CAD

I am using Expert Moldbase Extension Release 14.0 and Datecode14.0.0.0Unable to open Creo with EMX extension. I get the following error messages:"Creo Agent did not initialize correctly. Please contact Technical Support if the issue persists."And:"Unable to start application 'EMX' due to failure in starting Creo Platform Agent."Here are the errors that I faced"Creo Agent did not initialize correctly. Please contact Technical Support if the issue persists.""Unable to start application 'EMX' due to failure in starting Creo Platform Agent."

Hello All, I'm trying to extract data from 2 variables. Example, by selecting Material data from drop down list and temperature. It should throw allowable stress value.For P11 material at 1050degF, allowable stress value is 4200psi.  Can you please help me on this problem.  

I am using Creo Schematics Release 7.0 and Datecode7.0.0.0All of the icons in all of the toolbars in Creo Schematics are hard to see, they have no color and blend into background. I can fix this by turning off the "Dark Mode" in WIndows 10, however I like the dark mode when using all other programs and windows. I would like to keep dark mode on and still be able to see the toolbar icons in Creo Schematics. I have looked in the "Options" section in Creo Schemtics to see if I could tell it to ignore the system color/theme but I didn't see any such option. Can this issue be fixed?

HiI have the following relatively minor problem with Chart Component axis. If I let Mathcad to select axis values automatically, the maximum value doesn't show in the graph at all. If I set the maximum value of the y-axis to be 10% higher than the largest y-value, the axis values are no integers, but have decimal values as well. Is there some way to set axis values automatically, in a way that the maximum value would be shown in the graph, but also the numerical values in the y axis would be integers? In the attached sheet, there are three graphs. The first shows how the graph is shown automatically, in the second graph maximum value to y-axis is set, but as noted the y-axis values are not integers. The third graph shows how I would like the graph to look like, but I would hope that Mathcad would produce this kind of graph automatically without manual selections.  

I have this same issue. My computer died, I followed the links https://support.ptc.com/appserver/auth/it/esd/academicFree.jsp & https://www.ptc.com/en/success-paths/upgrade-your-creo-parametric/setup/download-and-install-creo and went through the installation on my new computer. However, during installation it gave me an error when I put in my SON. I went through the installation without licensing and put the license file in the PTC folder like this: c:\ptc\license.dat. After launching creo I get a license error. I think because I have a node locked license. But service won't help at all because I dont a have maintenance subscription. I paid for a permanent license so I feel like this is some sort of illegal loophole they have going. I'm assuming I need them to release the license from my dead computer so I can activate it on my new computer. Any ideas? I downloaded my license again from my PTC login but still no luck.

I need to get data out of an MCD file. PTC MathCad Express Prime 8 cannot open MCD files, so I was trying to convert it into an MCDX file first. When I try to use the "XMCD, MCD Converter", I get an error saying "Unexpected error encountered during conversion". How do I resolve this?

Need to algebraically solve for a variable in prime In legacy MCAD it was symbolics,/ variable / solve where you highlight to desired variable In prime I see Math / Symbolics / Solve But this does not work as legacy MCADIs this possible in PRIME    

Hola,since PTC offer Home user Creo license program for personal use I am curious why doesn't support Windows Home editions as well? There is official support for Windows Pro or Entrerprise only but many users have installed Win Home on personal computers. Anyone tested Win 10 Home with Creo?My experience with Creo 6.0 on Windows 10 Home is one big fail so users with Home Win edition are probably disqualified...

I am using Creo Parametric Release 6.0 and Datecode6.0.4.0We have a business configuration and Winchill as PLM (PDM). In our configuration we point to our libraries (our libraries are on windchill). We have, for example, libraries for our drawing template. But when I create a new drawing care don't reach the libraries we ask in the configuration, we reach the standard PTC libraries.This issue starts one day with no explication, I'm the only user who has this issue and we tried some re-install and install on an other computer but nothing change.

Creo View is displaying a narrow font when viewing a drawing that was exported as CGM format.The native dwg from Creo Parametric and Catia displays the font correctly before exporting as CGM. Is there a setting in Creo View that converts or shows the correct/native font when viewing the drawing?   

Hello, What would be the best way to get the inheritance part number into a drawing.  I am using creo with windchill My scenario is that i would like to be able to refer to this in a drawing automatically, i have been trying to see if there was a method with the parameters but when i create the inheritance feature, the file name is the only thing i can refer to, which the file name and PN do not always match. 

I am using Creo Parametric Release 6.0 and Datecode6.0.3.0Creo exit just after launching.Here are the errors that I facedstd.err file generated with below errorpm_is_portmapper_port_busy: bind failed, error = 10013pm_is_portmapper_port_busy: bind failed, error = 10013Recently Changed OS Version from Windows 7.0 to Windows 10.

hiiii,   I am new user of creo and i have one problem.   As shown in Photos i have one plate and one pipe part. i assemble those two parts.   how can i insert extrude with cut feature automatically when i assembled the pipe part to the plate. I knew insert the feature by UDF.   Thanks in advace !!!    

