CAD

I am using Creo Parametric Release 9.0 and Datecode9.0.0.0Totally new to Creo. Trying to open up the ability to edit the configuration settings in ModelCHECK (Check Files, Start Files, etc.) so that we can create custom defaults- currently these options are greyed out. Can these settings be unlocked or what is the procedure to accomplish this? Thanks!

Hello In drawing modeis modelcheck able to assign  parameters values from current 3d model to the drawing parameters?If yes how?

Every time I first get onto the windchill server in Creo and am connected to a Windchill server, the authentication dialog (genlwsc.exe) opens behind the active window as shown with its icon blinking yellow. Any solutions for this???   The current 'solution' https://www.ptc.com/en/support/article/CS303945, is to manually select it which isn't a solution.   Thanks.  

Can I have a licence?

I am using Creo Parametric Release 6.0 and Datecode6.0.5.1unable to import word files in drawing.Once i did its going to not responding in creo

Is it possible to import multiple XML files, from Creo Schematics, into a single Creo Parametric Cabling component? In the past, my attempts to import multiple XMLs has caused the the new one to overwrite the old one.  I figured out it's possible to manually copy and past information from one XML into another using Notepad++. It's an inelegant solution and prone to error, but it does seem to work. Does anyone else have any better ideas?

Hello, ProGtolDatumReferencesGet(datumRef, &basic_datum, &basic_matcond, &compound_datum,&compound_matcond) has been deprecated and changed to ProGtolDatumReferencesGet(gtol, &primary_datum,&secondary_datum,&tertiary_datum). I am trying to figure out how to get the compound datum out of the new function, but after searching through the TestGtol.c, I learned that the sample otk only contains information on how to retrieve the basic datum from this function and not the compound datum. Any and all help would be appreciated. Thank you,Mark

How must I set up the XMCD, MCD converter for Mathcad Prime 8.0.0.0 ?

Hello everyone,I recently ran a sensitivity study with 20N load applied on the model from 0° to 360° from the start position thanks to user skunks's help! I also defined many points to obtain the strain values from the study. I am wondering if anyone knows  1) if I can export the measurements in the .csv like what a static analysis do? 2) Can I create a parameter relation feature in Creo with the user-defined measurements? And then have Creo plot the final results vs. angle?  (Related post: https://community.ptc.com/t5/Analysis/How-do-I-define-a-load-that-rotates-from-0deg-to-360deg-from-the/m-p/830717/emcs_t/S2h8ZW1haWx8a3Vkb3N8TDlCUDlDNUJRSzZWMkZ8ODMwNzE3fEtVRE9TfGhL#M10924)  Thank you so much! 

I am using Creo Parametric Release 9.0 and Datecode9.0.0.0I am running Creo Installation Assistant. Every time I enter the sales order number under "Node Locked License Generation" in the License Identification section, I keep getting an error message.Here are the errors that I facedError! License request for this SON is in process. Please verify that this has completed successfully and contact PTC License Management if necessary.I saw that there is a support case made on my behalf. But does it usually take this long?

We are planning to upgrade Creo Parametric to Creo 7.0.9.0. Could you please provide what are the main updates in Creo 7.0.9.0 vs Creo 7.0.5.0?   Thanks KB

I am using Creo Parametric Release 9.0 and Datecode9.0.0.0About Model CheckMy model check report is coming up blank.I only use it for overall size of part.

so when we create a datum and the a gtol the two associate in creo the problem though is if they are both on different view states in the model the association doesn't show. Is there a way to i click a gtol in one state and have the datum from another show. if it not can i have a note or something pop up telling the person where which state the datum exists in?

