Creo+ and Creo Parametric

hi.   i'm a fairly new user to CREO and still learning. can someone let me know if there is a way to get the drawing view contents to stay visible whilst you are moving the view. would make it much easier when tidying up my drawings if i could see what i was moving.   thanks

I have some parts and assembly that have paramters that are locked because they were created in Interlink. How can I unlock these parameters so they can be deleted?

I would like to know how can I change the Pipe Diameter from a piping segment.   I made my design not using the "Spec Driven" option.   I tryed going on "Modify", in modify Options marked "Line Stock", then I selected the segment, and finaly on the "Modify Linestock" I changed from the 4 inches to 3 inches as I needed. The problem is that the Ok button is greyed-out. I even tryed to create a new and added a new linestock it stays the same.     OK Greyed Outnot spec driven

I have a family table that I am building of hex head screws. I want to put the material marking on the head and it varies depending on the nominal diameter of the screw. I have created the 2 markings and currently have them added to my family table so a Y or N will select the proper one. Since I have the diameter driving the head in an IF/ENDIF section in the relations, How do I add a feature inside the IF/ENDIF segment for each size.Something like this:IF basic =='1/2"   nominal = .500   hd_flat = .750   hd_thk = .375   fid:head_mark_c = yes   fid:head_mark_d = noENDIFIs that even possible in a relation or must I move some of this code to Pro/Program? I will probably leave the Y/N columns in the family table if I can't do it in relations.Creo 2 M240Windchill 10.0 M040

We have revised some old symbols that used to be Upper/lower case lettering to be all Upper case lettering. The old symbols are relocated to another directory, not under the current pro_symbol_dir defined in config.pro. When we go to select the symbol, the preview window shows it like we expect, all upper case. When it is dropped onto the drawing, it becomes the old Upper/lower case symbol. Using Windchill, no other drawings in the workspace or loaded in memory as the user erases all not displayed between drawings. We are on Creo 4 m080.   What would cause the system to grab a symbol from another directory that is not even a sub-folder of the main directory defined by pro_symbol_dir. The really confusing part is that sometimes we will get the all uppercase symbol.  

Is there an option in Creo that upon creation of a plane, the size of the plane is scaled to the size of its references.  the option is in the plane menu but a PIA to do this every time.  

We would like to see customizeable shakeways within sheetmetal NC like it is ruled out in  article 325903  If there is anyone craving this functionality please let us know and vote for our idea

I modified the restricted_paramaters.dat file this morning for a new person added to the checker drop down. When the user went to do his update, Creo said the file hade conflicts and he did the update. The new person got added, but when he went to another parameter to select a name, it did not show the list that is in the restriected_parameters.dat file. So the update did some of the parameters but not all. Really strange. Has anyone else seen this behavior.   Creo 4 m080  

my client got this error today with his creo it then crashed any idea what caused this?   traceback attached

Is there a config option (hidden?) that will set the default axis length for the zoom-dependent property for a coordinate system. I know I can change it. And I have to, every time. It has a default right now of 37.060 inches. I want it to be 3 inches. Haven't been able to find something on this. I know there is a hidden option for the name text size, but haven't seen anything on the axis length. Using Creo 4 M060. (We are not fast to upgrade!)   Thanks

I have a short video to share on "Managing Casting and its upstream model appearances".  Check this out. Share your experience and best practices in the comments below; Thanks.

In my company, from last year I had to work on different workstations, based on their availability after shifts. And it can be hard for anyone, who has different files and folders in his dedicated system. In an organization, work files and folders can be neglected for some extent when you work in PLM and you have different logins to store the files from the network folders. You can access them from any device, anytime.   But when you have your software settings in your system, you will feel the real pain of migrating to new system, so did I. After studying the customizations storage path, I have learnt that I can avoid this UI gap in other systems in a simple way. I have made a short video on this. Please check this out.   In todays situation, when we are working remotely from system to system, we can definitely go mobile with UI and be more productive as we are on our own system.  What is take on this, please share in the comments.

I have an assembly with thousands of parts made from various aluminum extrusions. All of them have been assigned a material named "AL6061", and that material file has a custom aluminum appearance assigned to it, which is stored in the global.dmt in the materials folder. "global_appearance_file" points to that, and I have "mat_assign_appearance" set to yes. Everything seems to work fine, until......I need to change the generic aluminum color for some reason. I can load the global.dmt file into the editor, change the appearance, and then save it. Or do it manually or any other way I want. I can verify the changes are in the global.dmt, but the part colors never update unless I un-assign and then re-assign the material. Even with some scripting and automation, this is a tedious task on thousands of parts buried in configurable assemblies.This leads me to believe that the appearance definition is loaded into a part when a material is assigned, and stored with the part. If so, that is

Is there a way to quickly update an inheritance that is set manually update?   I have a model that I am using to drive many other models by turning on and off several features.  To prevent regeneration errors in upper level assemblies I have set the inheritance to manual update.  If it is set to automatic update, it will update during regeneration is the base model is in memory.  Also, there is a command, update inheritance in the RMB menu.  The update inheritance command (which sounds like a manual operation) is not available if the inheritance is set to manual update.   I have to edit definition to change it to automatic then edit definition again to change it back to manual.   The only method I have found so far, to speed up the process, is to use a mapkey which requires no deviation in the command flow such as checkout warnings.

