Windchill

Hi,I have created an FTP location in my local system and created a distribution target in Windchill. I have associated it to a part and when I'm trying to perform 'Send to Distribution Target', I'm getting the following warning with no objects in 'Included objects' list.The object XXX being published does not have distribution targets assigned to it.Also, I'm not able to see publishing status in UI.Can you please help me in resolving this..Thanks in advance!

I have the following filters set up in my table view:state      releasedstate      released(expiring)latest     YesIs there a way with these filters set to see the subfolders within my folder. (the subfolders are  hidden because of the filters above).

What is diffrence between Load Base Data and Load Demo Data?

We had a situation recently where we didn't get what we expected when downloading from Windchill to a workspace.   The designer had saved the drawing and assembly file as part of a check-in process. Submitted a promotion request, which was rejected from a bad WTpart EBOM listing. Designer checked out the part and WTpart, made the corrections, checked them back in. Submitted a new promotion request against the drawing, which uses the Load latest rule, and the part/drawing are approved and released. However, the drawing file is pointing to an older version of the assembly and not the latest after the EBOM change. Come forward a few weeks and we go to put the files out to manufacturing, so Add to Workpace is used and low and behold we do not have the latest version model. Nothing was physically changed in the model, so that is ok.   The question being asked is: Is there a way at promotion request time to flag the promoter that the drawing is not utilizing the latest model, even

Hello All,Below are my requirement while SaveAsConsiderations:Hardware parts should come as Reused (Hardwares Library)Drawing Formats Should reuse (Pro_Standards Library).  Procedure:  Save as of any assembly from commonspaceThe collector window should not list the formats and Hardware componentsThose library parts should be considered as Reused.Note: This can be achieved by strike through the rows by location.Awaiting for your valuable reply.

How to view my Service Effectivities [i.e. Serial Numbers, Model Numbers] applied on Parts? under Structure Tab or any layouts? or any DB query to extract Effectivity on Parts?

Would anyone have some thoughts on how to insure that a user dose not have any locally modified files that are associated to a Promotion Request?Scenario:User revised and checked out a drawing File is opened, modified and saved.In workspace file shows as being checked-out and modified.User exports a PDF of the drawing and checks-in modified file.User creates a new promotion request associated to the file, and attaches the PDF to the ECO in Agile.The design-review team reviews the PDF and finds a mistake on the file and kicks the promotion request back. The file is still in the users local workspace, he opens it and when he initiates the change for whatever reason chooses "Continue" instead of "Checkout"Because he selected "Continue" the modifications are saved.He creates a new PDF that he attaches to the ECO in Agile.In Windchill he resubmits the promotion request.The design-review team reviews the new PDF and approves the ECO in AgileDoc-Control approves the Promotion Request in Windc

<<<Applies to you if you are using Windchill publishing with SolidWorks data >>>(I still shudder every day about going over to the "dark side" of SW, but it's interesting and mainly from acquisitions - similar for many companies and life goes on)Learned recently that the Creo View adapter on the CAD Worker behaves as follows (different from Creo Parametric publishing): If the recipe file is set to "Fail Publish for Missing Dependents=yes" then it fails every SW assembly / drawing for which any component is suppressed - including intentional suppression of SW configurations (handled as Windchill family table instances).Because of this, we have no choice but to leave "Fail Publish for Missing Dependents=no."PTC just published this article based on our tech support case: CS257786 https://support.ptc.com/appserver/cs/view/solution.jsp?source=subscription&n=CS257786So I'd like to create an Idea here suggesting that PTC change this to match Creo Parametric - allow Suppr

We went from Windchill 10.0 to 10.2

can I get an excel list of non-functional requirements for Windchill 11.0

What is the best practice for being able to split quantities into different operations.  We are a bit confused here on how to proceed.   Assembly:  410-158444 Child parts:  401-158888 (QTY 4) needs to be split between 2 operations in the process plan.   Do we make a manufacturing view of this part, add another instance of 401-158888 with a qty of 2 and then from the occurrences tab reduce the number of the original 4 to 2?  Please provide any details you can (what UIs Explorers or browsers) to achieve this.   We have quite a few assemblies that the design view could be used in the process plan - except for the allocation of qty to operations.   Thanks, Greg

