Creo+ and Creo Parametric

I am using Creo Parametric - Release 7.0 (connected) Release 7.0 and Datecode7.0.2.0im new at this so maby this is not the correct place to ask, but is sure looks the bestwhen making a restricted parameter with a text document i use µ in one of the options, but in creo when selecting the option it shows "µ" instead of "µ".i tried some other sybols and it does the same thing with the Âannyone know whats going on?

I am using Creo Parametric Release 3.0 and DatecodeM190ModuleWorks Simulation doesn´t start, Creo Parametric crashsHere are the errors that I facedFatal Error

Hey all, first post here. I am trying to use the swept blend feature to remove material as shown below. I am using a start sketch and an end sketch to drive the geometry of the swept blend and I am using a curve that I created by points (many!) on the outside surface of the original geometry. The issue that I am having is the swept blend is not working very well and leaving a lot of excess material. Also, it is not following my curve very well. I tried using two trajectories but I do not think that is allowed. I have been struggling with this for may days now so any help is appreciated. The end goal is to remove material from the center section and have it tapered on the edges at like a 45* angle, which you can see from sketch.

Hi Team,I am trying to resume some suppress features in part file.Resume option is not available..Any suggestion

Without using "ProMarcoExecute" and "RunMarco" , how to use the TOOLKIT or Object TOOLKIT to scale model ? I have been looking for the "Scale Model" function in the API Wizard, but unfortunately, I did not find it. Why don't I want Marco's way to execute "Scale Model", because the TOOLKIT or Object TOOLKIT program will lose control of CREO after executing marco. Is there a way for the program to keep control of CREO? 

HelloI have a table with many indications about a threading including the helix angle. my part and the drawing are in mm and degrees°, but for a supplier we need the have the angle in degree minute second in the table. I looked at the information page with all the &parameter and didn't find how to change the unit just for this value (not the whole file).I think it may be &parameter[something here] just as the number of decimals.Do you know how to do it please ?What I want : What I have :

I am using Creo Parametric Release 8.0 and Datecode8.0.0.0Hello, we have produced a Creo C++ otk plugin - all works fine. But we have a problem with how we deploy. We use TeamCity https://www.jetbrains.com/teamcity/ to run our build pipeline (so we must build all the code and then use the resultant dll for packaging up. We know that we have to use protk_unlock.bat to unlock the dll. The problem is that we have multiple servers to do the Team city builds and teh same one is not used each time. We are assuming that Creo has to be installed on those machines and also the licenses can only be set up on manual install. Is is possible to do unlocking in a less heavyweight way (but still access the license server that allows protk_unlock.exe to run)? I hope this makes some kind of sense? Can give more details if needed. Any suggestions welcome

Check out this video on Creo Parametric Ansys Simulation Tips and Techniques session  from PTC Solution Consultants.Presenters: Jason Petersen (Solution Consulting, Principal) and Ryan Butcher (Solution Consulting, Fellow). Creo 9.0 What's New  

Hi, when I display a shaded view into my 2D drawing (i.e. to show painted areas) is it possible to activate in this view different appearance settings which I have defined in View Manger?

Hi,How can I resume an already suppressed feature by using relations? For example:IF d12==100ADD SUPPRESSED FEATURE     INTERNAL FEATURE ID  570     PARENTS = 410(#12) 1305(#17)AND ADDAND IF If the feature is already suppressed and the equation (if d12==100) is true, the feature that gets added is in a suppressed state. How can I fix this?Is there a conditional statment that removes "SUPPRESSED"?Or is there a syntax in pro program that will regenerate automatically?

How do I add tolerance to a dimension from an inheritance feature?Tolerance in the model is set to symmetry but after inheritance the Tolerance is at Nominal and can not be changed (greyed out)This thread is inactive and closed by the PTC Community Management Team. If you would like to provide a reply and re-open this thread, please notify the moderator and reference the thread. You may also use "Start a topic" button to ask a new question. Please be sure to include what version of the PTC product you are using so another community member knowledgeable about your version may be able to assist.

Hello, everybody, Does anyone meet the problem when saving the part file to step, the lattice design is missing?For example, in the first picture, I created a lattice structure, I then saved it as step file.But when I open the step file, it appeared as the second picture.

