Creo+ and Creo Parametric

I'm a mechanical design,I need to measure a lenght of section curve.Actually I work with PROE WF4 or CREO8Why with a singolar measure, exact with geometrical calculate, is different of a measure withsection curve.On example 2667.4601versus 3984.22.Many thanks for the answer.

I am using Creo Parametric Release 4.0 and DatecodeM080facing problem in editing drawing,Regards,Gauraw Singh

Hello, I want to know how to list all licenses under a customer's name, not only current used licenses but also historic license records. There is a License Reports weblink at esupport website, I tried but not sure if can list all licenses or not.https://www.ptc.com/support/license-management/report Thanks. 

Hi, i would like to ask if is possible to hide the text that I have surrounded by the red circle.thanks.

We (our company, not me) have been routing harnesses for a long time with the old flattening software.People are asking if there are any good tutorials or informational items how to use HMX.

Let me first try to explain the issue. The below graphs are the pressure forces observed in Creo flow analysis (Figures 1 and 2). When I compare these results to the hand calculations  (Figure 3) I made, there is a stark difference. But when I compare the hand calculations to the reaction force (Figure 4) I see in ANSYS (which uses the pressure distribution from Creo flow analysis), the values have a smaller percent difference. I also have ensured that the unit system is correct (Figure 5). So I guess my question is: Are pressure force and reaction force the same?

Hi,   When creating a dimension in 2D, Creo highlights one direction of the axis. When select axis via ProSelect(), Creo highlights all direction of the axis.   Is it possible to highlights one direction(at cursor) of the axis when select axis via ProSelect().?   Thanks, Warm Regards, SeonHo CHA.

Hello I see this PTC article: CS50932 Snapshot is not updated in drawing for a flexible component But PTC says it's article is available for: Creo Parametric 1.0 to 4.0   Anyone know if it's OK for next Creo's version ? I have Creo 7 and obviously it does not always work   It's a problem because the PTC circumvention is not applicable (make flexible componant in 2 hard componant) It's ok when you have not much part but it's impossible with a lot of part it's a shame because the principle of snapshot is very great and light comparatively to Solidwork's configuration Anyone can to help me ?  

Limits according to FKM

Hello all,  I would like to simulate a column steel plate supported on a concrete slab. The load is in the downward direction so basically the steel plate induces compression on the concrete surface. Material definition in CREO simulate, seems oriented to metals only? I tried defining the stress-strain relationship of concrete with 3000 psi strength but I haven't been successful. Is anyone aware of any work-around for brittle materials?  Thank you 

Good morning, beacause I am a newbe in Creo Simulate I need a help for modelig hinges screws.I have a 3D mechanical frame where connection are made by hinges and screws. For the hinges, following the description in the description in these linkshttps://community.ptc.com/t5/3D-Part-Assembly-Design/Hinge-Deflection-Simulation/td-p/94974https://www.ptc.com/en/support/article/CS349520the procedure is described below:- put 3 points for my beam elements (two at the edges and and one at the middle span) - Image 1- I created my two beam elements using the Point-Point Pairs option - Image 2- set rotation releases in the edges of every element - Image 3- set rigid links between the points and the inner surfaces of the holes - Image 4At this point I need to understand:- has the hinge been well modeled?- can I model screws in the same way, just removing the rotation releases?Many thanks in advance

We are using creo version 4.0- We are trying to connect to the floating license server- I enter the server info after I run the reconfigure tool- We keep getting the unreachable status after we enter the server infoWe may need another license or remote sessions to resolve that status.

subject: Dialogs generated by Tool kit are automatically closed.   I am using Creo Parametric Release 4.0 and DatecodeM140    When developing the dialog function in Creo Toolkit, click the button, call the ProMacroLoad function, load the macro command, "~ Command `ProCmdEnvAnnotElemDisp` 1" to realize the display annotation function, but after the function is executed, the dialog box will be automatically closed. Is there any way to keep the dialog interface from being closed?   Translated with Google Translator by Hedy Jin on Jun 2nd, 2022   ---------------------------------------------------------------------------------------- subject: Tool kit生成的对话框被自动关闭    I am using Creo Parametric Release 4.0 and DatecodeM140 在Creo Toolkit开发对话框功能时，点击按钮，调用ProMacroLoad函数，加载宏命令，"~ Command `ProCmdEnvAnnotElemDisp` 1"，实现显示注解功能，但是执行完该函数后，对话框会被自动关闭掉，有没有什么方法可以保持对话框界面不被关闭掉？

