER before editting properties.THANKS AGAIN! -Liisa

hopefully another easy one...how the heck to I modify a GTOL I already created?Liisa

Is there a way to flag shown dimensions that loose references?, instead ofthem dissapearing when the refernces dissapear. Similar to the way createddimensions turn magenta when their references dissapear.We have been using created dimensions to get around this issue, but ratherjust use shown dimensions.Thanks!

Hi!We have a new product that we offer to you, C_I_A_L_I_S soft tabs,Cialis Soft Tabs is the new impotence treatment drug that everyone is talking about. Soft Tabs acts up to 36 hours, compare this to only two or three hours of Viagra action! The active ingredient is Tadalafil, same as in brand Cialis.Simply disolve half a pill under your tongue, 10 min before sex, for the best erections you've ever had!Soft Tabs also have less sidebacks (you can drive or mix alcohol drinks with them).You can get it at: http://labgikdejm.upromeds.info/?cfhdejmxtnqylzctabgik benoit rufuspetunia bobcat easter nick cuddlesrepublic lucas fountain rock megan eclipse research racerx basil xxxx mortimerrock mars mimiseptembe septembe gambit niki sashagretchen prof nauticarobinhoo fletchjosie playboy wanker rambo1 jared rux

I imported a DXF file of commercial item from vendor siteI tried to cross-section to look at interiorI cant see cross section - does this not work with DXF?(running 2001)Thanks

GlacierDear Proe GurusPlease suggest Involute spline procedure for gearcuttingRegardsE.DevarajanProduct DevelopmentRane TRW Steering System LtdPump DivisionPh : 04114-265010/265236 Ext : 210Mail Id : e.devarajan@rane.co.in