I am using Creo Parametric Release 6.0 and Datecode6.0.3.0Creo not able to start. give fatal error.Here are the errors that I facedFatal error encountered. A traceback has been written to U:/********/traceback.logPlease send it to Technical Support.

When I use Creo Distributed Batch to import STEP files I get the following error: "[-16] Error: Wrong input data format. Model Import failed" The file came from Catia V6 in AP203 with extensions v1 format. It is an assembly and can be imported manually into Creo Parametric 8.0.6.0 with no problem. I note that the ttd file in Creo Batch says "STEP 3D Import of Parts". Does that mean you cannot import assemblies in this way? I have a few hundred of these to import, so it will be very painful to do it manually. Does anyone have any thoughts as to how to import these in bulk?

Hello all, I have attached a sheet with a simple example function where the voltage jumps. This causes convergence problems.  I am working actually more complex signal at a capacitor, but I cant share my actual sheet.Basically my attached example is the same... I have waveform with a discontinuity. Later I do a derivation of the voltage signal.Also I want to do a FFT of this signal and therefore I sample it. In any way I have convergence problems and I dont know how to handle that. Do you have an idea? Here is a screenshot of the sheet in case you cannot open it:  

I've recently encountered an irritating intermittent / delayed problem using Simulate.At some stage during a session, after several iterations, the Results window suddenly refuses to open.  The button, either in the Ribbon or within the Analyses and Studies window, just stops doing anything (although I haven't tried closing Simulate and using the Simulate Results button directly from Creo Parametric).  The only solution I've found is to close and restart Creo (which is obviously a nuisance).Has anyone else encountered this?Creo 2.0 M120, running with Windchill 10.1 M040, network installation.

I have a simple text file that I've been importing to every model in my workspace for a while now.My titleblocks are integrated to read these parameters and automatically fill everything out.This is working great. BUT... Now the engineer wants to change the checker & checker date parameters on everything. Is there any way to import this txt file into every part/assy into every file in my workspace?Instead of opening every part/assy and importing the txt file manually?I really don't want to do this 350+ times. It's actually a .xml, but it opens in notepad. Same as Configs. 

I want to copy this picture. After pasting, only one field appears: "Search image". Can someone help me?   Translated by Andra Chirila using Google Translate on Jan 26, 2023----------------------------------------------------------------------------------------------- Diese Bild möchte ich kopieren. Nach dem Einfügen erscheint nur ein Feld: "Bild suchen". Kann mir jemand helfen?    

Greetings.  I am somewhat able to create a repeat region table containing all of the information I need. However there are certain issues which I cant seem to get past.  Problem 1 : I have a column for cable length, and I populated the top column with the following report string: &mbr.connprm.pin.run.len[.0]. 2 wires in particular is a part of a cable feature, one is displaying the proper length, one of which is not displaying anything. I did not manually assign any manual lengths, so I am now sure how to fix this issue, any ideas?  Problem 2: I have a different column, displaying length again, with the following report string: &harn.run.len[.0]. I have 3 wires as a part of a cable feature, each with varying lengths. In the table, only the longest length of wire is being displayed for all three wires. I am assuming that because this is a single cable, it is giving me the longest length in the wires, but whether I am right or not is what I was

Hi all, I want to use ODESOLVE to solve the set of equations for a given volume (v). On top of that, I want to make all of those equations also depended on the variable CXmin, to evaluate the influence of this parameter on the costs calculated below. However, I run into the problem that I don't know how to set Cxmin as a unkown in the solveblock, causing errors. Can anyone help me making the solveblock solve for the volume (v) while setting CXmin as a, to be chosen, variable too? Your help is greatly appreciated in advance. With kind regards!  

I have created an assembly with the flexible components and controlled its length through variable items. based on the assembly I created the repeat region BoM table in the drawing. but the drawing BoM shows that, each component as a separate line item even though it has the same part number. Also, I noticed that Creo is combining the flexible components that are in same length.  Pls. suggest an idea to combine these parts into single item with correct quantity.  Refer uploaded image..   

Hello, I need to change the location of several in Creo and I'm not finding this path dump_x86e_win64  

My memory must be going. I seem to remember being able to drag a sketch out of a feature in the tree and make it an external sketch so I can use it elsewhere. Can I do this?

Hello, I have been having problems with my Creo 9 (Student Edition) installation.When I try to open the Surface Finish Gallery or the Hatching Configurator I keep  getting the warning that the corresponding file "was created with a commercial version of Creo Parametric and is not compatible with the Creo Parametric Student Edition (for educational use only) you are running." after which the program shuts down completely.I am sure this problem exteds beyond the mentioned configuration files.A reinstallation of Creo did not fix this (neither did a second one).There has not been any other version of Creo installed on my computer, nor have I uses any other license apart from the Student license I am currently using.Is there a way to fix this problem?Is it even wise to use the most recent version of Creo or are previous versions generally more stable?Thaks in advance for any input.