We are an engineering company in the Northeast with offices in MA & VA. And we have suppliers in many states in the USA, and some outside. We have situations where we want engineers from our 2 offices, sometimes co-development partners and, more often, suppliers to review designs and provide written feedback and/or preliminary quotes or DFM issues. We do not want to open up our PLM system to anyone outside.If you or your company have faced this issue and have implemented a solution, I would appreciate if you could share some details about your experiences.ThanksKristin

Is there a way to set the default zoom value when using the common files - workspace as i keep having to use the mouse wheel to zoom in/out.

Hi,please see attached pictures - first ist the standard output I get in Creo (picture 1) but I want to have the letter in line with the section line by default and also the section line should by longer by default (picture 2)Is this possible via a config setting? - by standard not to move always manually the letter.Is this possible with some config settings? 

Hi, I want to change the standard frames which are shown in the sheet setup/format. I know I can load my own frames but I would like to have them shown in the drop down menu.Where can I change that setting? 

I sill have boxed edges in PDF prints despite these settings in the config.pro Why does the settings not work?  

I have just started learning Creo, after years of Inventor and Solidworks. Is there no concentric assembly constraint? When I put a pin in a hole, how is that a coincident constraint?

Hi,I want to select a feature using a macro, but instead of writing ID FEATURE, Creo use the NODES. Example:mapkey(continued) ~ Select `main_dlg_cur` `PHTLeft.AssyTree` 1 `node3238`;\ Is it possible to write:mapkey(continued) ~ Select `main_dlg_cur` `PHTLeft.AssyTree` 1 `feature ID 235`;\  Thanks

I am using IFX in Creo 8.0.4.0 for my fasteners. The models are working fine but is there a way I could set the PTC common name of the fasteners to reflect some string that I would like? At the moment the generated fasteners have a common name which is the same as the part name. My BoM table is set to read the asm.mbr.PTC_COMMON_NAME as the description. Is there a way the generated IFX components have some user defined PTC_COMMON_NAME? Alternatively, is there a way to edit my BoM table which reads asm.mbr.PTC_COMMON_NAME and displays in the description column, to show a custom parameter only for IFX items. Could some relation make this happen-display a custom parameter only for an IFX components and display the asm.mbr.PTC_COMMON_NAME value for any other parts in the same column for the assembly?

Hello, I recently opened Creo 7.0 and this orange marked report occured. It said, that I should send this black file to the technical Support, can you help?  -------------------------------------------------The trace creation timestamp is: Fr Nov 25 21:32:51 22The executable build timestamp is: Do Jan 28 16:21:00 21The datecode is: 2020454The pro machine type is: x86e_win64The process ID is: 6580The traceback type is : CRASHThe logger exit status is: 00003The Trail is: trail.txt.11The release is: 7.0The product version is: 7.0.3.0The product title is: Creo Parametric-------------------------------------------------Exception EXCEPTION_ACCESS_VIOLATION has occurred in the thread 14392. Main Thread 14392=====================0x00007FF978A1C170 NULL (NULL:0) (coretools_sh:0x00007FF978990000) ( 0xfe5aaa30, 0xfe5aab40, 0x4d, 0x3ae03188 )0x00007FF9175962A4 NULL (NULL:0) (uitools_sh:0x00007FF9171D0000) ( 0x3, 0xffffffff, 0x78e4d738, 0x0 )0x00007FF732E97DFE NULL (NULL:0) (xtop:0x00007FF72E

Hello,I had a problem on the server , I had to remove the FlexNet Admin License Server , even more so in C:\Program Files\PTC and in the services too , I need to install it again and I am not succeeding , would there be a way to remove it and install it again , or install over?

I have a weird issue with the AFX application. The 'Next' button in the 'New Profile' UI does not work for some profiles (Doesn't open the 'Position Profile' UI). Trail file shows: ProError: PRO_TK_GENERAL_ERROR (C:\Users\Samuel\source\repos\afx80\afx_commons\creo\mdl.cpp: 751)Does anyone know if this is a setting or regional settings issue or a problem with the app?

Hello,I have an error when I open some files on the network with a very long path in Schematic 8, the same error as follows print Schematic_2, in Schematic 4 the same file opens normally. Then when I open the file in Schematic 4 Schematic 8 stops working is there any solution for this?

How to create circles from centre co-ordinates data? Radius is same for all circles.Is there any way in which first we can define the coordinate axes then based on the centre co-ordinate and radius plot the circles. The boundary is a square, basically it is a microstructure consisting of circles inside a square. Data is in this form: Circle    x          y          r 1             2          2         1 2            10         5         1