Creo+ and Creo Parametric

Hello Team, I am trying to add gravity load along with other applicable forces. Without adding gravity load, simulation goes fine but when i apply gravity load, it fails. It shows below error: Can you please suggest what could be the reason for this? I am really under pressure to finish the simulation. Any help will be really appretiated.The design study terminated abnormally.The nonlinear iteration did not converge for thetime value:   3.90625e-03  o The model may have a buckling mode with a load factor    smaller than this value. You may determine the smallest    (linear) buckling load factor by running a buckling    analysis.  o The deformations may be large enough that you must    further refine the mesh. To locate potential problem    areas, it may help to run an analysis with reduced    loads and examine the deformed shape of the model.  o The model may have a static instability. 

Pro's hole command does not provide for BSPP threads. how to activate BSPP threads

Hi All, I have a student license and from past 2 days i get the below error in sketcher mode when i try to update the dimensions. It doesn't allow to modify any of the dimensions in sketcher mode.  "When a constraint is active, right click to cycle through lock/disable/enable the constraint. Use Tab key to toggle active constraint. Press and hold Shift to disable snapping to new constraints." Kindly support as i am unable to work.  Thank you.

CREO 7.0.6.0We are having an issue where we double click on a dimension while in sketch to edit and the dimension box is closing out before we can edit the value (see attached video). Has anyone seen this before? Any help would be greatly appreciated.(view in My Videos)

Does anyone have any recommendations for default combo states? Below are PTC's:   I *think* there are some recommendations in this book as well and we are considering getting it. If anyone has read it I would appreciate feedback. https://www.amazon.com/Re-Use-Your-CAD-Model-Based-Handbook/dp/B08X65PK6W If anyone has any other recommendations I would appreciate that as well.

Hi, Creo-8I would like to get sheet metal part with different thickness after forming ( coining ) operation like the attached image below. Any idea  

Greetings everyone, Allow me to introduce myself to this vibrant community! My name is Amitabh Mukherjee, and I'm thrilled to be a part of this group. With an extensive background in multi-CAD customization spanning across various platforms like NXOpen, CATIA V5 .NET, CAA V5, Inventor, and SolidWorks API, I've recently embarked on a new journey diving into Creo Customization using Object Toolkit (C++) with Creo 10.0.As I delve deeper into this exciting realm, I need some guidance and insights from the community members here. Here are a few areas where I could use a helping hand: Navigating the Creo API Object Model: I'm eager to explore the vast landscape of Creo's API object model. Could someone point me in the direction of resources where I can browse through the hierarchy of classes, and interfaces, and understand their relationships such as base classes and derived classes?Creating PMIs with Precision: One particular task I'm currently grappling with involves creating Pro

I am using Creo Parametric Release 8.0 and Datecode8.0.3.0I would like to know if there is a way to extend the left hand side section of the browser window to maximum extent possible. We are not going to use the section with address bar. We would like the right hand side section to be as minimum as possible.I tried setting Navigation Window Width to 100% but it didn't work. Browser width as percentage of main window is greyed out with 82 as its value.Here are the browser related variables set in the config fileweb_browser_homepage about:blankweb_browser_in_separate_window yes

Hi, I need to create a list similar to the BOM but with the asm welds. I need the weld information (SEQ_ID, TYPE) and I need the welding process intervals linked to that weld. I have some parameters in the weld process but i dont know how acess this parameters in the drw. I add some photos. Using the example of the photos iset the weld process 3, in the weld process have parameters about current, tension and gas. So i need a table like this: SEQ_ID   TYPE      WELD_PROCESS   CURRET(A)    TENSION(V)     GAS1               FILLET   PROG3                     230                  26                      CO22              FILLET   PROG2          &

Suddenly creo fails to create PDF using quick export or manual export configuration. upon clicking either QUICK EXPORT or EXPORT to create a .pdf, nothing happens. no error or warning. just nothing. 

Hi, I am working on this surface that is part of an assembly. When I try to merge the quilts after the mirroring (in FRONT plane) i get an error of overlapping. I am struggling to find the overlap/how to resolve this issue. My files are linked (assembly, reinforcement plate and upperhood). The reinforcement plate is using the same geometry as the upperhood. The issue occurs in the part called: reinforcement plate. Any help is appreciated.  I am using the student version of creo parametric.   

Hello, we're looking into integrating with Soldiworks PDM and was told we need the API Toolkit. Searching around I found different versions ranging from free to paid and in different languages. Has anyone gone through an integration like this and know if the free version of the Toolkit is suitable or do we need to purchase.   Thank you in advance!

“Her favourite show used to be Friends, and growing up she could hear it and she could read the captions, and it was so exciting for her that she could get that moment back.”   In the modern world we have an abundance of technology that helps us with our communication, information gathering and entertainment needs. But most of this is inaccessible for DeafBlind individuals whose primary language is tactile sign. It can be difficult for them to access news headlines, or to even find out what the weather will be like later on in the day.    Tatum Robotics is advancing accessibility by developing a robot hand that can communicate with DeafBlind people through tactile sign and allow them to access the internet. Designed to allow for as much movement as possible, the T1 Fingerspelling Hand features 18 degrees of freedom whilst still feeling as much as possible like holding a real human hand. DeafBlind people’s main source of communication is usually through human interprete

“What the water rig is at its core is a mobile water treatment technology, and it dramatically changed the lives of the people living on that site.”   Having clean, drinkable water is essential for everyone, no matter where they are. For some on-site workers on remote oil and gas drilling sites, this means transporting in large amounts of bottled water. The result is a large amount of plastic waste from the bottles and air pollution from the extra traffic.   WaterFleet provides an alternative solution. Their water treatment technology means that a mobile rig can be hooked up to an existing well or water storage source on site and provide people with clean potable water on tap. As the rig processes the water, it automatically and continually monitors the quality to ensure it’s safe. WaterFleet also uses this technology to provide temporary water solutions to areas that have been affected by natural disasters.   Our producer Eva Ruth went to the WaterFleet headquarters i

Check out this video on Creo Sketcher from PTC Application Engineers. Presenters:  Emily Pinto (Solution Consultant), Lino Tozzi (Technical Specialist, Fellow) & Tom Quaglia (Creo Segment Sales).  