Hi all,   I'm a little bit lost. We are going to move our server infrastructure from 2008R2 to 2012R2 including all my Windchill visualization workers. A first test has shown that moving a Creo 3 worker from 2008R2  to 2012R2  is not an issue. When trying to do the same with SolidWorks 2016 worker I ran into a problem. GS Worker Deamon starts a SolidWorks.exe process but this stops immediately after launch - regardless if the Service is running with user permissions of a logged in user or with SYSTEM and "Allow service to Interact with desktop". It seems that Solidworks does not know where to display it's gui... has anybody experienced the same or knows how to allow the application to pop up on the desktop or virtual desktop? launching the swworker.bat interactively works fine ... just when launched by the service it stuck.   Thanks, Stephan

Back in early December, I downloaded all of the installation media that was available for WC 11.0 M020, and when I look at the list of available media today, 1/13/2017, the Service Pack download for M020 is not listed.  Even the webpage with the list of available software updates is missing the Service Pack listing despite the other M020 components being available.Is this on purpose to prevent installation of M020 or is this some "glitch" in the downloads site?

Hello, I can not use illustrate to insert a JT profile,the problem is as follow:"Path to log file: C:\Users\YANGBI~1\AppData\Local\Temp\PTCg032c6gg0vuq0\IMPg03im5ug0vuq0\conversion.logjt2pv - Version : Creo 3.0 - M030 (13.2.30.38) x86e_win64Copyright (C) 2000-2015 PTC Inc. All Rights Reserved.jt2pv Error:3000: Failed to open registry file "D:/x86e_win64/jtopen/recipe/jt2pv.pvr".jt2pv Error:10001: Failed to load "jt2pv" default recipe file [D:/x86e_win64/jt"Can you solve this issue?

i am not able to checkout cad part, as i was doing earlier. All drawings & parts are in inwork state & it shows user don't have necessary permissionwhat must be the reason?

I have my eBOM structure and sBOM Structures with Service related attributes, is there any way to compare both BOM's and generate reports by using tool?

can anyone help on finding what is the java api to get the products under a particular organisation ??  how to retrieve all the  organisations in a Site , the products in  each organisation.

I have some IBAs for example iba1, iba2 & iba3.  My condition is I want to make iba2 & iba3 as required/mandatory only if iba1 value is entered in from the UI. How to I achieve this programmatically? Any APIs? Or Logic? Thanks.

I'm new to windchill customization . Currenly working on windchill 10.1 .I've just learnt to create actions  . Now i would like to know about creating a  attribute panel configuration. As in creating an action . upon clicking it i want to display certain details . adding groups in panel etc. can anyone help?

  Hello all, What is file vault in windchill and why we use that?

Dear All,I need to know step by step guide, How to replica server pro intralink 3.4Please give me a tutorial or document success step for newbie.Thank you in advanceRegards,Surached

Importing the Project templates from Windchill ProjectLink 9.1 M050 to 11.0, and from ProjectLink 10.1 to 11.0 F000 fails. Do you have any recommendations on how to import cross release project templates?

Main Translation Process Bottleneck – ReasonsIncreased volumes of parts books to be translated2nd or 3rd translation package needed to completely translate mediaSignificant amount of translation requests for just a single languageAdditional translation requests - ReasonsAuthoring process „exceptions“ causing need for retranslationProduction partlists being iterated (e.g. to add / change modifiers)Production media being renamed (e.g. OMM name updates)Publishing failing if no new Xliff is generated and translated (for partlist or media)Media baseline used in publishing doesn‘t reference the modifier objects – so always using latest (with changed name / modifierString)Media rename doesn‘t iterate the object, so media baseline still valid, but information that was exported and translated through the Xliff is outdatedIn both cases Translation Dictionary doesn‘t have translation for latest strings, therefore publishing failsCurrent „process“ is to manually force creation of new Xliff (Suppor

Dari  (PRS) is currently not supported by Windchill. We need support for ISO 639-3 to be added to Windchill so we can eliminate manual desktop publishing and reduce translation cost and turnaround.

My company has a need to create a report of routings being done in ProjectLink Projects.   Ideally we would like to report on the following:  (See Screenshots for examples.) Routing Instructions Participants in the routing Participant Comments Participant Votes State of routing   Before I spend much time walking down a dead end, does anyone know if this can be done?   Or how would you approach solving the problem?   -marc