Using VB API with Creo 5 and as mentioned in the help file, I have set the configuration option regen_failure_handling to resolve_mode in the Creo Parametric session. Even after that solid.Regenerate(Nothing) does not regenerate the model. [EDIT]: Subsequently I created an object of type CpfcRegenInstructions and passed it to the Regenerate method as an argument, but the following line says "Class not registered":Dim creoRegenIns As CpfcRegenInstructions = New CpfcRegenInstructions ForceRegen, RefreshModelTree, UpdateInstances, and AllowFixUI are all set to True. Is there any solution to this?Thank you. ~Tushar

Dear colleagues,Mathcad 3, Windows 10. I resolve the system of equations. I defined the function named "Pt(I,I2,...,Cbb)" which consist solution (''n'', and ''p") of these equations.  In the next solve block, I try to fit experimental data - two rows - N33, P33 (where I1 is X). But unfortunately, minerre algorithm does not work giving me the error. The program is a bit busy, but the main problem is only in the last solving block. Probably someone could identify a problem in the syntaxis of the last solving block which tries to fit data by function "Pt" and parameters "Nt" and "Et". Probably the problem is that "N" and "Et" are vectors.   

with the VB API on Creo 5 I am using model.Erase()followed bywindow.Close() But the window remains open, though the model is erased.Is there a solution for this? Q: What is the equivalent API for 'Erase not Displayed'? I also tried window.Clear()but that was of no use. Regards,~Tushar

I am using Creo Parametric - Release 6.0 (connected) Release 6.0 and Datecode6.0.5.1I need to open a modelfamily with pfcls in Powershell. Currently I'm only able to open the main model without the family.Can anyone help?

I am using Creo Parametric Release 4.0 and DatecodeM130使用VPN时，Creo无法连接对应的License.提示7788@xxxx （-9）Invalid host.(license服务器所在电脑已开放7788端口)Here are the errors that I faced提示7788@xxxx （-9）Invalid host   When using VPN, Creo cannot connect to the corresponding license. It prompts 7788@xxxx (-9) Invalid host. (The computer where the license server is located has opened port 7788) Here are the errors that I facedPrompt 7788@xxxx (-9) Invalid host   Translated by Iuliana Lazar with Google Translate on 17 Oct 2022

The width/height handling for tables in a drawing is extremely stiff and slow.  Is it possible to make the table rows, columns and/or cells to grow dynamically based on the amount of content (eg text)? This would for example be handy for description and material columns in a BOM-table, the description column in a revision table or unassigned text boxes.  If not, I'll post it as an idea... 🙂 A related idea regarding dynamic text size is already posted, but I don't see it as a good solution as the text would become unreadable once it's below a certain size:https://community.ptc.com/t5/Creo-Parametric-Ideas/Dynamic-Font-Height-option/idi-p/813418 Even though this video is meant as a help/guide/tutorial, it also shows the heavy amount of clicking and trial and error before the table actually get the necessary size for the text within it:https://www.youtube.com/watch?v=Tn2X8_KmFSsAnd in case the text is changed, you have to redo it all again...

 

Hello everyone, I would like to simulate the stress vs. load angle in Creo. Instead of creating individual load set for every 20 degree, I would like to see if there is a way to define the load with the parameter relation, and make Creo run the analysis for with a new load for every 20 degree.  The load magnitude will stay the same, but the direction will change. Thank you so much!

Hi,New Creo user here and I have searched the forum already for this issue. Every time I open a model, Part or assembly, it displays the style as 'Shaded'I have to change it every time to 'Shaded with Edges'.Is there any setting or option to keep the model 'Shaded with Edges''? Regards,~Tushar 

https://youtu.be/_s5RFgd59ao

I'm in the "Acquisisci Licenza"(Acquire License) phase of the installation of PTC MATHCAD. The issue is that while I'm getting the free 30 days of mathcad prime, the installation tool tests my eligibility to the program but stops telling me that "Servizio licenze occupato" (busy licensing service).I'm an MSc student of Aerospace Engineering so I should be eligible.Thank you.

Greetings,  I have several sets of data for the tested strength of a material. The maximum number of data points in each data set is 5, so I really don't have a lot to work from. Also, I'm not as handy with statistics as I would like to be, so I'm throwing this to you guys. I need to take this data into a function and output a single value that represents the predicted safe lower limit of the data set for which 95% of all future tested samples will be higher. I'm basing this function on the Kolmogorov–Smirnov statistic and Student's T test.  The intention is to determine the safest strength of material based on tested data, but not be too conservative. I wrote this to do what I intend, however I'm not 100% sure if what I'm doing is based on sound statistical thinking. Below is a screenshot of the function and attached is the worksheet. Please, play with it and inform me of your thoughts.