Creo+ and Creo Parametric

I am getting this relation error on a few lines and i cant pinpoint whyleft and right sides are incompatible 

I am using Creo Parametric Release 8.0 and Datecode8.0.0.0I couldn't use the EZ tolerance analysis tool.Here are the errors that I facedYou have not checked out the license option. Please click "File->Options->Licensing" and choose required option from "Refresh license list".

Hi,I need to have two different Reps in the same sheet of a drawing.I start with the Master Rep and a certain scale of the drawing; when I change Rep and I choose other one the scale of the new one is different from the first Master Rep.I want the same scale. Is there an option or some other thing that can set the scale automatically?

Is it possible to use relations in a repeat relation to covert decimal #s to fractions? I was having issues with some ITOS formulas I found online but I developed some if statements that work well. (sample below) They work well at the part level but I am having issues adapting for the repeat region. WHOLE=FLOOR(ASM_MBR_FLAT_PATT_L)DECIMAL=ASM_MBR_FLAT_PATT_L-WHOLE IF (DECIMAL<.03125)FRACTION=""ELSEIF DEAD(DECIMAL,0.03125,0.09374)==0FRACTION="1/16"ELSEIF DEAD(DECIMAL,0.09375,0.15624)==0FRACTION="1/8"ELSEIF DEAD(DECIMAL,0.15625,0.21874)==0FRACTION="3/16"ELSEIF DEAD(DECIMAL,0.21875,0.28124)==0FRACTION="1/4"ELSE

Hi,I was wondering if the Creo parametric has a change of the phase in multiphase flow for evaporation and condensation? I see there is evaporation and condensation only in the cavitation model. For example, in the inlet boundary condition there are 3 phases water_vapor(v1)=0.4, N2(v2)=0.35 oxygen(v3)=0.25. After passing from heat exchange with heat source 200 W, what is the volume fraction of water_vapor and water_liquid?I can't see any option for change of the phase and phase interaction because of evaporation and condensation of liquid or gas.Thanks

Is there anyway I can modify the spline created during section view? (Image attached for reference)

Check out this video on Creo Parametric 8 & 9 Update from PTC Application Engineers Presenters: Lee Goodwin (Solution Consulting, Principle) and Ryan Butcher (Solution Consulting, Fellow). Creo ECAD MCAD Collaboration Learning  

Hello, In a repeat region I put the relation ITEM=500+rpt_index to start from 501. --> okThen to reorder some components I "Fix index" i.e.: 503 fixed to 2 become 502.It works perfectly for some assemblies and not for others.When it doesn't work,- 503 fixed to 2 move to the 2nd row instead of 3 -->ok- 503 is still displayed instead of being changed to 502. rpt_index is well 2 for it. It seems like the formula ITEM=500+rpt_index is not calculated anymore. Again, on some drawings it works fine. Assemblies are build with a similar method.I suppose it can come from an option in the drawing template but I don't find what is different.Does anyone have an idea ? 

I am using Creo Parametric Release 4.0 and DatecodeM150Sections have never worked at places where they would cut a spring which is part of an assembly. The section looks fine in 3d, but fails on the drawing. Currently the spring has to be excluded from the section for it to work. Is this a known bug? Will this bug be fixed in Creo 8?

I am using Creo Parametric - Release 6.0 (connected) Release 6.0 and Datecode6.0.6.0The dimension display is set to retain 1 decimal place, but the actual dimension is still an integer     Translated with Google translate by Iuliana Nuta, 11 june 2022

I am using Creo Parametric Release 5.0 and Datecode5.0.4.0 The PROE image file is imported into CREO, and there are missing parts Here are the errors that I facedThe PROE image file is imported into CREO, and there are missing parts     Translated with Google translate by Iuliana Nuta on 22 july 2022

I have two question on the notes in creo 4.1. can i change the default note name for ex Note_01 to Gen_note0012. is there a way to create a parameter note without opening the parameter box itself like can i add a relation that would equate Note_001 to a parameter? (not &parameter name) ex. note_001= Note Parameter named noteA_001 

HelloI try to analysis universal joint (Cardan's joint) in MDOthe mechanism is composed with 2 universal joint, i have a slide between U joint.on enter shaft, i use a speed servomotoron exit shat, i use a torque servomoteurIt'OK,  a speed and torque values are consistent But, for design the bearing betwenn cross and fork, i need to calculate the forces on crossof course, this force is torque/ fork radius (tangential force)I would like to find this result with the Creo's measures, but i can't do it!    

Folks i am trying to move a knob using the slot connection but i get these errors: 1. Servo motor on slot in the assembly model cant be satisfied2. The rigid body 1 connected by Connection_7 in the assembly cant be properly oriented3. The following kinematic loop cant be closed: Ground-body1-Ground I dont understand the last error as it shouldnt apply to my problem thanks     

I'm drilling a plate with counter bored holes. Generate a .nc file and when I go to post it I get this "Error type 3 detected". The error comes up right after I select a post. The post works on several other files so I don't think that is it. Any thoughts?Josh

We have a user that just insists on using non-standard arrowheads, and all threats have failed to stop it.  🙂Is there a way to hide the arrowhead type context menu, or a config or DTL file option to lock the arrowhead style?

Check out this video on Creo ECAD MCAD Collaboration from PTC Application Engineers Presenters: Jason Petersen (Solution Consulting, Principle) and Ryan Butcher (Solution Consulting, Fellow). Creo ECAD MCAD Collaboration Learning  

Hi everyone,It must be an answer for this one, but can't find it... Upon finishing a feature modification in a pattern, I was to modify other features before clicking regenerate, however, CREO started to regenerate everything immediately, except for the features that have been set as read-only ahead of the pattern. There are 12 patterns in the model tree, I need make simple modification (i.e., change the number of member) to all of them. After each change of the number of member in a pattern, CREO takes two minute+ to regenerate. 12 patterns means half a hour for regeneration! It must be an option to set to avoid the automatic regeneration. I am using CREO 6 in offline mode. Thx,JSBTW, to generate a 48 x 116 pattern of simple cutouts in a flat plate, CREO spent at least 8 hours (from Friday morning to next Monday morning) to finish it on my computer with 128GB installed RAM.

Would have as a local exchange where to save the information schematics (cahe) , today is in this location C:UsersAdministratorAppDataRoamingPTCCreoSchematics wanted to put to save in another Drive ?

Hi,I want ro read onto step file the annotation make in a part as dimension, tollerance and note.How to export, in a step file, annotate as note?

why point defined on hole axis can not be chosen for spot welding?

I am using Creo Parametric Release 7.0 and Datecode7.0.3.0Hi,I would like to know the option to kill Creo in background completely.

I am using Creo Parametric - Release 4.0 (connected) Release 4.0 and DatecodeM010   In the drawing, after segmenting the table in the repeated area, you can manually select a separate table  and you can get the selected table through ProSelbufferSelectionsGet. How can I get each segment of the table after iterating through the table with code. Translated by Corina Ionescu Translated with Google Translate, on July 20th 2022工程图中，对于重复区域的表格进行分段以后，手动可以选择单独的表格，并能通过ProSelbufferSelectionsGet获取到选中的表格。用代码遍历表格后，如何获得每一段表格。

I am using Creo Parametric Release 5.0 and Datecode5.0.3.0Assembly is not getting deleted and assembly is getting displaced from the given constraints even though we have assigned the constraint. Kindly look into this ASAP