Mathcad

So Mathcad Prime 6 has a new symbolic engine.   There's no indication within the product what the symbolic engine is. However, if you poke around in the installation directory, there's a new folder called Axiom with an executable for the computer algebra system called FriCAS somwhere inside.   So I guess the new symbolic engine is based on this: https://en.wikipedia.org/wiki/FriCAS https://en.wikipedia.org/wiki/Axiom_(computer_algebra_system)   [edited to include reference to FRICAS]

  I am trying to use Given-Find to solve for 2 unknows.  Mathcad gives error saying this variable is undefined.  Please see Mathcad attached.  Wondered how to fix this.  Mathcad is attached.

Во вложении можно найти следующие справочные материалы для Mathcad Prime 6.0:   ▪ Прочтите это сначала,  ▪ Руководство по установке и администрированию,    ▪ Сочетания клавиш,  ▪ Что нового.

In the attachment you can find the following reference documents for Mathcad Prime 6.0:   ▪ Datasheet,  ▪ Installation and Administration Guide,  ▪ Keyboard Shortcuts,  ▪ Licensing Instructions,   ▪ Platform Support,  ▪ Read This First  ▪ What's New.

Hello everybody,does someone have news about MathCad Prime 6?Some timesheet?MCP5 has introduced too few improvements so I think PTC intends release new version soon. Or not?...ThanksBye

Good Day. I need your help with the following equation. I cannot get a solution for β. In the problem statement it mentions that α in degrees is 43.2 which in radians is 43.2/57.3 = 0.75. Then, the problem mentions that β = L/R (inductance divided by resistance), with R = 10 ohm, and Vm (maximum value of sine) is 120Vrms * √2 = 169.7Vpeak. When I substitute these values in, and try to solve for β I get an undefined solution (see attached worksheet). Please help me find what am I doing wrong. Thank you.

I randomly throw (1000 times! Keep a patience!) five points into a square and draw a second-order curve through them.These are seven curves:- a hyperbola (we can see one or two branches) and an ellipse (full or a part of it) - two usual cases;- a parabola, a circle, two intersecting lines, two parallel straight lines and one straight line - five rare cases! But the Seven is a fine number!Who will see all seven possible curves, must have good health, happiness and prosperity in the new 2018 year!   Physical Mathematics

why it does not work??   can you help me?

I have a date in two columns, but i have to do filtering or conditions to select only date (x and y) which are inside rectangle. , , ,    

みなさん、こんにちは    再び共振周波数についての質問です。 添付ファイルを確認してください。   1. w2bとw4bの正しい周波数が見つからないのはなぜですか？   2. w2x（w2y）とw2a（w2c）は等しくありませんが、正しいですか？   また、w4x（w4y）およびw4a（w4c）。   3. R2 = 1mohm（1ohmではない）の場合、上記の2つの周波数は等しくなります。  さらに、それぞれw2とw4に等しくなります。  R1でこれが異なるのはなぜですか？   4.共振周波数は一般的に次のうちどれですか？   （1）最大/最小インピーダンス   （2）虚数部= 0（引数= 0）   これらのうち、3と4はMATHCADに関する質問ではありませんが、誰もが知っている場合はお知らせください。  

Hi, can anyone help me to convert my xmcd file to excel file? I know that i have to convert it to mcdx first, but after that i can't covert it to excel file.   Thanks a lot!

Can you show me one formula for this points? The Mathcad 15 sheet is in attach! Thank you!

can someone convert this file. Need to read the formulas inside this file.   Just installed mathcad with 30 day licens.   Thanks    

I do not know why... please...

Hello everyone   I want to get the resonace frequency by L-C-R series circuit.   I tried 5 method. Please see attached file. But I can not get the correct frequency by No.2,3,4,5 in this file.   Please explain...  

Hello.  Is it possible that it does not make a diagonal line when converting to pdf ? 

    what is the difference between xq and xf

o     answer was supposed to 0.274 and 0.052

  Do i have to use y1 when i sove ode or not?

could you help me?

Do you know it?

I am attempting to complete a comparison using values from a table and am getting a scalar value error. What do I need to do in order to get a column of values out of the attached.     

I have just renewed my license for Prime 5.0 and when I looked for updates saw that Prime 6.0 is due out September 15, 2019. Does anyone have any info on if this will happen?

Hi, A friend asked me for a phase diagram of a transfer function (see photo and file). I distractedly used the arg(Im(W (iω))/Re(W(iω))) operator for the phase graph. I know this is an old problem, this graph was actually incorrect as seen from the comparison with the correct graph of the function φ1. Why does this happen?