Imagine having an assembly with patterned groups of bolts and nuts of different sizes. You want to include these components in the family table. The menu manager asks single or all. What does this mean? All components in the group? In the pattern? In the subassembly? In the main assembly? Does it make sense the menu manager even asks for this? In a pattern, the components are supposed to be the same right? Where can I see if CREO picks a single one or all of them? How can I change it from "single" to "all" and vice versa?    

How to calculate total weight of assembly in PTC Creo Parametrc?  

Hello. I'm new in Creo (version 6.0.4)  and I've a problem with color in drawings. I like the default color in part and assembly mode (with blue geometry when see the part in wireframe). But in drawing I want all the geometry black. If I change the color of geometry in System color from blue to black, it change in part mode and also in drawing mode. There is a way to change the color only in drawing mode?

Hi all,   I am running Creo 4.0 M050. On installation (a few years ago) I set system environment variable LM_BORROW_DURATION  to a value of 179 to allow for a longer period to borrow the license. I don't recall I was ever able to borrow for that maximum number of days. Around 150 days, more or less, that would work. I usually would start at ProE_Borrow with a value of 179, get an error 'Can not borrow that long' when Creo started, and decrement that number until Creo would accept it. Yesterday, I had to go as low as 35 days to borrow before Creo would accept it. So, there seems to be another mechanism besides LM_BORROW_DURATION that limits the number of days that you can borrow. Does anybody know what it might be? And how I can get around it?   PS. You would think that if Creo knows that it 'Can not borrow that long', it would be kind enough to let us know how many days it CAN borrow .... 🙄  😉   Kind regards Eddy

So the problem was the user would right-click on objects in the Reference Viewer and not get the menu commands to show.PTC replied with a request that we update video card drivers. I did that along with a bunch of other things (see below) and the problem remained.HOWEVER - I just started playing with all the controls on the Reference Viewer and discovered that if you shrink the window so that scroll bars appear in the reference viewer, and use the scroll bars to lower or raise the viewer, then the right-click menu will appear (see attached image).Weird. But it works.Thanks everyone for your suggestions. For future ref, here's the list of my notes:NOTES:- updated build from M190 to M220- removed config.pro & config.win files- started ProE in vanilla mode (no configs, start dir, start parts, etc.)- rolled back video driver (reinstalled current after testing failed)o previous = nvidia quadro fx 580 9/12/2009 8.16.11.9100o current = nvidia quadro fx 580 12/4/2009 8.16.11.9175- performe

 

So I have a mapkey that exports a part to make it to a symbol. A problem I've found is that if csys and datum plane display is on, that will tend to be exported with it. No problem! I add an instruction to turn off the csys display, right? I know I've done this before. I record one and look at the code:   ~ Command `ProCmdEnvCsysDisp`  0;\   This should turn off the display of csys. Problem is, if the display is off, this is turning the display on! And this version:   ~ Command `ProCmdEnvCsysDisp`  1;\   Does exactly the same thiong. It's toggling, rather than turning on or off. I know in the past I've been struggling to GET it to toggle, rather than turn on or off (and there are old Community threads attesting to others struggling with the same thing), but now suddenly I can't get it to NOT toggle. Has this behavior been changed? How can I get the mapkey to turn off the display of csys if it's on?   I'm on Creo 4 M080, so it's not even a very recent

I'm a little off the path on this program so bear with me... Everything I am doing is happening in unmanned batch mode using toolkit. I am importing Step model assemblies into session, not linked to Windchill. I am then linking to Windchill while keeping these objects in session.   Objects with the same names as these just imported already exist in Winchill as placeholders.  These placeholders are .asm files that only contain a csys, and they are assembled into this master assy, using Csys contraints. (one simple constraint). Result is the assembly has these imported step files assembled in place to csys.Issue is, Creo realizes the component csys is not the same. So what I am looking to do is fix the component constraint, basically redefine.  ive read up on TK assembly, there is a lot there to grasp, and have studied the UG constraints.c sample. I want this to be as easy as just updating the contraints. The TK guide example is all about user interactive selections a

Hello community, I am using Creo version 6 (educational edition) for a couple of days now and designed a part which I would like to manufacture by using some milling processes. To do so, I click on file -> new -> manufacturing -> NC assembly -> ok, but the screen with the manufacturing options doesn't appear. Could someone please give me an advice of how to solve this issue? 🙂 Thanks for your support. MLC89

Hello all.   My previous coworker created a mold … and i want to be sure it fit with what the demand of our customer.   Is it a way to "fill" this mold and get the actual part ? If not, do you know any tips to do it ?

Gears tutorials include base steps: How to create gear connections in Mechanism mode and definition of gear properties, analysis and animation.   You can capture the following motion relationships using generic gears: Rotational/Rotational Rotational/Linear Linear/Rotational Linear/Linear   Examples of the four dynamic gear types include: Spur — Two meshing gears rotating on parallel axes Bevel — A pinion gear driving a crown gear on perpendicular axes Rack and Pinion — A pinion gear meshing with a sliding rack gear Worm — A worm shaft rotating a pinion on perpendicular axes