PTC Education

Hello,An error message appears in the third step when I install the license. I have the product number (BK400407EDSTUDENTUNICL).The error messsage is "Error processing the license. Please contact the PTC Licensing Department".Thank you for your help

The system envelope model includes the subsystems our robot requires, as well as, the size and position of each subsystem. The next step in the product development process is selecting the technology solutions that will allow the subsystems to perform their functions. Use brainstorming and research to begin developing ideas about how a robot could carry out each of the required functions.

A good design optimizes function or performance within a set of constraining factors. In the case of a robotics competition, the game description or challenge description will explain how your robot will score points or otherwise be evaluated.

As you go through the steps of the product development process, you will create organizational charts, data tables, 3D models, physical prototypes, test results, and instructional guides. This guide refers to these outputs as deliverables.

A top-down design strategy organizes the various challenges involved in building a successful robot into levels that each contain a specific set of parts and important geometric or performance information.

This document defines the four phases of the product development process.

When I enter product code (BK400407EDSTUDENTUNICL) in the installation it gives me an error message. Hovering over the message says "error in license processing please contact ptc license management". And yes I have tried entering the product code manually rather than copying/pasting and it stills gives the error message. And under license summary there are no sources listed. I need this program ASAP, please help!

I have been trying to istall CReo 3.0, but I haven't been able to do it. The instalation always get's stuck where in the Aplication Selection part. There is a meesage that sasy please wait while we retrieve your license and it gever goes beyond that. Thank you for your help

Hello I am trying to build a robot for FTC and need some CAD files. In specific Actobotics files, but i need them in the .prt or creo file format. I did find some but they are in .STEP format. They do work, but not very well. This makes constraing and assembling hard. Any files or sites would help. Thanks

I am new to PTC.  We just bought a hobby cnc router.  What options (educational free) are there for making a part and then milling it?

I have recently gotten a new laptop which is 64-bit, as opposed to the 32-bit computer I had before. When I tried to move the Mathcad 14 student edition that I already have by installing it from the CD, it didn't work. Now I'm worried that it isn't going to work because of the 64-bit operating system.I just went through the service interface to request a new license, although I'm not sure that's the issue. Apparently there is no way I can call "customer service" to ask about this, which is very annoying.

Hello,i´m attending the University of applied sciences in Augsburg. I need the Student Version of Creo 3.0  immediately. I downloaded the Windowas 64bit file and started the setup. I typed in the Code and all is well but when i´m asked for my account data and i type in my Name and Password it isnt´t working at all.I always get that email:Dear User, Thank you for your interest in the PTC Creo 2.0 Student Edition. Attached is a backup copy of the license file that was downloaded during the initial installation of Creo 2.0. The installation can only have completed if the file was successfully downloaded and this file is intended only as a backup. If desired this file can be saved in your email or to a folder on the C: drive such as C:\ptc on the machine that you have installed Creo 2.0 to be used if the original file is lost or deleted. If you have received this license file after requesting it manually from the PTC website or if the Creo 2.0 software must be reinstalled this copy of

Hi,I have a problem with license identification. Is my product code incorrect BK400407EDSTUDENTUNICL, please advise.

‌I have creo 3.0 on my PC and would now like to install the program on my laptop, however, the installation always aborts when verifying the data.Can you install the program on one device?

Hi guys, I'm Junior at Pusan National University in South Korea.I usually use PTC CREO 3.0 while working with my major, Mechanical Engineering. But Recently I CANNOT access PTC.Because of this error,License request failed for featureRequesting CREOPMA_Student3 ...C:...._license.dat:(-10) Feature has expired........................It means that I cannot use PTC or any other errors? Thank you already for your favor

I used the code provided in http://apps.ptc.com/schools/references/install_creo3_unistudent_standard.pdf?_ga=1.44004205.991619151.1478220157 and when i click accept i log in my account, and i get an error, i tried contacting tech support but i havent got a reply from them.

HI! I have an issue with the License Identification on Creo... When I entered the product code which I got from the installation instructions, the computer responded me with an "Error" instead of "Success" as it was supposed to do. Do you know how what the problem may be, so that I can proceed with the installation?

I still have trouble connecting a simpleClient from Java SDK to our new ThingWorx instance.Please see the debug info attached.A different precompiled Client (AcademicEdgeConnector by M Cheli ) can connect successfully and push data to the platform form the same client machine (i.d my laptop).

Hi, I'm trying to install Creo 3 Academic but I'm not able to enter the product code. I tried to run as administrator and turning off the firewall but nothing helped. As you can see in the screenshot the field for the Product key is disabled.

Hi allI've just downloaded (for £185ish) the student premium version of Creo 3.0, but it doesn't seem to offer either the NC milling or injection moulding processes that I actually need for uni. I'm curious if it's maybe just an error I've made during installation or if it actually doesn't offer 80% of the functionality that students need?Thanks for any help...Calum

Every time I go to run Creo Parametric 3.0 these windows pop up and selecting any options shuts the program down immediately. Does any one know how to fix this?