Mathcad

Can I update to Mathcad ver. 6.7 with this current license?

Hello to the whole community !!!What to do to get the correct answer? Thank you in advance, who will answer.

I do not use symbolic evaluation very often so I am sure I am doing something wrong.  The following expression should equal mu_0 . Why do I keep getting the same thing back? Do I need a different keyword (I tried several)  or a modifier?     

Installation issue with Mathcad 15. Received an "unexpected error" message - The server comitted a protocol violation. Section=ResponseHeader Detail=CR must be followed by LF

Требует лицензию и не могу запустить, помогите

para cálculos estadísticos

please anyone help me, ive been working this mathcad all night and suddenly this file corrupted. please anyone help mee. the deadline is near:(( helpp

I'm subtracting 2 temperatures. But Mathcad gives an unexpected answer: ΔT should equal 280°F.  

I try to replicate the example from  Example: Polynomial Interpolation (ptc.com) How Ian I plot the red error bars?

I have an array, and I need to create another array, and calculate the successive average of the numbers as I move along the first array. For instance, the average of 1st & 2nd, then the average of 1st,2nd, and 3rd, etc. till end of the array   Below some more explanation, including my attempt, but I could not reach what I am looking for. I appreciate your help... Thanks    

Hi everyone, When I want to put a variable in an Excel-file, but with non standard units, for example mm instead of meters, I simply divide it in the input field (see example).  But what about a temperature? I have tried different ways but without success. It always comes out as Kelvin.  I would like Celsius °C.   Basically the question is: how do I "adimensionalize" a temperature, that is reduce the value of temperature to a simple number, without units?   Thanks a lot in advance Best regards Claudio

Ich musste mein PC zurücksetzen.Dabei wurde das Programm gelöscht.Jetzt möchte ich das Programm wieder installieren

I´ve reset my pc

I am struggling with how the Combobox works and its capabilities.I created two combo boxes, and I could populate some variables using the first combo box, but I also need to be able to change the results based on a selection from the second combo boxHow can I do that?Attached is the Mathcad sheet in prime 7

When I use new conversion tool to convert from earlier versions to Mathcad Prime 7, the new worksheet has a lot of markinging in red saying the format has changed, and a lot or red arrows. I am ok with the format changes, and I do not want these error messages or the red arrows to be on the new worksheet, How can i get rid of them, or accept them, perhaps they will go away that way. Thank you

I am using Mathcad Prime 7.0 7.0.0.0A Mathcad v15 converted to Mathcad Prime 7.0 has the last page empty but I am not able to remove it. Please advise. Here are the errors that I faced No error is reported by Mathcad prime v7.0 but I am not able to remove the last page of the converted file from Mathcad v15.

I have a task to make the code in the left as written in the right but I have an error as attached appreciate if anyone can help.  

Hi all 😀 I have a data group from excel to understand: the 1st column is : Torque the 2 column is : Position the 3 column velocity: Torque   If i make a drawing with Torque (vertical Y axis)  and position (horizontal  X axis), i have this:   I see  i have periodic data : in position , approximately from 50 to 2250 milimeter. this is OK, the data relate to a cylinder which makes round trips   My problem:   How to extract data in new matrix wich include only data for one stroke: submatrix for positionning 50 to 2250 and submatrix for positionning 2250 to 50   and that for the 5 back and forth   I want to make a drawing for forth (torque and velocity) and back (torque and velocity)     Thanks

I cannot install the program. Nothing happens when the installer starts

no

Dear Expert MathCAD Prime Users,While I am doing my assignment of Reinforcement Concrete Column Design I have a problem when I reached design axial compressive  I can not find the Value of a as you can see in my attached file in MathCAD Prime 7.0. The error message is "The function for the end points of the interval must be at opposite signs".  As I mentioned problem, I would like you to show me how to fix  this issue in order I can make a Column Interaction Diagram.I am looking forward for your help and recommend. Thank you!

it won't let me finish the installation after acquiring the license

can't download the program version for 32-bit laptops. if it exists it can reset the program file or link to download the program

There are three random points on the plane through which an arc of a parabola and a similar arc of a catenary pass. What is the probability that the length of the parabola's arc will be greater than the length of the catenary's arc??

Hello friends, I have to calculate a beam on elastic basis by the finite element method for my master thesis, I do not understand why there is an error for plotting the graph.I attached the file.Really need help because the deadline for submitting the thesis is Friday, May 28