Archive Read Only

Does anyone have these agency symbols created as a sketch, and would they be willing to share them?I can't even find a picture of them on the web.Best regards, - Phillip M. Kukelhan Mechanical Designer Eaton Power Quality Corporation 3201 Spring Forest Road Raleigh NC 27616

Thanks everyone for your replies.After about 30min. of trial and error I gave up.And so did everyone else that replied, here are the replies I got.

SUMMARY:PTC says that the ovals conform to DIN 406-10 but doesn't explain further. DIN 406-10, section 3.2.6.1, explains that an oval "frame" identifies "check dimensions," which are characterized as "requiring particular consideration when the scope or stringency of inspection is specified."I read that to mean that you can use the oval frames to designate dims for some type of inspection--first article, ongoing, whatever--but that you must define the type of inspection. We'll probably stick with a note like "Dimensions within an oval frame shall be used for First Article Inspection."Thanks, Rick, for pointing me to the DIN standard.- WallaceRi

Thanks to Brian, Doug and Vaughn!!! ITOS - Integer to StringFloor- Round down to integer And my relation should read something like:deg_A = itos(floor(A)) exact_min_A = (A - floor(A)) * 60min_A = itos(floor(exact_min_A)) exact_sec_A = (exact_min_A - floor(exact_min_A)) * 60sec_A = itos(floor(exact_sec_A)) ang_val_A = deg_A + "° " + min_A + " " + sec_A + "" Thanks again!Justin

Another tidbit, there are no repeat regions in the table frozen table. I'm going to replace the table but it would be nice to know a better workaround if one exists.--ChrisChris Rockhold <->Sent by: -01/25/2005 08:50 AMPlease respond to Chris Rockhold

Just in case anyone else is looking into it and could use the advice:Original Message:Subject: [model] ProductViewMaybe a bit off topic, but do you use ProductView in your organisation? If so, what do you use it for and how do you use it? What problems have you encountered and what have been the high points? Any advice for a new prospective user? We are thinking of starting to use it for a variety of visualisation requirements (of Pro/E data) and it would be nice to get a leg-up on the learning curve. Thanks, and have a nice weekend.

I am unable to modify a table. The dialogue is "you may not perform this action on a frozen table". WF2. How does one un-freeze the table?Chris RockholdSr. Tech Support Engineer II978.440.2706978.440.3322 fax-

Hello experts,Can you suggest some way to have a parametrically scaled model? I have a model which is to be enlarged by some scale factor and this scale factor should remain parametric so that i can change this scale later with one parameter. Is there any way to do this? Please help!ThankYou.-Anurag

Hello all,Does anyone use the .psf file to launch Wildfire2? In 2001 we use the ptc_startup.bat file to set some environment variable, copy configs, remove and/or copy other files to the users workstation when they launch ProE. Is this possible in the psf file? I also noticed that the psf file is located in the bin directory. When you launch the ptcsetup.bat file doesn't it over write the psf file? How can you keep the psf file custom to what you want it to do and not create the possibility of over writing the file when the user does a ptcsetup?Thanks In Advanced!!JHengel

Hi!to all pro gurus. Anybody around there have nylon material that want to share ?I'm using pro/e 2001 I will appreciate Thank You! Federico PerezCad OperatorTPG Inc.

Maybe a bit off topic, but do you use ProductView in your organisation?If so, what do you use it for and how do you use it?What problems have you encountered and what have been the high points?Any advice for a new prospective user?We are thinking of starting to use it for a variety of visualisation requirements (of Pro/E data) and it would be nice to get a leg-up on the learning curve.Thanks, and have a nice weekend.

Folks I have received over 50 requests for the humvee model and more eachday! I would like to have the time to respond to all these requests butsomeone in my IT is going to come down on me if I send out any more. Itsencroaching on our bandwidth at 2meg a pop. I will try to find a place toupload them and get back. I appreciate your requests. Maybe there shouldbe a place on this exploder to post models??? I had no idea so many peoplework on Humvees! This model is not for someone designing hardware to otherthan rough external geometry. Maybe one of you I sent it too can post youhave it for now. Thanks!Gerald

Does anyone have a model of an Evo engine that they wouldn't mind sharing?ThanksThis e-mail message may contain confidential or privileged information. Ifyou are not the intended recipient, please delete the message and anyattachments and notify the sender by return e-mail. You should not retain,distribute, disclose, or use any of the information in this message.

While everyone is asking, Hey I need a model of our complete project does anyone know where I can get one?????

We have the need to import excel files as tables in pro/e, and be ableto modify them in pro/e. It would be nice to be able to also change inexcel too, but not a requirement. We are in version 2001, and will bemigrating to WF2 in 2-3 months. Does Wildfire 2 take care of this or isthere 3rd party software which would meet our requirements better.Thanks.Eric FlemingEngineering Technician2881 East Bayard StreetSeneca Falls, NY 13148Phone: 315-568-4543Fax: 315-568-4507-

Hello Admin'sIs there a way we can change the duration of the splash screen. I changeours all the time with new images of our latest products and the companyname. I would like to give the splash screen about 5 more seconds beforeit launches into Pro/E. I plan on making this splash screen a Flash NewsReport for the users.What do you guys think?Damián CastilloMCAD AdministratorPro Engineer ConsultantHensley Industries972-406-4788

PRO USERS,

Thanks guys, that helped a lot... except the 45 million 'out of office'replies I got - man, I love Microsoft Outlook, its so cool.

Would anyone have a model or models of floating nut plates that I coulddownload? Or can you point me to a location where I can download some?I have checked with Pro/E Stuff and Pro/E central. I also have check, butnot yet contacted the manufacturer for requested nutplates. I will postthe results of my search.TIA

You guys are the best...

Good show JPL!http://www.esa.int/esaCP/SEMQ1QQ3K3E_index_0.html

A woman was shopping at her local supermarket where she selected Ahalf-gallon of 2% milk, a carton of eggs, a quart of orange juice, ahead of romaine lettuce, a 2 lb. can of coffee, and a 1 lb. package of bacon.As she was unloading her items on the conveyor belt to check out, a drunkstanding behind her watched as she placed the items in front of thecashier. While the cashier was ringing up her purchases, the drunk calmlystated,"You must be single."The woman was a bit startled by this proclamation, but she was intriguedby the derelict's intuition, since she was indeed single. She looked ather six items on the belt and saw nothing particularly unusual about herselections that could have tipped off the drunk to her marital status.Curiosity getting the better of her, she said "Well, you know what, you'reabsolutely correct. But how on earth did you know that?"The drunk replied, "Cause you're ugly".