Creo+ and Creo Parametric

I am trying to enable ModelCheck Gatekeeper to prevent check-in of models if they do not contain proper parameters and values. When I do a check-in, I get the following error messages: Incorrect ModelCHECK mode used on models in the context Incorrect set of config files used on ModelCHECK in the context Model has not been validated in last 24 hours in the context ModelCHECK failed on models in the context   Running ModelCHECK interactively, I get no errors or warnings. Creo7.0.5.0 with Windchill 11.1 M020 CPS20

I am using Creo Parametric - Release 6.0 (connected) 6.0 6.0.2.0Need to output the coolant/on after move to clearance plane.The output of coolant/on is come after tool change. Need to move the coolant/on after start point.How can we move this coolant/on line? Thank you.

I am using Creo Parametric 3.0 M120CREO 2D不显示或部分显示   "The projection of creo two-dimensional map is not displayed, and the parts are not displayed completely" Translated with Google Translate. Translated by Iuliana Nuta, 01.Nov.2021

Hello friends ,I have collected solid edges from drawing view , but edges collected from view is all edges available in solid , but I have to collect only visible edges in view , for that I use ProDrawingedgeDisplay() API , it gives same result for all edges available in solid , Please help me to resolve the issue 

Hello friends ,I have calculated the angle  using Measure API, but I have to round off value , Is there any API available in toolkit to round off the value . Please help me to resolve the issue. 

Using CP4.   TL/DR: You can use an interchange assembly to swap out un-related components of an assembly.  You can't (?) use it to make the same swap in a merged part.   Example A is a weldment.  I have 2 different versions.  A.ASM for the drawing and A.PRT that has all the components merged together.  A has tabulations (i.e. A-1, A-2, A-3, etc.).  The tabulations can use either components B or C.  B and C are similar, but they were created in different files.   Assembly Component A-1 B-1 A-2 B-2 A-3 C-1 A-4 C-2   Working A.ASM (generic) uses B.PRT (generic).   I made A_INTERCHANGE.ASM with the Interchange sub-type to define reference pairs between parts B.PRT and C.PRT.   A.ASM family table has a column for model B.  For A's instances, it calls out the instances for B.PRT or C.PRT as per above.  The family table verifies successfully.  I've spot-checked several of A's instances and confirmed that

Hi everyone! first post here. Recently we got a PocketNC V2-50 in our warehouse and I'm trying to set up a PostProcessor for it. I'm almost there, but for some reason when the tool is moving around the spheric surface, it is not exporting the G-Code as it should be. To me, it looks like the Post-Processor is trying to get from the beginning of one of the dome paths to the end of it but instead of going from the point, let say, M to point N as it should, it is getting to N from behind, so it's trying to calculate a smooth curve to get there, resulting in a wrong trajectory.(Image below)The cylindrical section is "fine", and I quote it because the whole program is running with the pocket NC is executing the code with the A table rotated 180º, which doesn't make any sense unless there's a setting that I'm missing in the Option File Generator (which is where I've been trying to get it done) The PostProcessor I'm using as a reference is the UNCX01.P37, which is one of the Cre

Hi,Creo User PC visual & Creo view adapters visual , both are in the attachment.Because of this difference, user's thumbnail (Creoview visuals) and Creo visuall are different.Please advise me on how to avoid that unwanted object in the adapter? How to hide and  

hi @all, we're trying to create an unattended installation package for creo 7.0.4.0,but after it run on first installation without problems, on second run setup.exe it brings return code -609 (although it was uninstalled before properly) do you need further informations and which?machines are windows 10 1909. thanks and regardsDom 

I received drawing formats from a client where the numbers and letters around the drawing sheet appear when you first start the drawings but disappear after it has been saved. This is also the case with some title block parameters. I am using Creo 4.0. If you know how to fix this, that would be greatly appreciated.  

I am using Creo Parametric 3.0 M170Unable to access PTC Learning connector.Here are the errors that I faced,learning connector is unavailable

I am using Creo Parametric - Release 4.0 (connected) 4.0 M120Crashes when opening partHere are the errors that I faced EXCEPTION_ACCESS_VIOLATIONCan someone figure out what caused the problem from the traceback file? It only happens with this one file.Traceback: ----The trace creation timestamp is: Thu Sep 23 15:54:16 21The executable build timestamp is: Thu Jan 09 01:39:12 20The datecode is: 2019444The pro machine type is: x86e_win64The process ID is: 15552The traceback type is : CRASHThe logger exit status is: 00003The Trail is: 0The release is: 4.0The external datecode is: M120The product title is: Creo Render Studio-------------------------------------------------Exception EXCEPTION_ACCESS_VIOLATION has occurred in the thread 10008.Main Thread 10008=====================0x00007FF786523ECE NULL (NULL:0) (xtop:0x00007FF780010000) ( 0x0, 0x0, 0x127b5290, 0x3d14e68f ) 0x00007FF786505AA9 NULL (NULL:0) (xtop:0x00007FF780010000) ( 0xb06fa30, 0x7fa263f0, 0xb8060e0, 0x14253508 ) 0x00007FF786

