Creo+ and Creo Parametric

I am using :Creo Parametric 7.0.7.0 Windows 11 Professionnal Version 22H2I have a search.pro file and I specified its location with the search_path_file option in the config.pro file. The locations contained in the search.pro file contains standard parts that will never change. My issue is that when saving an assembly, I would like to save all the parts but not the ones contained in these locations. Is it possible to achieve that and how ?

I am creating a UDF of the J1926-1 feature on the end of solid round bar.When I run the UDF on other locations, the revolves and extrudes 'flip' and do not follow the way they were created.  Using the hole command, I have been able to create the spotface, drill depth, etc without any issues.  When I run the UDF, the helical sweep cut (thread) of the feature flips. I have created other UDFs of this same feature and all appear to work correctly.  Any ideas of what I am doing wrong?

Attached to this blog post is a short presentation and a video on the new enhancement to allow replacing the model of a drawing view with a related model in Creo 4.0. Any questions or feedback you have related to the ability to replace the model of a drawing view should be provided as comments to the blog post. That will be the easiest way for me to keep track of the comments and also be able to provide timely responses to your questions. If you follow this post, you can be notified of those comments as well and be able to learn from what others are asking. I may also periodically update this post to add some new details or information related to this enhancement.   Also, don't forget to follow the main blog post for 2D Detailing - which will have links to other 2D Detailing-related content  2D Detailing Home:  Start Here!

I am using Creo Simulate Release 4.0 and DatecodeM150I have parts upon which we ran structural simulations in the past. I wish to now run a fresh simulation in assembly mode. When I have my assembly in session, and go to simulate, I get all these failures due to bad constraints and load sets. I want to start fresh and try to use HOME / SET UP / NEW SIMULATION MODEL. However, New Simulation Model is greyed out.I also cannot delete individual constraints or loads in the model tree.

I'm trying to create a drawing of a multi-body part, with a bill of materials table, like an assembly drawing. (I've created a multi-body part as it's quicker than modelling an assembly.) I've named my bodies and created a BOM table using one of the built-in templates, which generates a unique item number per line, but I can't figure out how to make these item numbers appear as balloon notes.'Create balloons' on the toolbar only seems to work for components, not bodies.Is there a way to make this work?  Or do you just have to create manual balloon notes?

I am using Creo Parametric Release 9.0 and Datecode9.0.0.0In my main assembly I am trying to assemble jumpers assembly as a flexible component. Earthing jumpers are two sub-components, so I am trying to assemble in different lengths and directions. I am able to constrain distance and it works fine, but direction of the subcomponents will be different, I cannot rotate subcomponents, only earthing jumper rotates. For example, in the first position Earthing jumpers have two subcomponents, component 1 should have an angle offset of 35 degrees and component 2 should have an angle off set of 65 degrees. In the second position, in the same way, component 1 of Earthing jumpers should have an angle off set of 45 degrees and component 2 should have an angle off set of 25 degrees. Let me know what is the best way to keep them consistent.

Dear PTC Team, I have created & modifed on Huge ASsembly file for one of my project. After couple of days, While Opening same Assembly file again for some modification, Creo 10.0.2 software keep getting crash. Do you have any solutions for such Crashes.

This occurs when clicking "OK"  or deleting datum planes,  the Regeneration Progress window overlays Creo and wont let me continue. Solution is still to end it all through task manager and deal with the file loss. I don't want to run into this problem in the future when I'm working on something much more time consuming, does anyone know of a solution?Thank you for looking into this for me.      

 I would like to know how to import the CSV data into MODS when I generate several combinations in other software, in this case it would be several points, but Creo comments that the imported data is wrong, would there be a correct way to import?

I am using Creo Parametric Release 8.0 and Datecode8.0.5.0Hello,I will write Gpost for Siemens 840 D control units, but I didn't get the gpost output as belowCS_TOOL("T60")CS_TP("T11")When I got the gpost output, I got it as belowT2 M6T1How can I change Tool output as CS_TOOL and CS_TP in the GpostCS_TOOL= Tool to useCS_TP=a next tool

I had the following request in today from a customer. How do I delete the references used in an NC step, Using the references right mouse click doesn't allow the option. Customer on Creo 4 F000, I have also tested on 10.0.2.0.Only way seems to be to edit the Tool Motion entries.