Good morning, I ran stress analysis on 3 design options with 3 different convergence methods. The maximum stress results are shown in the diagram above. How to interpret it?1: Design-3 is the best? 2: Never trust Quick-Check (QC) and Single-Pass Adaptive (SPA)?3: Always run Multi-Pass Adaptive (MPA)? Thanks.JS

Creo 4.0 M060.   I recently (actually is has been a little while, but I just figured it out) noticed a change where after editing a dimension in a model, I used to click the middle mouse button to accept the change. Now I have to click the left mouse button twice. It is not a big change once you figure it out. Has anyone else noticed other changes? Thanks, Dale

@Hello All,Please find below the attached file "frame.prt". This creo part has an parameter named password .you can see the features of part only by providing the right password followed by model regeneration.Good Luck.....RegardsAnandkumar P

I am wondering if it is possible to create a repeat region inside of a drawing that can list all models (active and inactive) that are associated to this drawing.

I am using Creo Parametric - Release 4.0 (connected) Release 4.0 and DatecodeM070I'm trying to take a surface of a part and cut it into another existing part by using solidify but I can't seem to get it to work.

Hi , I have suppressed UDF Feature , But dimensions associated with that feature need to be suppressed or delete automatically , But it shows a warning message , The problem is without clicking my program does not step up and end  So I need a solution to avoid warning message Regards,Kunal B.

Hi , I am working on drafting project , where I have to move dimension from one view to another , under annotation I find option like "Move to view " But I did not find any API related to this , Please help me to resolve the issue . Thanks & Regards,Kunal Bidkar

I am using Creo Parametric - Release 6.0 (connected) Release 6.0 and Datecode6.0.3.0We have configured Custom Config.pro and custom Config.sup files. One thing that I have noticed is that Creo has taken a direct degredation to how smoothly it ran and how quick it loaded parts and assemblies. Could there be issues with the Config.pro and the Config.sup files have an impact on how long it takes to load data.As a note, we are integrated with Teamcenter using IPEM. If I run the integration without, the custom "/sup, and /pro" files, I don't face any issue, which leads me to believe the issue lies in the Config.pro, and config.sup files that we updated.

Hi,  I have a problem with the following: When I in my 3D model suppress a feature, then in my 2D drawing the dimensions related to that now suppressed feature won't disappear. Does anyone have an idea how to fix this?  

Here is a model for Creo Simulate to test the computational performance. A "good" PC should take well under 2 hours to compute.

Welcome to Creo Tips and Techniques Series  Main Presenters:  Ryan Butcher (Technical Specialist, Fellow) and Lino Tozzi (Technical Specialist, Fellow) Below you will find all the related webcast recordings and recommended additional learning resources.    Webcast Title Description Learn Online Classes/Resources 1 Learn Online Classes/Resources 2 1 Creo Multi-Body Design Creo Multi-Body Design Creo: Multibody Design Class Info   2 Creo and Augmented Reality Creo and Augmented Reality Augmented Reality Class Info   3 Creo:  Generative Design Automated geometry creation using design criteria Creo: Generative Design Class Info Creo Generative Design Tutorials 4 Creo:  Simulation Live Real time simulation during design Creo Simulation Live Class Info Creo Simulation Live Tutorials 5 Creo:  Flexible Modeling Direct modeling features to edit imported data Creo: Flexible Modeling Class Info Creo Flexible Modeling Tutorials 6 Ansys Simula

It surprises me that, while running through the different PTC forums, I did not find the answer to a lack in Creo Parametric that seems so obvious to me and to other users who have worked with other CAD systems like SOLIDWORKS, Inventor, NX...In all these CAD systems, it is possible to select the midpoint of a line or an edge (eg to measure between two midpoints). No problem at all. In Creo Parametric, this simple functionality isn't available at all. Or am I wrong? Any comment is appreciated, as long as it is polite!Kind regards,Philip Olieux