Archive Read Only

Is it just me, or does everything have to be pre-approved by a moderator now?

All,I found and posted on here a list of what the icons all meant in the model tree (for example, supressed, etc.). I can't seem to find it again. Anyone have the url (namely the person I sent it to, lol)?Wayne

could some one please expalin the difference between the two different shrinkage formula's in Pro/Engineer.(1+S) and 1/(1-S)?

How do you import points from an Excel spreadsheet into Pro/E?

Is it possible to create a left handed coordinate system in Pro/E - Creo? If so, how do you do it?Best regards,Janet Grove

Dear PTC Comumunity,does anybody know what to do when my creo 2.0 shows error: 0xc6000005Hopefully can somebody help me.kind regards,David

Register:http://ptccreoevents.com/?c=USA&et=

hi allWhat value can be used for coefficents of friction (static and kinetic) and restitution in dynamic analysis.Does it depends on rpm.Also suggest a book if it has addressed such question.Thanks

日本語のディスカッションは可能ですか?

Testing

Help, I am trying to assign a raw material number based on a tubes height, width and thickness through IF statements. Any suggestions?

There is a special place in 7734 for spammers. The sooner you find it, the better.

we werwerwerw

Xeon W1650 @ 3.2G, 8GB Ram, Win 7 64.

a simple caseIf i have a gear and a a ground body.the gear rotates through a motor.thenDOF=6M-N-Oin this case M is the bodies except ground which is 1N is the total number of contraints imposed by joints.in my cas it is pin so it restricts 5 constraintsO is the driver which is 1.Putting these in the Grubler equation gives DOf=6*1-1*5-1=0but i know that it should be one degree of freedom.ie as it rotatesthe system types measures of DOF also gives 0.What is the reason it gives 0 instead of 1.

Gurus,Anyone have a clue on how to find and delete "Curve id 307" (see image)?CREO 2.0 m040Windchill 10.0 m030Thanks,Eric

can u pls explain, how to create a new pen_table_file and edit to various pen values you mentoned above.. i can't able to create that.. i followed the steps Tools- options,my window looks like belowbut i can't found pen_table_file on that window, pls guide me how to move further to create a new pen_table_file and edit the values..

Has anyone established a wiki for user documentation (tips, standards, how to, etc) at their company?Any suggested architecture for setting up a wiki?

Hi FriendsI have one query that can we measure a spring wire length in pro-e. If we want to make a spring and we want to know what length of bar we required making a spring in industry then how we calculate this?Please help on this????

What's wrong with this picture...Can I count on doing an update this weekend, PTC?

Hi- I have a question about inheritances. I have a model with many inherited cuts and I want to verify that all inheritance cuts are up-to-date with the "base" model. Ideas?Thanks in advance,Jason

I have an e-beam weldment for which I am using Inheritance Merge. The smallest component of the merge is significantly smaller than the largest component. From the resource reading that I have done I should be using Absolute Accuracy with same value in all components of the merge. I cannot make this happen! The smallest component prompts me that its allowable range is 4.63787968993e-06 to 0.000463834348. The largest prompts me that 0.0004880633 to 0.048811210617 is its allowable range. The two ranges do not meet or overlap. I have not been able to find a solution to this yet. Suggestions please?FYI I am using creo elements/pro 5.0 build M120.M

I'm trying to pass a numerical value to a bulk item and set BOM_REPORT_QUANTITY to that value and am so far not having any luck. Anyone else able to get this to work?Thanks,Kevin

is it possible to plug EFX7.0 M010 to CREO2.0 M060 ?