Currently running 9.0.5.0 on two work stations and the issue as stated in the following post was not resolved:   https://community.ptc.com/t5/3D-Part-Assembly-Design/Cursor-not-visible-in-family-table-cell/m-p/875073/thread-id/129131#M129649   Going to either open a new case or see if the previous one can be reopened.   (Previous case: 16880414)

a) Does anyone have experience with the stability and performance of Creo Parametric on an Intel Core-i9-13900 or 14900 CPU? b) what motherboard and chipset is advised?c) There is also a chipset which supports ECC RAM memory.  Is it needed for a good stability of Creo ?d) Is ECC RAM needed for a good stability of Creo Simulation Live ?e) How is the sound level? Is it silent or a lot of noise when high performanceis asked?f) How is the experience with over clocking the CPU to about 5.8 GHz regarding above questions? g) Comparing the specification with Xeon processors the Core i9-13900 may perform better.- Is this also the case in practice?- Is this also the case when not using the over clocking?h) Is Creo always using the Performance Cores of these CPU and how is this managed?i) How reliable is the Core i9 and what about lifetime when over clocking with respect to a Xeon processor?j) Is over clocking possible or can this performance increase not be earned and is it downsc

Attached to this blog post is a short presentation on the new enhancements to Dimensions in Creo 4.0 in Drawing mode. Any questions or feedback you have related to Dimensions should be provided as comments to the blog post. That will be the easiest way for me to keep track of the comments and also be able to provide timely responses to your questions. If you follow this post, you can be notified of those comments as well and be able to learn from what others are asking. I may also periodically update this post to add some new details or information related to Dimensions.   Also, don't forget to follow the main blog post for 2D Detailing - which will have links to other 2D Detailing-related content 2D Detailing Home: Start Here!

Check out this video on Creo Composites from PTC Application EngineersPresenters: Lee Goodwin (Technical Specialist, Principal) and Ryan Butcher (Technical Specialist, Fellow)Original Date Presented: August 15,, 2023To dive deeper into the subject, check out Creo Composites Learning.  

The middle mouse button does not complete the feature (example line chain).  I was on Creo Parametric 9.0 and just downloaded 10.0 both the student edition.  It was happening on the tail end of 9.0 and continued in 10.0      

Good afternoonI am using Creo Parametric Release 8.0 and Datecode8.0.7.0I' m using CreoJs in order to automate some tasks in Creo.From CreoJs, I'm trying to make a call to Windchill REST services.It works well for a GET request by using "downloadJSON" function from Additional API Features Introduced in Creo.JS in CreoJs user guide.My issue is when I want to do a POST request.I use "uploadJSON" function to be able to send a JSON object with body definition and the nonce token in the header.It always return an Invalid Nonce token error.Is someone could help me on the correct use of the uploadJSON function to send a POST request with headers?Or what are built-in function of CreoJs to perform a POST request?Here are the errors that I faced"statusMessage":"400: {\"error\":{\"code\":\"INVALID_NONCE\",\"message\":\"A potential security problem was detected. Refresh the page and try again. If the problem persists, contact your administrator.\"}}"

As per the original post.    Hey,   Is the play trail file option not available for student version ? 

creo 4.0 m100toolkit  visual studio 2015 not working

Hi, I am new to Creo. I have tried to use the Spline tool and I can't add another point OR delete an existing point upon creating a spline. I am usually forced to delete the spline and recreate it in case I want extra points or fewer points. Is there a way I can edit the spline i.e. adding another point or deleting an existing point? 

Hi everyone. Is there any option in CREO Parametric,  to 3d-draw flexible components such as hoses and cables after their natural properties such as weight stiffness tension rotation etc.? I want to draw some water hoses in a machine, so that the hoses can behave after their real structural propertires, not only forces by my restrictions. Thank you so much in advance for your help. Br,Hasan   

I am using Creo Parametric Release 4.0 and DatecodeM040User is not able to fetch NRB templates.Here are the errors that I facedUser is not able to fetch NRB templates.

how to enable this option in creo9.0  

I am new to combination states. When I create a new combination state, all of my default datum planes get hidden and I can not unhide them using layers or the model tree. But I need them because I want to move dimensions to those planes. Does somebody maybe know how to bring back the default datum planes when you just created a combination state? Thank you for looking into my question!

Hi everyone,What are your favorite features, shortcut, or lesser-known capabilities in Creo that has significantly improved your workflow? I wanna know. 🙂