PTC Education

I am using PTC Simulation 6.0 and I am not able to use the software.

I had Windows Home loaded, installed Creo, and it opened fine, but when I opened a new prt file, it crashed, (Traceback provided). I upgraded to Windows Pro as indicated in PTC literature, and tried again with the same result. I thought the install may have been corrupt, so I uninstalled, and need help to review my Hardware/Software, and complete the install. I'm hoping my trial start date can be reset as well. I tried going through a new trial request but was referred to PTC Customer Support.

After starting the Programm i am getting the "License request failed for feature" Error. Wfter pressing OK to close the ERROR i get the notifivation that AFX wasn't able to load and after that IFX is not able to load. After pressing OK on all those 3 ERROR Messages the Programm closes.I followed all the steps for the installation with the license code: BK700908EDSTUDENTEDUNI Is there a solution for my problem so that i can use the programm how it should work? 

I have exact the same issue as this toppic https://community.ptc.com/t5/PTC-Academic-Program-Discussions/Creo-Student-License-can-t-renew/m-p/698711 anyone can help?

When i open "creo parametric 6" it says that the program can not run Quality Agent and the error code is 0x06000012   What should i do to be able to open the program?

I have installed creo and added the license file which was given to me from my university. When i open creo, it says license request failed for feature and 7788@DESKTOP- 1987DS8: (-8) Invalid (inconsistent) license key. Warning: (-96) cannot connect to server. What should i do to resolve this issue.

when I try to install PTC Creo 7.0 - Schools Edition on my disk C it doesn't work the installation stops at 65% I had 9.5GB free on this disk but now it's full but before installing it said that the program needs only 8GB for installation. Now I would like to try to install CREO to disk (D:) but couldn't find the setting to change the program location while installing.  

Dear support team, dear community, I recently registered to install PTC Creo on a new device. Although I was able to install Mathcad, Creo Direct etc. I was not able to install Creo Parametric 5.0, which I will need most for my work. What could I do to add it? Thanksalot in advance.   Best regards!

Hi, is it possible to do tolerance analysis in CREO 6 student version? The PTC Acadamic Program FAQ says it is included, but when I push the tolerance analysis button a licence error occurs.    

Error when installing the license number. I have the code BK700908EDSTUDENTEDUNI and BK700908EDSTUDENTEDK12. Neither of them let me go forward. Firstly I was installing without issues with the code BK700908EDSTUDENTEDUNI, but my laptop suddenly restart and the progress was lost. Therefore I tried to install again and for the first time in the space for enter the license appears "Error". I have deleted all the files of Creo and I have been trying hard. I have read the support and changed as I said the code with the ending K12 and it's been the same. Error. Could you please help getting fully installed Creo 7.0.

Hi,I need support.I installed the Creo 7 student version with the Creo license but the program doesn't work. My system is WIN10, 64 bits and I´m from Brazil   Reginato

I am not able to install the creo on my machine and also not yours as I do to get a student use license, I need help

I purchased a student version of Creo on -1-17-21 order #103046868113. The order confirmation says I ordered Creo 4.0 University Student Edition Premium - One Year Term License. I down loaded it and it installed as Creo 7.0.2.0 and give an error message of License failed, License file does not support this version. I can only install what you gave me 7.0.2.0 with a license for 4.0. I have made Two phone calls and this is second attempt to log a case. Today is 1-20-21. Need someone to call me at 713.992.1348

Hi, I m clicking on Creo 6.0Win 64 DVD (3.953 GB) Download Manager HTTPSHelpCenter (1.709 GB) Download Manager HTTPSgetting this message Invalid URLThe requested URL "[no URL]", is invalid.Reference #9.3cb0db17.1610999765.128537f

I am starting a tutorial, the piston, practice session...I installed Creo 7, the tutorial must have been performed in an earlier version.  It starts with a new template, says to use "mmns_part_solid"...you have 2 choices in Creo 7.   mmns_part_solid_abs or mmns_part_solid_rel   Which do I use?  What is the difference between the 2 extensions?   https://learningexchange.ptc.com/go/new_creo_user

I want to download creo for my college use

Hello PTC community. I am asking for assistance in making an extruded figure for a geneva cam. I spent a while figuring out dimensions since instructions were not clear to me and now I am struggling with extruding my sketch. I have attached the instruction's reference image as well as my creo part. The error I am getting is that there is overlapping geometry and my sketch is not looking symmetrical.   Note: the center for the three arcs (of Radius R2) is at the origin.   Could someone please fix my mistake and point out a simple way of fixing the geometry? Much appreciated, thank you.

When i installed Creo Parametic 5 for Students i was connected via USB-WLAN Stick. Now i am using a Fritz powerline Plug with a different MAC ID of course. sadly CREO won't work with the old license, please send me a new license with for my physical adress: BC-EE-7B-8A-01-46   Thank you!

Hello everyone. I have some troubles with the installation of Creo 7.0 Student edition. The first time I managed to download and use the software (from https://www.ptc.com/en/academic-program/academic-products/free-software/) I got the 7.0.1.0 version but now I find 7.0.0.0 as latest version (I suppose for the bug found in the former). Then I tried to migrate the software into an external hard drive and it stopped working (if I remember correctly I got error 0x00000003). I then uninstalled all the applications and deleted the licenses .dat files. I try to reinstall the software and when I enter the simple license code (BK700908EDSTUDENTEDUNI) the installer program does not respond for some instants and then it shows an error under the license field. How can I solve this problem?   I run setup.exe as admininstrator, accept contract and insert license codeAfter entering username and password and clicking "Install licenses"And finally I get this.

Hi there!   Just installed the academic version of Creo Parametric 6.0.2.0 but the license cannot be found. I got a license pack via mail and want to know where to put the file in? Thanks in advance! 🙂  

Hi! I recently updated my desktop to Creo 4.0 to test it out ahead of our FTC teams adopting it, and I'm noticing some major stuttering and lag, particularly around the measuring tool, when I have relatively complex models open. This wasn't present in Creo 3.0, and while it's still functional like this, it is very irritating. Does anyone have advice for alleviating this? Also want to say I'm a little disappointed that rendering now requires a special license-- in my opinion creating cool renders of their work is a great way to get students interested in CAD. Best, Nick

I'm trying to install Creo (University Student download, 7.0). I got to the step where I input the the student license (BK700908EDSTUDENTEDUNI) but I got an error (did not get "Success!" message). I skipped the license step to complete the install.If I try to launch Creo Parametric (7.0.2.0) I get a Warning Message List "License request failed for feature." Can you help me where I need to enter my license? And why I got an error inputting the university license during initial install?I installed this on my old computer (just built a new computer) so maybe I have an issue trying to install Creo on (2x) computers?Thank you!

I need a female manikin for an animation, but only male is available. Anyone know where I can download and install the female manikin assembly?

Hi I signed up to download Creo 3.0 about a month ago but just now got it downloaded. In the time that past I don't remember how to get my software license. Thanks for the help.Micah

I am an professional engineer and have my own commercial license of Creo. I am also a coach of a FIRST Robotics FTC Team and wish to help my kids with learning and using Creo. I know I can't open any of their files with my commercial license nor can I create files for them to open. I understand why so I just want to make sure I can set my machine up to run the academic license to review their work and support them.Does anyone know if I can run both a commercial license and academic license on the same machine?If I can, what things do I need to do to not mess up my current commercial configuration?Thanks for any Help, MarkP.S. If this is the wrong forum to discuss this, I appologize and hope someone could direct me to the correct place to get help.