Creo Modeling Questions

how to create new material? any boudy give me material specificatin sheet or material file. so i will creat or add material in my library, how to create new material? any boudy give me material specificatin sheet or material file. so i will creat or add material in my library

long time back there was wonderful software going by the name of Pro/Engineer for 3D modelling.what happened to it?it was powerful,it was logical,had lots of capabilities,when ever you thought this could not be done in Pro/E..there was the functionality.then every body started copying it...Solidworks,Inventor,Solid Edge...yes all of them...and now they say that these copied software's are better......yes surely...u just had to copy the main functionality and then tweak it..and say we are better..so original right.never mind....what i do mind is...Pro/E copying user interface...of these copied softwares..instead of building on there own functionality.why have you lost your confidence....PTC?

Allow an Annotation to be related to another annotation/weldnote.Isn't this done by selecting Offset instead of picking a placement?

I could write a SolidWorks add-in to do this in about a minute, but I don't know the Creo API yet. Does anyone know if there is an option to do this or an existing add-in? I didn't mind the Window menu from Wildfire, but the tiny icon in Creo is inconvenient.Thanks

Can anyone tell please?

I have a table that I have been using that has "&todays_date" which has been working well and shows the date as 10-MAR-15.I copied this table over to another table, but similar and when I go to use this new table with "&todays_date" it works also, but shows the date as Mar-10-15.How do I fixed the format of the date when they are both "&todays_date"Thanks, Dale

Is there any option available in Creo, which will Automatically adjust Table Width size according to text length.?

does anyone know if there is a limit to the amount of mapkeys you can have? I dont seem to be able to create any more than 83 which seems like an odd limit

The following meshing of a 2D plane wanted.But I get the following meshing.The points marked are inserted automatically by software. AutoGEM Control "Edge Distribution"used to control .Any one have any idea how to improve it?

I need to make a moving model of my robot and for that i need force motors, dynamic motion, gravity, friction, etc. So any help would be but welcome.

When I open *.x_t file in the Creo 2 I received solid model.When I open the same *.x_t file in the Creo 3 I received faced model.How need change setting in Creo 3 to receive solid model after opening *.x_t file?

I have downloaded 30 days of trial version of creo 3.0 on my laptop but I cannot find 'setup' folder or neither of 'parametric.exe'.Anybody can help me out to set up or run this trial version properly?Thanks.

What does the TBD mean next to red, green, and yellow regen status lights ? (see attached jpg)

This is in my flat state simp rep or in any combination state for that matter. Any ideas on what may be the issue? They show up as suppressed in the detail tree. Creo Parametric 2.0 M120.

I need to work on one of my models urgently!So Please!

PTC should restart it support for Linux for Creo.

sir , my name is kashyap and I am getting problem while entering the code in it ... the box where I supposed to enter the code is not working . and the curser on the box is totally fail to work on in the box.

Short question:Is there any way to make Creo run a mapkey when opening a file?

I have created a channel using boundary blend command. For this purpose I used two longitudinal curves and seven sections as shown bellow. The starting section is circle and the last one is almost rectangular.When I use boundary blend command to create channel, lots of lines were appeared on the quilt( see figure bellow). Does anyone know how I can remove them?

OK, I'm using this thing a lot today.Does anyone know if it is possible to get the area of a Cross Section fromPro/E?Thanks,Erik Olsen

Hallo zusammen,in der neuen Forumsumgebung tue ich mich erstaunlich schwer.a) finde ich den Zugang zum deutsche Forum sehr kompliziertb) finde ich keinen Schalter eine Antwort als "richtig" bzw. "hilfreich" zu markierenc) finde ich den Zugang zu den Katalogen nicht, in der Teilnehmer ihre Erzeugnisse präsentieren.Ich glaube umständlicher ging es wohl kaum oder?Gruß Werner

Hallo zusammen,im augenblick habe ich irgendwie ein Brett vr dem Kopf.Selbst die beigelegte Onlinehilfe gibt mir keinen Aufschluß.Ich habe mehrere 3D-Kurven (Geraden und Bögen), die ich zu einer Flächeformen möchte.Ich schaffe es nicht eine Verbindungslinie zwischen den auf verschiedenen Ebenenliegenden 3D-Kurven aufzubauen, geschweige eine Fläche zu erzeugen.Ich bevorzuge Express 4.0, kann aber auch mit Express 6.0 arbeiten.Zum Verständniß lege ich 2 Bilddateien und die Expressdatei bei.Mit Gruß Werner

Damián CastilloCAD & Administration ManagerEngineering DepartmentHensley Industries, Inc.

Anyone using peck tables? If so would you be willing to share and example?Thanks in advance.