Check out this video on Creo "Sketcher" from PTC Application EngineersPresenters: Emily Pinto (Solution Consultant) and Ryan Butcher (Solution Consultant, Fellow)Original Date Presented: March 19, 2024 To dive deeper into the subject, check out Creo "Sketcher".  

Does anyone know how to set symbol_font to legacy by default for new parts and assemblies? I have tried changing it in my config files but I can't get it to work.   The issue is, that unless both the assembly and or part file and the drawing file have symbol_font set to legacy, this strange offset happens to my diameter symbol:

I am using Creo Parametric Release 9.0 and Datecode9.0.4.0I am attempting to open files from the 1990s that are labeled as DRW and I cannot open them.Here are the errors that I faced'Filename' Cannot Be Pulled

I have a part model that is solid geometry. When exporting the part using STEP it generates the file but the STEP file does not contain any geometry when imported.   The part does not have any geometry checks and has absolute accuracy (1E-4 inches) set in Creo 7.07. The geometry is not what I would call complex.   I have been able to get around this issue by saving the part as a Creo neutral file, opening it as a part and then exporting it as STEP. This process yields accurate geometry in the STEP export.   The source part file will not export to STL either but there is no diagnostic info on bad geometry. Typically this would identify are where tessellation failed.   Has anyone else encountered this issue?    

Hi, guys. I'm working on the surface using the table pattern function in Creo Parametric 10.0.0.0 and an error occurred in this process.Excel fetched the location, length of the feature, and thickness data to extract and patterned, but some features encountered problems and the extrude did not proceed. After proceeding with the other random data again, I confirmed that the extrude was completed without any problems. Can I get any help with this?I attached the Creo file, Excel data, and config.pro file into .zip file. The size of the blocks is 51.5625 x 51.5625 x 4 in the order of x, y, and z [All length units are mm] Among the green parts of the image, except for the outer edge, the part that appears inside is the part where the error occurred.Sheet1 data was used in the Excel file, and it means the length of the feature from column A to the location where the extraction operation starts, the x-axis, y-axis distance, and the thickness to proceed with the extraction opera

I have an assembly with a few sub-assemblies. Each of those subassemblies are set to be of specific rep in the main assembly  (some are at Master, some are "User specified")  When working with the main assembly, when I right-click on one of those subassemblies in the model tree, and click on the pop-up menu "Open" - it brings a little window with the available reps, and I have to choose the rep that I want to open that sub-assembly in. I am hoping to find a way to open the _current_ rep by default. That is, if (from a model tree) I click "Open" on a subassembly which is set to be Master - that subassembly opens in its own window at Master rep. If I open another subassembly from a model tree of a custom rep "No Fasteners" then Creo loads that sub-assy activating the "No Fasteners" rep. There is remotely similar setting "open_simplified_rep_by_default" but it does a different thing. I am looking for something like "open_assembly_tree_component_in_current_rep". I

Hi, My goal is to clearly have the presence of external references in the part visible by having "Dependency status" column in the model tree. This way if i create an external reference in the part, this column would have "Dependent" written on it.  However, I noticed that if I create a new simplified rep in the part, then it automatically shows as "Dependent" in the "Dependency status" column. What is even more interesting - when I activate the Master rep, the "Dependent" status goes away; when I activate my new rep again - the "Dependent" comes back.  As per this article here: https://www.ptc.com/en/support/article/CS67430 , the "Dependency" is always external. This makes me think that this may be not intended software behaviour, because I am creating a rep within the same part, and not initiating any external dependency. Could somebody please comment on why this is happening, and potentially how to create a custom rep in a part without having

Hi everyone, I have an issue regarding "plot_drw_to_pdf.ttd" in CREO Distributed Batch.Can someone please tell my the correct syntax for "STROKE NON TRUETYPE FONTS" in the TTD file?The default value for Font is:<font enum="PRO_PDF_USE_TRUETYPE_FONTS"/> I've tried various configurations like:<font enum="PRO_PDF_STROKE_NON_TRUETYPE_FONTS"/>or<font enum="PRO_PDF_STROKE_NON-TRUETYPE_FONTS"/>or<font enum="PRO_PDF_STROKE_NONTRUETYPE_FONTS"/>or<font enum="PRO_PDF_STROKE_NON_TTF"/> nothing worked.

As per the original post.    I am having a similar issue trying to install PROEStudent wildfire 3.0. The DAT file sent to me is not recognized by the install program as a license file.

So we upgraded from Creo 7 to 10. When we did, this annoying thing started occurring where this information window would pop up upon every regen. After a couple of days, it stopped doing it. But today it started doing it again randomly. I've tried turning off all notifications and changed the notification behavior to "Do Not Show", but it still pops up. Having to click the X icon every time I regen the CAD model is GREATLY reducing my ability to work... I don't mind having the little banner show errors and dissolving after a little on it's own, but having to acknowledge every pop-up during design is obnoxious and pretty much makes the CAD software unusable...