Creo+ and Creo Parametric

I am using Creo Parametric 3.0 M110Server WS の Windows の更新後に、Flexlm server for PTC が立ち上がらなくなった。・2021-05ｘ64 ベースシステム用 Windows 10 Version 2004 更新プログラム (KB4023057)・2021-02 .NET Framework 3.5 及び 4.8 の累積的な更新プログラム (x64 向け Windows 10 Ver 2004用）（KB4601050)Here are the errors that I faced ローカルコンピュータ上のFlexlm server for PTC は起動して停止しました。サービスの中には、他のサービスやプログラムで使用されていない場合は自動的に停止するものがあります。

I am trying to model a nose cone/end surface with G3 surface conditions (as shown in the image below/file of model attached). I am using PTC Creo 7.0/Style.   I'm trying to achieve a G3 surface condition on all 3 domed sides and a normal constraint around the bottom perimeter.    So far I am only able to achieve a G3 condition on the central curve/surface and a normal condition around the bottom perimeter. When I try to increase the two surface conditions either side of the central plane from a G2 to G3, I get the following error message:   "The cross curves are not connected with the same continuity as the connection"   I'm not sure what I am missing here? It would be great if you guys could take a look and tell me what I am missing? 

I have the following relation in my relations for a BOM that simply removes the specified cage code:     IF exists("asm_mbr_cagecode") IF asm_mbr_cagecode == "12345" my_cagecode = " " ELSE my_cagecode = asm_mbr_cagecode ENDIF ENDIF      Which has worked as intended, EXCEPT I am now noticing that there are a few parts in my BOM that are pulling the incorrect cage code from another unrelated part. Without the relation, I don't have this issue. Not sure where this issues may be coming from.

Bonjour, J'ai besoin de savoir comment faire pour ajouter un paramètre dans un dessin dans un tableau qui est lier aux instances d'une famille de pièces.   La dernière colonne devrais varier mais elle réfère toujours uniquement a la pièce générique.  

I am using Creo Parametric - Release 2.0 (connected) 2.0 M150HI, Could you give us best practices for configuration of the nvidia control panel. Our computers are running parametric 2.0 M250 and 5.0.6.0 and simulate Our graphic cards are Quadro RTX 4000 (on Dell Precision 3640 Tower) Thanks a lot. François

I found this video from SolidEdge, and I found it very usefull   https://youtu.be/pPCrpZyi1RE?t=272   This video from NX with samething https://www.youtube.com/watch?v=oEeNlSsp5e8     Basically, on a surface or a quilt, it's possible to create a curve with an angle from a reference, like a shadow. How to create it in CREO?    

I am using Creo Parametric - Release 7.0 (connected) 7.0 7.0.2.0When using Simulation Live for a structural analysis of an assembly what spacing is required between the parts so that they are not considered bonded together. It appears that I need more than 0.1" before they are treated as not bonded together. Is this accurate? Can it be changed? I work with parts in the size of a handful of inches and this gap can make significant changes to the design in order to get the parts to behave as not bonded together.Thanks,Chuck

I am using Creo Parametric 7.0 7.0.2.0Every time I save a drawing I get this “Model Check Report” blank dialog window that opens on the left side of the screen and doesn’t close until I hit the “X”.Here are the errors that I faced Blank Model Check Report.

Hello everyone,I wanted to copy a measured value and pasted to txt file, however, I failed, first, I right-click the value area (1874.84 shown in Figure 1) and click ‘copy’, then I pasted the value in txt file, but there is nothing to be displayed, I do not know why this happens?Any advice will be highly appreciated, thx!Regards, Figure 1  

I am using Creo Parametric 2.0 F000最近两天在退出机构界面的时候 会导致电脑系统崩溃，要重启电脑才可以。   ---------- Quit creo 2.0 causes the computer to crash I am using Creo Parametric 2.0 F000   The computer system will crash when exiting the organization interface in the last two days, and the computer must be restarted.

Hi,   i have all set up VB api in my pc along with i have marked vb reference in creo as well but when i try to run below code i am getting error;   'globale Variablen:Dim asyncConnection As IpfcAsyncConnectionDim cAC As CCpfcAsyncConnectionDim hSession As IpfcBaseSessionDim hCurMdl As IpfcModel Function Connect2ProE() As BooleanSet cAC = New CCpfcAsyncConnectionSet asyncConnection = cAC.Connect(Null, Null, Null, Null)Set hSession = asyncConnection.session Connect2ProE = TrueEnd Function Private Sub but_connect_proe_Click() bProeConnect = Connect2ProE() End Sub     your help really be appreciated. Thanks  

Hi Folks!   When creating a HSM roughing NC sequence I've set the config option mfg_param_auto_copy_from_tool to 'all' but the finishing speed and feed data for the selected tool are written into the parameters, not the roughing ones.  If I create a Rough or Volume Rough sequence it imports the roughing speed and feed as I would expect.  Am I missing something or is this a giltch?   Thanks in anticipation,   Clive

One example of Unconventional modeling with Creo

Hi,   The toolkit get resource(TEXT_DIR) only once when a start Auxiliary Applications for one.So another toolkit app can not get a resource(UI files, msg_file, etc..) they need to start or use it.   Because "Second-TKAPP" starts after "First-TKAPP", only the resource of "First-TKAPP" is obtained, not the resource "Second-TKAPP".   As the toolkits are launched in different locations, is there a way to get their respective resources?   Thanks,Warm Regards,SeonHo Cha.

