Archive Read Only

Is there a way to have a 'Copyright Protected' notice pop up whenever an IGS file (or a STP file) is opened?I have a need to send an IGS file to an external organisation with which we have a NDA in place, but they may need reminding (preferably each time they open it) that the data is ours, not theirs.I think I probably know the answer...If I'm correct, how have you folks dealt with this problem?Cheers,John

Hello group,We have a couple users starting to get errors when opening up files. It started with opening numerous files and then eventually when opening another large file we get an error:

Dear all,I am trying to call a mapkey, that I have already defined in CREO, from excel's VBA.Is this possible ?I would would be thankful for the help Regards, Nicolas

I have an IGES model from a supplier for a piece of equipment that will be used on a tractor. The model imported as a set of surfaces so the model mass and center of gravity are currently incorrect. I know what the mass is and I have a rough idea of the center of gravity so I would like to assign these values to the imported model so that the CG and mass in my tractor model is correct. The problem is, I can't seem to figure out how to assign mass to a point. Anyone have any ideas?

when i start to download Creo 2.0 M090 with download manager it starts and then says "error" and then stops?did anybody face the same issue?what could be wrong?i have treid using inter explorer 8 mozilla and google chrome

I'm wondering if anyone has done any work with Splines and holding the length to a fixed value? This assumes that the endpoints could not get any further apart than a straight line, but as the ends got closer together (by way of some other constraints) the spline would "buckle" (for lack of a better term) to mimic the behavior of a semi rigid component (like a hose).

How to change the spline line properties in partial view in 2 d ex: i want to set the partial line boundary like phantom , centreline or so on ?

Does anybody know how to get an angular dim as shown in the image? (in Creo Parametric 2.0),

Have attached image for your refernce .It would be better if some one have created & share the profile

Does anyone know how to change theSpline Boundary Line ofa Partial,or Detail View?I know there is the option tonot "show spline boundary on view".I cannot seem to find away to show Spline Boundary Linewith a different line type. A way around thisI sometimes remove spline display line and manually sketch in a spline and thenchangeline type. It's too much manual work and I always have to re-adjust it whenthe view boundary changes. I was hopingsomeonemight know away to solve this.I`m currently using Creo 2.0 Parametric 2.0

Hi again, Also, where is the Materials Folder? (and WHY is it so hard to add a newmaterial to it?) -Nate

Is it possible to add custom profiles to the framework.The rectangular and square tubes are with rounded corners and for calculating purposes we need them to be straight.Also for we use custom profiles for our customers.We used the same trick in Inventor, but in Creo I don't know it this possibility is here

I just had a phone conversation with a guy that sells 3D scanners. He doesn't sell any of the scanners that will do what I want, so he didn't have an axe to grind.He's been in this industry for quite a number of years and according to him, none of the scanners I listed will do what I want.He suggested the following scanners for doing room scans. None of these are cheap, but they do exactly what I was looking for a scanner to do.Surphaser

Once a parameter is created, is there a way to change from the Parameter Type (ex: String, Real Number, etc) after hitting the OK button?? Or do you have to delete the parameter and create a new one??

We just migrated from WF4 to Creo2. in WF4, once we completed a dwg we alwaysused the show/erase dialog as a fast way to check if the dwg was fully dimensioned. Please tell me there is a fast way to do this in Creo...?Does anyone know how to quickly show all dimensions (or "annotations") regardless if they were "errased", or "deleted")?Thanks, Lawrence

I am printing out a model (parts on a fixture) and I have annoations that show up. This only happens on a few prints. Any thoughts on what may be causing this and what I need to change to prevent it.See below:Thanks, Dale

Hello everybody,In our company we are new to using Creo parametric. Comming from Inventor it is a pretty big adjustement.A simple thing which I don't seem to figure out is how to convert a project line to a construction line. A normal line I can convert with holding right mouse button and selecting it. But for a projected line it isn't there.ThanksBerry

My maintenance invoice went up 3% this year. Anyone else experience this?That Makerbot sure is looking like a bargain compared to PTC maintenance!

Hallo zusammen,bisher ist mir hier im Forum immer gut geholfen worden.Daher möchte ich die Zeichnungsvorlagen nach EN ISO 7200einstellen.Mit freundlichem GrußWerner

Dear all,I want to know about skeleton modelling.what is the advantages of it?for non symmetric model can I use skeleton modelling?

I have searched for some answers but I am still confused. What is the different between all of these and are they all needed?PROE_WORK_DIRPDM_LDB_PATHPTC_WF_ROOTPROE_START_DIR Steve G

What is the macro language for Creo?

Anyone have any data comparing performance or stability of Creo 2 on 32-bit vs 64-bit? We have discovered a big difference in stability on Wildfire 4.0 but I need data on Creo 2. I have searched for similar discussions here and have been unable to locate this specific discussion.

I am not able to display hidden line in creo paramatric 2.0

Qualitätsagent, der in dieser Ausgabe erforderlich ist, nicht ausgeführt werden kann. Fehler 0x06000012