Dear PTC Community, I have tried for quite a while but do not seem to figure out how to make the following possible: I have created a part in which I defined the geometry I would (later) like to substract from a simple extrude feature to make a gear. The geometry is a parametric build of surfaces that I merged and patternd. See below:I now created an extrude feature of which I would like to subtract the previously created geometry to make it a gear. Sounds like a simple task but I am completely stuck and can't seem to figure it out. Happy for any input.I was able to "Solidify - remove" one small section from the extrude before the pattern but once I have the pattern it will not let me Solidify it OR once it is Solidified it will not allow the pattern. Using Creo 2.0.  Best Regards,Rene Rudolf

Hi,I'd like to have a G3-curve, which uses points as references. In sketch, spline has no option for G3. Using the Style Tool I can create G3 curves, but can't reference them. Is there an option I haven't found? I would be grateful for any help. Thanks!

Hi everybody, My computer have Intel I7 processor  8th gen, 32gb ram, ssd and Nvidia RTX 2060 8gb, but I have some problems and errors.Do you think it's because of the graphics card ?I must change my graphics card? There is a configuration that I missed ? or Just update the card drivers?

Hello Community, is there a setting or method to reduce the vector resolution when exporting a line view from Creo View to a vector file, e.g. to PDF? With some assemblies, we get 2D vector graphics with hundreds of thousands of lines (or points), which are then difficult to process further in our vector graphics program. Thanks for ideas

I am using Creo Simulate 7.0.0.0I recently upgraded to Creo 8 and now when I try to open part files created in Creo 8 in Creo Simulate 7 I get a message that the file "cannot be retrieved". I suspect this is a backwards compatibility issue but how can I work around this until Creo Simulate 8 comes out?Here are the errors that I faced[file] cannot be retrieved

I am using Creo Parametric - Release 3.0 (connected) 3.0 M170Using the blend feature to create a oblique cylinder that has rolled and bend sections, software cannot unfold the bend walls.Here are the errors that I facednone

I am using Creo Parametric 8.0 8.0.1.0Installation Assistant for Creo 8.0.1.0 (setup.exe) won't run on Windows 10 Build 21H1. The error is " This app can't run on your PC - to find a version for your PC, check with the software publisher"Here are the errors that I facedThis app can't run on your PC - to find a version for your PC, check with the software publisherIt ran normally on previous versions of Windows 10.

Hi, when i used Inventor for modelling and drawings, the line thickness was set up for every kind of lines. Like outline was thicker than hidden lines or center lines. When i opened those exported dwg files in AutoCAD i could click on "show/hide line thickness" and outlines "poped up" from the drawing. Now - when i export drawings in Creo, all lines are same - hidden, outllines, center....How to set it up for all drawings? I mean - it should know what is model outline and what is just hidden line, right?   I hope you understood everything (my english is not so good as i want)

 The drill web cycle works properly through creo when playing the toolpath, but when it posts out it does not work.I see that the web drill sequence outputs a CYCLE/THRU in the CLDATA, and according to the GPOST literature, if your control does not have a hardware cycle for CYCLE/THRU (ours doesn't) and set it to NA, then it will force GPOST into software mode.  The issue is, it seems that GPOST even in software, deals with CYCLE/THRU differently than Creo does.Does anyone have any ideas on how to get this to work correctly, or possibly even have a working FIL for reference?

Hello community,I'm running a very old MELS on a VM (Win7, 32bit) for an also old version of ME10 8.7The VM runs only for the MELS and the software is getting older and older and I want to install it directly on my server (Win2012R2, 64bit)Sadly the old setup cannot run under this new OS. Has anyone an idea where I can find a MELS-setup which can run under 64bit?I searched, but found nothing... 😞 regards

Hello everyone,Does anyone know how to export a prt or drawing to dxf using VBA Excel? I got other activities such as changing dimensions and creating a drawing, but this one is having difficulty.

Need help to convert thousands of mi files to dxf.I have tried dwgdxf tool. Success rate is near 50%. This toll can only read mi 2.5-3.5. Creo parametric can import all the mi files individually and successfully export to DXF. Couldn't import by batch in CREO parametric. Can anyone suggest me a good working method? 

I have a really weird bug that maybe someone can help me with.  I have been using ProE since ProE2001, so I know the program well.  but I haven't seen this before.On sheet 1 of my drawing, the BOM table appears to be missing my second part in my assembly.  But when I click on the table cell, the data is still there.  It comes back once I right click each one, and middle click to accept.  If I change sheets and come back, second part row goes blank again.  If I print or save to PDF, the tables print empty.  Same thing happens with the drawing block on Sheet 2.  Except it's true for the entire title block.  Every single cell in the block is empty, unless I click and accept each one.    If I change sheets and come back, it goes blank again.  If I print or save to PDF, the tables print empty unless the text appears on the screen.HELP please.... anyone know what's going on and how to fix it?-Fong