I am using Creo Parametric 3.0 M190In trying to run parametric in a script, it fails to start. Also, the CS116805 support doc seems not to be available:Note: This article 116805 is not customer visible.Here are the errors that I faced application error: exception : ProEngineerStart returned ProError: PRO_TK_GENERAL_ERROR(-1), proe_path: "C:\Program Files\PTC\Creo 3.0\M190\Parametric\bin\parametric.exe" -g:no_graphics -i:rpc_input "C:\Program Files\PTC\Creo 3.0\M190\Parametric\bin\parametric.psf" %*, prodev_text_path: . Creo may fail to start if the Welcome screen has not been disabled.Start Creo manualy and check "Do not show again" in the "Resource Center" window. See also https://support.ptc.com/appserver/cs/view/solution.jsp?n=CS116805

We are currently running a DELL M6800 Precision laptop with Windows 10 Pro, 64 bit, SSD, Intel i7-4810MQ CPU, 32 GB RAM and a NVIDIA Quadro K4100M Graphics card.   We have had this for several years and are looking at getting new laptops.   Our company will only but DELL laptops.   I have looked at the Support Platform documentation at PTC.com for CREO 4.0 and CREO 5.0 but I cannot find any certified DELL laptops using Windows 10.  The only DELL workstations are towers.   Anyone have suggestions or a list of PTC Certified DELL laptops running Windows 10 Pro 64 bit?

Hello   I want to create a UDF to automate engravings. The engraving consists in the Extrude of a text value, having a hole and 2 planes as references. I was able to create the UDF, and automate the engraving, but I want to be able to have the text as a variable that I can change when running the UDF. Ex: IN1, IN2. IN3.... Is this possible?   Thanks      

Is it possible to save my list of tools in pdf format or print?

So basically I was using Creo 4 and use to have the minitoolbar for AFX and IFX now I'm on a brand new install, and I missing both. What do I need to do to bring back the minitoolbar for buw products?

I thought that the trial period was 30 days but I got a popup saying "Time Remaining - Your Creo Parametric8.0 trial will expire in - 18813 days, -19 hours and -9 minutes.", is it an error or whats "18813 days" mean? Also, after 30days I wont be allowed to use trial anymore or will be able to use some of the functions still?    

I am using Creo Parametric 3.0 M140When we work on a drawing a user get an EXCEPTION_ACCESS_VIOLATION errorWe get the error when:"I open a .drw file, with views, notes, tables and dimensions inside, I copy a table and paste it, then I try to position it and the error appears.• I open a .drw file, with views, notes, tables and dimensions inside, I create a section and the error appears.• I open a .drw file, with views, notes, tables and dimensions inside, I try to open another .drw file and the error appears before I even open the file.• I open a .drw file, with views, notes, tables and dimensions inside, I try to open a 3D file and the error appears.• I open a .prt file, try to open another .prt file and the error appears."Here are the errors that I faced The trace creation timestamp is: Mon Jul 12 15:27:06 21The executable build timestamp is: Mon Jul 24 15:19:28 17The datecode is: 2017170The pro machine type is: x86e_win64The process ID is: 12488The traceback type is : CRASHThe logger

Hi All, I've searched around a bit with no luck thus far. Hopefully this is an easy question.I'm analyzing a mechanism similar to a universal joint with an output shaft angle that differs from the input shaft angle. My current goal is to plot input angle vs. output angle.I see angular velocity as a measure in mechanism, but not angular position / rotation. I've set up a user defined measure for angular position based on x displacement & some simple trig, but this obviously isn't accurate once you change quadrants. I could set up a more elaborate user defined measure to account for this, but it seems like there might be a better/easier method for angular position measurement in mechanism?Thanks in advance.

I have a problem placing a UDF with a reference that is not contained in the parent part.Let's have a look at the following code, which is working as expected:   pfcAssembly_ptr assembly = pfcAssembly::cast(session->GetActiveModel());logFile << "assembly: " << assembly->GetFullName() << endl;   pfcSolid_ptr skeleton = assembly->GetSkeleton();logFile << "skeleton: " << skeleton->GetFullName() << endl;   pfcFeature_ptr partItem = assembly->ListFeaturesByType(false, pfcFEATTYPE_COMPONENT)->get(1);pfcModelDescriptor_ptr desc = pfcComponentFeat::cast(partItem)->GetModelDescr();pfcPart_ptr part = pfcPart::cast(session->GetModelFromDescr(desc));logFile << "part: " << part->GetFullName() << endl;   pfcModelItem_ptr sketchItem = part->GetItemByName(pfcITEM_FEATURE, "SKETCH");logFile << "sketchItem: " << sketchItem << endl;pfcSelection_ptr selection = pfcCreateModelItemSelect

CREO的config.pro可以通过session.SetConfigOption来更新， 比如一下工程图的配置也有类似的方法吗