Creo+ and Creo Parametric

When we do save a copy of existing model, there is trail history of the model. How to delete the trail history of the new model which we do save a copy?

Is it possible to use trail files for modeling. I was thinking to record some actions, some modeling, like select a specific publication in one part, and copy it to another active part. Then reuse that trail to my needed daily work.   Would it be possible? If yes how?

Hi,I am trying to define bearing constraint. I have base plate that is supported by two shafts at either ends. These shafts are supported by bearings so that plate can rotate around shaft axis.Please advise how should i apply bearing constraints to these shafts ?Thank you.

Hi, an issue here with calculated values in a drawing table (please see attached picture). Using more digits after the comma is not an option. If instead floor a ceil option is used the the wrong value goes correct, but the rest of the values for the total weight goes wrong. Is there a way to have all values correctly calculated. Thank you in advance.    

Folks   i need help modeling a drawstring bag in its relaxed and compressed position. I figured the top section can be modeled using trajpar or helical sweep. The bottom with surfaces and will connect together using merge, trim, etc. Would anyone share a cad model that resembles this thanks  

Creo 3, M070I'd like to use two conditions to filter a repeat region, can I do this?What I mean is that I want to filter all assemblies out of my region except the ones with the parameter BOM_DISPLAY set to YES.  So, I'd like to display assemblies only if these two conditions are met:&asm.mbr.type  == ASSEMBLY*&asm.mbr.bom_display  == yesBut, I believe that if I put those tow things in the repeat region filters the only items I'll get are those assemblies.  I'd like to get all the parts too (except skeletons and parts where BOM_DISPLAY is set to no).So, what I want is:&asm.mbr.type  != SKELETON*&asm.mbr.bom_display  != no&asm.mbr.type  != ASSEMBLY*EXCEPT where:&asm.mbr.type  == ASSEMBLY*AND:&asm.mbr.bom_display  == yesOf course, that's not going to work.   How can I accomplish all of this?

I have noticed that CREO 6.0.5 os released. Where I can find the improvement s made? Hope that PTC have worked a lot in stability.

HelloI have a question as catogory "how do this" i discover i can open a fille with drag and drop when i use a fille my working directory is my documents it is posible to set automaticaly working directory in same folder of that fille is?i suposse as modify a parameter in config.pro but witch?Thanks people

I have some simple parts that are used in a number of places.  In the Reference Viewer I see a lot of External References... Is there a way to remove or break these references? Thanks

I have an assembly that has several sub-assemblies that all have Pivot constraints.   When I try to drag one assembly it also wants to move the other... Is there an easy way to lock the other assembly so that only the one I selected will move?   Thanks

Somewhere buried in this assembly there is a constraint that is preventing the ability to drag a sub-assembly that was installed with a Pivot constraint.  Is there an easy way to find it?

Hello community,   I just made a simple form and saw that two sketches are still visible which normally shouldn´t be visible. I can hide them manually but I wondered why they are shown now (like said, normally they are hidden automatically) I made a composition between the sketch "RAND" and "BODEN". Boden is the inner sketch and rand is the outer sketch. I have enabled the material for better visualization. Attached you can find a photo.   Maybe someone can help me to adjust this error. Thanks in advance.  

Hi all together   I have the following problem and could not found something about:I have an STL-File (with facets) and need the position data of each point at each intersection. Ideally in the form of a text table. I do need that to compare the CAD values with the final values after the production.   I made a section, than right click to get a curve of the cross-section. Now I have the curve but does that help me? I have no more ideas and hope someone of you can help me?!   Best regardsPatrick

What does your company do to show MBD on assemblies?  How do you get away with not having assembly drawings?  Do you do any sort of "ballooning" or a bill of materials?  Or do you just assume that the downstream user can navigate their way thru CreoView to find the information they need within the parameters of each of the parts?

Hello, I´ve used the ProEdgeTessellationGet() method in my CreoToolkit App, but realized that I only get a few points as an output (22 points for a 180° 200mm arc). Is there any possibility to get a better tessellation of Arcs, etc. or to even set a distance between the  points of the output with the ProEdgeTessellationGet method? Thanks in advance

Hello! I would like to preface by saying that I have lurked through the community forums in hopes of finding a resolution to my specific situation, but I haven't seen something that applies.  I have however run into methods of Family Tables and Configurations, and "Model Properties > Flexible" edits -- none of which have resolved my case. I can't help but feel as though I am missing something rather obvious. Your patience is greatly appreciated! Attached you will have a very simplified example of the modeling I'm doing at this moment. --------------- I am modeling an FPCBA using vanilla Creo 5.0.*.  In this situation, I would like to have a configuration that pertains to the in-assembly geometry (Figure_A), and I would like to have a configuration that pertains to a 2D Drawing geometry (Figure_B). Currently, the default Master Rep defaults to Figure_C, which overlaps both configurations. Although the appearance of the model in Master Rep is undesirable, I can live wit

Unable to displaying screw thread size in cosmetic thread note. since this is limitation of Creo Parametric. I would like to request all users to vote on the requirement so that we have this improvement in coming version or datecode.   Thanks in advance!!!!

Hello   As we know, we can have dimension in drawing from part itself. All dimensions can be collected from solid by doing solid dimension visit for solid of drawing. Now, I am unable to recall visit API should be used to identify whether that solid dimension is visible in drawing or not.   I am having Creo 4.0 M070 toolkit license.   Something related to Displayed is there I guess, but that was deprecated and right now I dont have access to API

Hi, I have run into this issue before and haven't been able to find the setting to fix the issue. I have a workstation with a RTX2080TI NVIDIA graphics card running Creo 4. The surface in the attached image should show a single line drawing in the view in the upper right corner of the image.Anyone know how to fix this and what the config.pro settings should be?Thank you! Don

I'm trying to remove a part simplified rep but it says it's referenced by drawing I have in memory. I checked the drawing and removed all references to the rep. Every view I have references the master model and there are no erased views that may point to simplified rep. Am I stuck with this rep in the model? Any help would be appreciated.   Thanks  

I am trying to use the blank from one sheetmetal part to make a new part.  The goal is to have a reference link in Windchill between the two parts to help insure that both models will be considered when a change is needed to one.   I tried creating the new part from an inheritance feature of the current part.  I was able to create the inheritance and unbend all bends.  However, when adding the new bend, the bend feature fails when the bend crosses the boundary of the old bend.   Thanks, Kevin   Here are the models.

Hi Can we import NURBS surface from Rhino, convert to sheet metal for manufacturing? can split it into many smaller sheet metal? flatten? Attached rhino file:  

In CREO 5; How do you show annotations (e.g. axes) by drawing view for one component in an assembly?  There is a right-click option in the model tree to show dimensions by drawing view, but not annotations.  Thanks.

looking for some help i was busy making some changes in a part with the assembly open in the background. i don't know what happen, maybe a caught a keystroke, but my model fell over and the undo button would not undo whatever had happened. in creo how do you close a part and discard the changes from the assembly? effectively putting the assembly and part back to before the changes where even started.   thanks

I want to utilize an offset section that I created within my assembly but when I go to apply it within my drawing the option is greyed out. This seems like I'm missing something obvious here, is this a limitation of Creo? Is it because it's a 3d view and not a planar view or is it because i am using a shaded view? Any help would be much appreciated. Thank you