Creo+ and Creo Parametric

Hello,I have a problem with the firewall of my Windows server 2022 blocking the FLEXnet Admin License Server program, when I go to Private network settings and set it to turn off the machines access normally, I have already released the path C:\Program Files\PTC\FLEXnet Admin License Server\lmadmin.exe but it still gives an error that there is no license something else needs to be done?

I'm using the parameter "&harn.run.len" to bring the length of my wires into my wiring table. The network length used on my model is also displayed (284.004). I know it is the network because I had one of the parameters entered incorrectly and in the "Wire Name" column it said "Network".How can I exclude the network?Finally how can I get the pin name to appear? I'm using "&harn.run.cond.from.pin.name", "&harn.run.cond.to.pin.name"All in Creo Parametric 8.0.9.0. 

Hi, Creo 9, Windchill 12.1.2 I have a need to create (lots of) simplified files (to protect IP) in order to send them out. There doesn't seem to be a good solution which fulfills everybodies' needs but here's what I would love to achieve. Save as -> Shrinkwrap doesn't have an option to choose a "subset" like the feature-creating version of the tool does. This sucks because once I create a shrinkwrap file I don't seem to be able to edit it in any way(add/remove parts and it won't update if a part is updated). So 1) Am I missing something or saved shrinkwraps can't be updated because they lack the parent-child relationship to the original assembly? Based on the above - in order to have control over what's included in the shrinkwrap I create a feature shrinkwrap inside the assembly. Then I create a save-as shrinkwrap of the feature-based shrinkwrap. This kind of sucks cause the feature stays in the assembly...and the part-type shrinkwrap doesn't update. Bu

I started having this issue today (my first time attempting to install creo). Since the first try I have uninstalled and deleted all license files then reinstalled Creo (using the same zip file I downloaded the first time).  Still getting the same issue.  The license I received yesterday results in an error message, the message is long but this seems to be the critical data:  License Request Failed for Feature... (-21) I am using the educational license fixed node (just followed the directions that I received when receiving the license). Any suggestions on how to get it up and running? Thank you 

When I created 3D dimensional marking in the Annotate module, the tolerance text height was the same as dimension text height. Usually, the tolerance text height factor should be 0.6, which means the tolerance text height is 0.6 times of dimension text height. I have set tolerance_standard from "ansi" to "iso", but the tolerance text height was still unchanged. Is there anyone knows how to change the tolerance text height in 3D annotate? Your help will be much appreciated!  

(Creo Parametric 10.0 ) Before I do the analysis definition, I already add a servo motor. However, I can only use the motor when the type of the analysis is position. And the right three buttons can't be used.

Is there anyway to enable the clock parameter in Creo 10?

I am using Creo Simulate Release 9.0 and Datecode9.0.0.0Simulate static analysis taking time more than expected.It is stuck in preprossing following activity taking huge time:-"Pre-processing boundary (70% complete after   2.1 min)"

Hi,as specified in Article - CS7762it is not supported to  add an older version using As Stored dependent.did any of you managed to achieve the goal using other techniques ? what about using it in conjunction with  AddToWorkspaceAction ?  

Thought I'd give back a bit to the community, one secret weapon that I've been leveraging for quick and dirty automation is to access the asynchronous VB API through PowerShell. VB API is a .NET construct, so it's accessible through VB, C#, as well as PowerShell. API wise, it is almost 1:1 with the base J-Link package, so you are not missing out on much. You will not have Toolkit functionality, but you can in theory create Toolkit DLLs to load in via config.pro that you can invoke via the VB API.   The convenience of using PowerShell is that it is deployed by default on all machines Win7+. You may run into some compatibility issues with Powershell V2, since that was a rather primitive version compared to what we have today. Win10 deploys with Powershell 5 and above. It is also a shell environment. You do not need to compile anything or open any special program, you can literally link up in a new shell window and immediately start piloting Creo. So far I can pretty much create a qu

Hello all, I am a fairly new user to Creo, so bare with me with some of the terminology, but I am having an issue with exporting a 2D sketch in Creo. When I export the file (shown in the pictures attached) and import it back into Creo the file shows up blank with only a picture of the DXF file that I was trying to make. I have tried importing the DXF on SolidWorks as well and this also results to the same issue. Does anyone know why this happening? Thank you in advance!

The system colors, for example system_geometry_color, can be set via specifications in a file. For example, I use "syscol.scl". To the best of my knowledge, there is no documentation of what parameter names are available for these settings. Equally important, it is not clear what effect setting any of these parameters will have. I'm wondering if anyone has any documentation of the following: (1) Parameter names (2) Screen elements affected by a given parameter (3) Syntax for the settings file, i.e. what alias_sec_dim_strong_color_to means, the color value ranges, etc.   I had asked this same thing as an Idea for it to be added to the Help documentation. It was pretty much ignored. I naively thought that such things would be documented and available, but that does not appear to be so.

