Creo Modeling Questions

How to change default depth value IN Extrude...

Hello,I am new to the Hole table functionality. Could someone please guide me to the document on the same?I would also like to understand different options available on GUI and use of the same.RegardsKetan

                                                                                                             

Years ago I downloaded various Mil Spec Hardware zip files from the PTC website. (EG...ms24693-8.zip) Was checking to get updated files, and cannot find where on the site to download these files. I re-downloaded the Basic Library, and they arent in there.Any help would be appreciated.Thanks!

Hello,2 questions regarding configurable structures in CreoParam:1- Is it possible to assemble a configurable module within another configurable module ? It looks not, but maybe it's a setting to change ?2- Is it possible to configure options to select more than one variant at the same time ? I mean in my product I can have several variant for a module. They are complementary.thanks

Hintergrund:Das Problem beim Befehl Zeichnung zuordnen ist, dass das Modell welches die Zeichnung zugeordnet wird, in der gleichen Ausrichtung modelliert sein, muss wie das Originalteil. Unter der Voraussetzung, dass beide Modelle ähnlich sind, bekommt man auch anschließend ein gutes Ergebnis. D.h. nur geringe Nacharbeit.Beim Befehl Zeichnung aus Vorlage erstellen ist man in der Lage die Richtungen neu zu definieren. Die Möglichkeit die Richtungen am neuen Besitzer zu definieren fehlt beim Befehl Zeichnung zuordnen.Vorteil:Das Bemassen einer Zeichnung hat einen großen Anteil am Zeitaufwand in der Zeichnungserstellung.

As per our day-to-day work we use have one space in View note. As per the Creo std_ansi the View note shows two space. Why there is no numerical value is provided in the Creo to change the View note space as default one space.Rajesh

Hello All, Another question. I have setup two bevel gears I can get them to run, and also in the right direction. However I cannot get them to go at the same speed without applying a servo motor to both gears. Is there some way around this to only apply one servo motor, or are two servos a must? Thanks in advance for the help.

Hello All,I am setting up this gear differential for a class using bevel gears. I can get it to run properly, however if you look at this picture the gear on the right side and the bottom gear are colliding. How do I overcome this. This is a manufacture model and I have been using the helix and pressure angles listed by the manufacturer as well as the pitch listed. Any help would be greatly appreciated. Thanks.

как автоматически подгрузить все модели таблицы семейств в чертеж

@

Anyone willing to spend a few minutes on the phone talking about data managing SW files with me?I have tried my SW VAR and didn't get to far. I need someone versed in both systems so we can talk contrast and comparison between the two systems.I am knee deep in the transition from prototype to production, making changes to SW files with the same name, on the same computer, that is (untimately) controlled by Windchill. I had an umwanted cross pollenation of files today and I need to correct it before moving too far forward. "Select Working Folder" is the greatest thing EVER! Those in the know will get the joke.Thanks for any help you guys and girls may lend.

The company I work for is upgrading to Creo 2 in the next few weeks, I am supposed to learn animation using creo2. Do I need a specific add on to perform animation?thanks in advance for any input.

Hello All,I have been having this problem for quite a while now. While using planer section option I am not able to see the section of the model. However the 2D section can be seen in the separate window but the model is not updated. I am adding a snapshot so that you understand the problem more clearly. You can see I have moved the plane by 100 units but the model is not changed.Please if anyone could help me on this.Regards,Shashi

BonjourFaut il de nouveaux codes licences pour passer de CREO2.0 à CREO3.0?

Hi alls, What would be a good notebook computer for :- Using Creo occasionally, for viewing purposes essentially.- Most current usage would be MS Office.- Lightweight for traveling but with a big screen (touch screen ifpossible).- About 1000$ max... I have a little HP tablet PC with 2 graphic cards and it's works fine withCreo but HDD is about dead ;-(I think it's time to change 😉 Thanks for any (good or not) experiences or advices.GB

Folks,I created some constraints and I am struggling to get the correct results, or should I say what I think should be the correct result.As you can see above, I created a rigid link between the Pin, Bushes and the Arm. I really wanted to create a pin but for some reason I could not get the results correct either.What I was expecting to see was some load going thru the pin, but I don't see any?Any ideas or help ? much appreciated.CheersChris

[cid:image002.jpg@01D06AD3.2E69E540]

One of our Product is giving this error when you try to add objects to a project.[cid:image001.png@01D067C7.DE2E3F30]I can add objects from a different Product to the project. So it's nothing to do with the project.What permissions would cause this? Every user we have tried is getting the same error, even admin's.David HaighPhone: 925-424-3931Fax: 925-423-7496Lawrence Livermore National Lab7000 East Ave, L-362Livermore, CA 94550

Hello everyone. I'm a student of mechanical engineering novice. I was assigned a project for a boxer engine 150 Hp but i have no idea of how it should be done. I was advised by my professor to look at some project of bmw engine or rotax 912 but i can't find anything. Could you help me and show me how i have to proceed? Thanks very much

Has any seen this error? "A problem has been encountered with the browser. Please restart application to access the browser again." Only some users get this error some of the time. Anyone know what may be causing it?Using Creo 2.0 M130 and PDMLink 10.2 M020

Creo Parametric 2.0, M130:If you delete a "SEE DETAIL A" note, is there any way to get it back?I don't see it in the "Show Model Annotations" dialog. I tried selecting the detail A view, then right-clicked, picked Add arrows - selected the section view. No success.I tried redefining the reference point, the boundary, the boundary type - no success.In older versions I could show all notes to get it back -- which had its own problems but at least I could get it back.Yesterday I ended up creating a new detail view, but goodness that's the hard way around. There has to be a better way.Thanks!Kind regards,Janet Grove

Are there any documents out there to show us what to do with the changes that where made? Dimensioning should not be this hard?

hi,how could i close annotation element display when i start pro-e?

Hallo zusammen,ich versuche hier eine Hohlkehle (Ausgleichsradius) zu erzeugen, aberdie Funktion will and dieser Stelle einfach nicht funktionieren.Da der Es... meist vor dem Rechner sitzt, bitte ich einmal zu prüfen, weshalb das nicht funktioniert.Ich benutze nach wie vor die Version 4.0 kann aber auch Daten von 6.0 einlesen.Hier also die Daten als Bild und als Datei.Mit GrußWerner