I am using :Creo Parametric 7.0.7.0 Windows 11 Professionnal Version 22H2I have a search.pro file and I specified its location with the search_path_file option in the config.pro file. The locations contained in the search.pro file contains standard parts that will never change. My issue is that when saving an assembly, I would like to save all the parts but not the ones contained in these locations. Is it possible to achieve that and how ?

I am creating a UDF of the J1926-1 feature on the end of solid round bar.When I run the UDF on other locations, the revolves and extrudes 'flip' and do not follow the way they were created.  Using the hole command, I have been able to create the spotface, drill depth, etc without any issues.  When I run the UDF, the helical sweep cut (thread) of the feature flips. I have created other UDFs of this same feature and all appear to work correctly.  Any ideas of what I am doing wrong?

I am using Creo Simulate Release 4.0 and DatecodeM150I have parts upon which we ran structural simulations in the past. I wish to now run a fresh simulation in assembly mode. When I have my assembly in session, and go to simulate, I get all these failures due to bad constraints and load sets. I want to start fresh and try to use HOME / SET UP / NEW SIMULATION MODEL. However, New Simulation Model is greyed out.I also cannot delete individual constraints or loads in the model tree.

I'm trying to create a drawing of a multi-body part, with a bill of materials table, like an assembly drawing. (I've created a multi-body part as it's quicker than modelling an assembly.) I've named my bodies and created a BOM table using one of the built-in templates, which generates a unique item number per line, but I can't figure out how to make these item numbers appear as balloon notes.'Create balloons' on the toolbar only seems to work for components, not bodies.Is there a way to make this work?  Or do you just have to create manual balloon notes?

I am using Creo Parametric Release 9.0 and Datecode9.0.0.0In my main assembly I am trying to assemble jumpers assembly as a flexible component. Earthing jumpers are two sub-components, so I am trying to assemble in different lengths and directions. I am able to constrain distance and it works fine, but direction of the subcomponents will be different, I cannot rotate subcomponents, only earthing jumper rotates. For example, in the first position Earthing jumpers have two subcomponents, component 1 should have an angle offset of 35 degrees and component 2 should have an angle off set of 65 degrees. In the second position, in the same way, component 1 of Earthing jumpers should have an angle off set of 45 degrees and component 2 should have an angle off set of 25 degrees. Let me know what is the best way to keep them consistent.

Dear PTC Team, I have created & modifed on Huge ASsembly file for one of my project. After couple of days, While Opening same Assembly file again for some modification, Creo 10.0.2 software keep getting crash. Do you have any solutions for such Crashes.

This occurs when clicking "OK"  or deleting datum planes,  the Regeneration Progress window overlays Creo and wont let me continue. Solution is still to end it all through task manager and deal with the file loss. I don't want to run into this problem in the future when I'm working on something much more time consuming, does anyone know of a solution?Thank you for looking into this for me.      

 I would like to know how to import the CSV data into MODS when I generate several combinations in other software, in this case it would be several points, but Creo comments that the imported data is wrong, would there be a correct way to import?

I am using Creo Parametric Release 8.0 and Datecode8.0.5.0Hello,I will write Gpost for Siemens 840 D control units, but I didn't get the gpost output as belowCS_TOOL("T60")CS_TP("T11")When I got the gpost output, I got it as belowT2 M6T1How can I change Tool output as CS_TOOL and CS_TP in the GpostCS_TOOL= Tool to useCS_TP=a next tool

I had the following request in today from a customer. How do I delete the references used in an NC step, Using the references right mouse click doesn't allow the option. Customer on Creo 4 F000, I have also tested on 10.0.2.0.Only way seems to be to edit the Tool Motion entries.

Currently running 9.0.5.0 on two work stations and the issue as stated in the following post was not resolved:   https://community.ptc.com/t5/3D-Part-Assembly-Design/Cursor-not-visible-in-family-table-cell/m-p/875073/thread-id/129131#M129649   Going to either open a new case or see if the previous one can be reopened.   (Previous case: 16880414)

a) Does anyone have experience with the stability and performance of Creo Parametric on an Intel Core-i9-13900 or 14900 CPU? b) what motherboard and chipset is advised?c) There is also a chipset which supports ECC RAM memory.  Is it needed for a good stability of Creo ?d) Is ECC RAM needed for a good stability of Creo Simulation Live ?e) How is the sound level? Is it silent or a lot of noise when high performanceis asked?f) How is the experience with over clocking the CPU to about 5.8 GHz regarding above questions? g) Comparing the specification with Xeon processors the Core i9-13900 may perform better.- Is this also the case in practice?- Is this also the case when not using the over clocking?h) Is Creo always using the Performance Cores of these CPU and how is this managed?i) How reliable is the Core i9 and what about lifetime when over clocking with respect to a Xeon processor?j) Is over clocking possible or can this performance increase not be earned and is it downsc

The middle mouse button does not complete the feature (example line chain).  I was on Creo Parametric 9.0 and just downloaded 10.0 both the student edition.  It was happening on the tail end of 9.0 and continued in 10.0